Question about Cars & Trucks

1 Answer

How to torgue 3.5cylinder heads - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,248 Answers

I looked at an Altima 3.5L
I don't know if your going to use nm or ft lbs? no need for both. I did post torque specs.

how to torgue 3.5cylinder heads - torgue-3-5cylinder-heads-qkl5oeqlgz4o2bkd2pxxfrwt-5-0.jpg

Posted on Dec 02, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need torgue specs for bolts on head of my 2000 vauxhall tigra 1.4


Cylinder head bolts (You must use new bolts)
stage 1 ... 25 Nm (18 lb ft)
stage 2 ... angle tighten + 90 degrees
stage 3 ... angle tighten + 90 degrees
stage 4 ... angle tighten + 90 degrees
stage 5 ... angle tighten + 45 degrees

Remember use NEW bolts, these are called torque to yield bolts, they stretch like a linear spring and they only last one use.

Jun 25, 2016 | Vauxhall Cars & Trucks

1 Answer

Need to get torgue specs for cylinder head


My best suggestion is to order the service manual for the vehicle. They range in cost but you can get them for around $30.

Sep 08, 2014 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

Torque specs for 3.9l engine cylinder head and crankshaft bolts.


Page 3-26 of Chilton's reads:
14. Using no sealer whatsoever, install the new head gasket(s) to the block. Clean, dry and lightly oil all head bolts threads. Install the heads and install the head bolts.

Tighten head bolts in sequence to 50 ft. lbs. (68Nm). Repeat the sequence retightening the bolts to a final torque of 105 ft. lbs. (143 Nm) and repeat the second step to ensure that all bolts are accurately torqued.

torgue chart from chilton (page 3-11) for your engine and year show:
main bearing bolts 85 ft lbs
rod bearing bolts 45 ft lbs
crankshaft damper bolts 135 ft lbs
flywheel bolts 55 lbs

Mar 27, 2011 | 1992 Dodge Dakota

1 Answer

Water leaking from engine head bolt, what would cause that to happen?


Some engines had head bolts that went thru water jackets, remove and put sealer on it then torgue back down. Does it overheat? If that doesn't fix needs head gasket.

Dec 15, 2010 | 1997 Pontiac Sunfire

1 Answer

I would like to know the location of the Idle Control Valve for the 1996 Saturn SL1


there are to eletrical components next to one another. The throttle position sensor and the idle control vavle. They are right where the air supply housing goes into the metal part of the air intake system. Right at the firewall the air intake line, a big rubber hose, attaches to the metal trhottle body. The bottom of the two is the idle control valve. It has an oblong electrical connection and uses a small "torgues" type male wrench to get the two screws out. Torgues is the star shaped screw, rather than a hex head of phillips head type screw.

Jul 27, 2010 | 2001 Saturn S-Series

1 Answer

Torgue specs for head bolts


I would call autozone, in there computer when you ask to purchase a head gasket, they can tell you the order and torque for the head bolts. That is the quickest method to advise. I hope this helps

Aug 08, 2009 | 1999 Volvo S80

1 Answer

Head bolts


I'm assuming you meant a 1.8L 4V, if so the torgue settings for the head bolts are
stage 1: 30 ft-lbs
stage 2: 44 ft-lbs
stage 3: Angle-tighten a further 90-degrees
stage 4: Angle-tighten a further 90-degrees

Also I recommend you buy new cylinder head bolts from the vdub dealer, they say you don't have to with a gas engine but only with diesel engines you should, from my past experience it felt like the old bolts were going to snap off to be safe buy new ones. If you have never done this before "stage1" this means each bolt gets this one time, then after you have done each bolt at this torgue then you do the bolts again (stage 2) with this torgue ect. Remmeber to always cris cross your bolting and work from one side to the other the same time for each stage. Vdubs 4-ever !

Mar 23, 2009 | 1997 Volkswagen Golf

2 Answers

Cylinder head torque settings 1990 2.6L isuzu motor


From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Mar 21, 2009 | 1990 Isuzu Spacecab

1 Answer

Cars-


please specify what torque you need. The head bolt torgue? The lugnut torque? The motor mount torque. Every bolt has a required torque. Mr. Rodney Long

Jul 02, 2008 | 1995 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...