Question about Cars & Trucks

Open Question

Grohtherm1000 mixer bar. Reinstalling an older version. Looking at it with the stat on the right and the outlet looking down, is the cold inlet at the rear on the left or right? Thanks, David

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 231 Answers

SOURCE: left rear wheel is inset but the right rear wheel sticks out the side

have your U-bolts that hold the rear axle checked to see if they have worked themselves loose or stretched.

Posted on Oct 07, 2008

Ad
ourhowse
  • 2007 Answers

SOURCE: 1997 Toyota Camry V6 3.0L.....How to Connect (Route) Plug Wires

Go to this link. It should help. http://autorepair.about.com/library/firing_orders/bl-fo-4998.htm

Posted on Jun 15, 2009

alicantecoli
  • 22156 Answers

SOURCE: hit in rear right tire and tire is bent in at the

think this vehicle is a write off ,the cost of repair will be more than its worth

Posted on Jul 15, 2010

  • 610 Answers

SOURCE: looking for cylinder order, is #'s 1,2,3,4 on the

1234 down the right side 5678 down the left. this is veiwed from the rear of the engine as if you were sitting on the transmission.

Posted on Dec 21, 2010

AskJack
  • 117 Answers

SOURCE: hi, my name is David. I have a 03 GMC Yukon XL.

Well, you should first check ALL, your vehicles fuse boxes and make sure they're in working order.

Assuming that your air conditioning compressor clutch is engaging and in working order.
and the the fuses are good. Then most likely, it is as simple as needing to fill it up with refrigerant...

If you dont have an autoparts store nearby, well even if you do. The R134a is cheaper at most stores such as Walmart, K-Mart, etc, etc...

As for cost, an 18oz cannister with a filling tube and gauge runs around 18.00 at most auto parts store... Instructions are on the can. including what the typical PSI level should read from a system in working order.

Good Luck and Happy Motoring

Respectfully

Posted on Jun 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for location on engine side of heater core hoses. I can see the outlet hose but am unable to locate the inlet hose to the engine.


Sounds like an air pocket. Follow the bleed procedure for you vehicle. Many vehicles have a bleed valve for this issue..not familiar with yours but a Google search should answer that question.

Oct 28, 2016 | 2005 Hyundai Santa Fe

2 Answers

What causes heater to only blow cold air?


there is a thermactor valve that shuts off flow to heater core in summer months , also there is a damper door activator that can "stick" to the cold side , these two items are next to check

Jan 30, 2016 | Cars & Trucks

1 Answer

In an inline 4 cylinder 8 valve scorpio 2006 crde engine having 1-3-4-2 firing order which valve is first - the outlet or the inlet


from the belt side first valve is inlet second valve is exhaust..bigger valve is inlet small valve is exhaust also you will have a black colour in exhaust valve stems...

Feb 28, 2013 | 2011 Mahindra Scorpio

1 Answer

How to solve this no heat problem?


Blend doors are not working.

May 17, 2017 | 1996 Dodge Caravan

1 Answer

I have a 1986 Scirocco 16V race car. the engine is basically stock. I have rebuilt the entire engine, cleaned out passages, etc. It runs fine but overheats every time. I replaced the water pump,...


the water flow through the heater system is part of the flow on these vehicles ,so reconnect them then check the thermostat is the right one as one version has a two part thermostat ,it has two water closing parts and the other type has one like conventional stat and if you fit this one in the other engine then it will overheat .start engine and see if any bubbles come up in the bottle when it runs ,i susp?ct the head is distorted or the water ports are corroded allowing pressure into the cooling system

Aug 01, 2011 | 1987 Volkswagen Scirocco

1 Answer

Truck is running hot. Relaced thermasta and still runs the same. Noticed the top hose gets real hot while the bottom one doesnt. Dont get it.


The cooling water doesn't seem to making it through the radiator. Look for plugged radiator, blocked upper or lower hose, or ineffective water pump. Remove the inlet and outlet hose after draining coolant from the radiator. Hold your hand over the lower hose outlet while someone fills the radiator with cold water. When full, leave the cap off, then remove your hand from the outlet. If the core is unobstructed, the water will rush through it in a few seconds. Check the upper hose inlet--there should be no obstruction. Inspect the interior of each hose looking for collapse or other blockage. If ok, that leaves the water pump--remove it from the engine and check that the impeller turns solidly with the driving pulley. Any looseness there is grounds for replacement. Hope some of this helps!

Jun 29, 2010 | 2004 Dodge Ram 1500

2 Answers

Looking for thermostat locatiion on 3400 motor


remove air cleaner intake duct, partially drain cooling system, remove radiator inlet hose from water outlet hosuing which is down on side of engine in between cylinder heads and above trans, remove exhaust crossover pipe,remove water outlet housing bolts, remove water outlet housing and gasket, remove thermostat clkeaning mating surfaces and reverse install procedure.

Jun 17, 2010 | 2003 Chevrolet Impala

1 Answer

Cooling fan won't turn off after car has been shut off for more than an hour.


Over run on radiator fans is normally caused by a stuck relay, but if the fan eventually goes off, then the relay is working, otherwise it would keep running until the battery dies. there may be a timer in the relay to allow the fan to "run on", so as to not only cool the rad, but also to cool the engine bay, where the heat will well up. If a new stat was put in, it could be that the stat is stuck, and one side of the system is cold the other hot. check the inlet and outlet hoses on the rad, if the temprature diffference is extreme, then the sat may be stuck closed, or install backwards. Air is a poor onductor of heat compared to water, so unless there is an airlock in the system which will be evident from the differing heat areas of inlet outlet, the only other suggestion is to check that the water pump is working. it may have failed, or be clogged.

Hope thtas help.

May 05, 2010 | 2003 Jeep Grand Cherokee

1 Answer

Poor heat output motor runs cold


Check the hoses going to inlet and outlet to heater core. You may have accidentaly hooked them up backwards since you said you flushed the heater core out. Also did the barsleak have the aluminum filings in it?

Jan 04, 2009 | 1994 Chevrolet Astro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...