Question about Cars & Trucks

Open Question

Rear wing goes up when car started now it has stuck in up position and lights on switch are flashing help thank u

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: The two rear

Try replacing the switch in the door. They tend to fail after a while.

Posted on Aug 25, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 Chevy Silvarado 1500 LS turn signal lights on the front passenger side don't work and rear goes fast...


Circuit/System Description
Ground is applied at all times at G201 to the turn signal/multifunction switch. The turn signal lamps may only be activated with the ignition switch in the ON or START position. When the turn signal/multifunction switch is placed in either the TURN RIGHT or TURN LEFT position, ground is applied to the body control module (BCM) through either the right turn or left turn signal switch signal circuit. The BCM then applies a pulsating voltage to the front and rear turn signal lamps through their respective control circuits.
.
Did you check the RT STOP TRN fuse 15amp insturment panel fuse box.
Fuse Block - I/P
Left of the I/P behind the side trim panel
If the fuse is good , you could have a wiring problem or the BCM is bad .

Sep 08, 2017 | Cars & Trucks

3 Answers

Car won't start! Goes crazy when I turn key with lights flashing...


I would start by making sure all of your connections at the battery are clean and tight. A loose or corroded connection can wreak havoc with your starting system. After you have verified that all connections are good, make sure your battery is in good condition. If everything else checks out good you might be looking at having your ignition switch changed.

Apr 24, 2013 | Buick Rendezvous Cars & Trucks

2 Answers

03 grand am 3.4l no crank at all. All the light on dash work good fuel pressure starter spins and engine starts and then stalls when jumping the starter directly installed new pass lock switch and...


If the Passlock switch has been replaced, the computer has to "learn" the new Passlock code. You will need to hook up a battery charger to perform the learning process. (It takes about 30 minutes with the key in the "ON" position and it will run the battery down.)

Step 1:

Turn the key to the "START" position and release to the "RUN" position. The "SECURITY" light will be flashing. After about 10 minutes, the light will stop flashing.
.
Step 2:

Turn the key "OFF" then back to the "RUN" position. (Do NOT try to crank it yet) The light will start flashing again. Wait about 10 minutes for it to stop flashing.
.
Step 3:
.
Turn the key "OFF" and back to "RUN" one last time. The light will be flashing again. This time, when it stops flashing, do not turn the ignition off. Instead, turn the key from the "RUN" position to "START". The engine should start and run. The computer has now learned the new Passlock code.

Please help myself and others by taking the time to rate my answer. Thank yoou for using fixya!

Feb 08, 2011 | 2003 Pontiac Grand Am

1 Answer

95 911 wing is stuck in the up position


Hello there
Your problem could be the rear gear is broken.It is located on the left inside your tail under the plastic cover.To remove use phillips screwdriver and try to diconect the gear cable.If the wing goes down it is the gear.If not the gear try to lok for an relay which is on pass.side under the dash-behing knee pad.This relay controls the manual and an electric operation.
Part number 964 618 212 00


ivan
proporsche@yahoo.com

Oct 10, 2010 | 1995 Porsche 911

2 Answers

Blinking airconditioning lights


Hi there,

TO INITIATE TESTS:
1. Set blower to HIGH
2. Set mode position to PANEL (AC vent air)
3. Open all AC outlets
4. Temp. on full cold
5. Start engine
6. Push WASH and REAR WIPER switches for 5 seconds until all panel lights are on solid
System will then go through it's paces as it calibrates the climate controls
7. When calibration is complete only the REAR WIPER switch/light should be flashing. Press this switch to extinguish the light
This will stops blinking lights.....

Good Luck!!

Thanks

Aug 08, 2009 | Plymouth Voyager Cars & Trucks

1 Answer

I have been told to fix my microchips of my spolier therefore i have done this and it still does not work what elce could it be? I have also been told that it might not work because the front spolier does...


the active aero system works the front and the rear at the same time,it goes thru the switch at the center console-if the front does not work,the rear will not work also even if you replace the limiter switches on the rear wing,the rear wing has to be timed to the wing motor to work also-it is pretty hard if you dont know how to do it-good luck

Jun 20, 2009 | 1994 Mitsubishi 3000GT

1 Answer

Need to reset flashing instrument lights


Here's what i found is supposed to work.

1. Set blower to HIGH
2. Set mode position to PANEL (AC vent air)
3. Open all AC outlets
4. Temp. on full cold
5. Start engine
6. Push WASH and REAR WIPER switches for 5 seconds until all panel lights are on solid
System will then go through it's paces as it calibrates the climate controls
7. When calibration is complete only the REAR WIPER switch/light should be flashing. Press this switch to extinguish the light
and all should work normally.

Mar 26, 2009 | 1998 Plymouth Voyager

1 Answer

"Cruise Not Available" & "Check Rear Lights" flash from message c


Hi Don

I recomend you try this first of all.

Try disconnecting the positive battery + & negative - terminals.

Turn the ignition key several times to erase the computers memory.

Reconect the battery + terminal and then - and start the car.

Your fault code, will hopefully not return.

Good Luck !


John.

Jan 19, 2009 | 2005 Jaguar XKR

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...