Ford fiesta 1.6 petrol engine cylinder head torque settings and main and big ends torque settings

2012 ford fiesta cylinder head torque?

Fiesta Faction https://www.fiestafaction.com > threads > 2012-ford-fi...
May 18, 2018 - Tighten to 15 Nm (133 lb-in.) Tighten to 35 Nm (26 lb-ft.) Tighten an additional 75 degrees. There's a tightening order, but the manual doesn't ...

Need cylinder head torque specs for 2013 ford fiesta 1.6 L.

JustAnswer https://www.justanswer.com > Car Questions
May 29, 2018 - - Stage 1: Tighten to 5 Nm (44 lb-in). - Stage 2: Tighten to 15 Nm (133 lb-in). - Stage 3: Tighten to 35 Nm (26 lb-ft). - Stage 4: Tighten an ...

1 answer · Top answer: yes it is you can always get me back through here even after you rate me.

Pictures of tightening sequence

https://www.google.com/search?q=Ford+Fiesta+2011+torque+settings+cylinder+head

..

https://www.google.com/search?q=2012+chevrolet+captiva+2.2+VCDi+diesel+cylinder+head+torque+specs

https://www.google.com/search?q=2012+chevrolet+captiva+2.2+VCDi+diesel+big+end+torque+specs

Not too much information on the 2.2 diesel. A service manual is the best idea.

..

Ford Fiesta Fiesta 1.6 16V Duratec (1595ccm) 2002-2008

https://www.carrepairdata.com > eng > fiesta > fyja__fyjb
Ford Fiesta Fiesta 1.6 16V Duratec (1595ccm) 2002-2008 ; Cylinder head tightening torque 1, 15Nm ; Cylinder head tightening torque 2, 30Nm.

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3
PDF
Rod Torque. Main Torque. Cylinder Head Bolt Torque. ACURA. 1.6 ... 55-60 FT/LBS. FORD. 2.5. 155. DURATEC. 95-02. 26-33 FT/LBS, + 90-120^ USE. NEW BOLTS.

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

2ltr petrol engine, mains stage1 44 to 51 nm stage 2 85 to102 nm
big ends stage 1 20 to 23 nm stage 2 40 to 47 nm

Don't worry I'm sure you will get the solution of your problem, just check the link I attached
FORD FIESTA BODY REPAIR MANUAL 2008 2010 DOWNLOAD

A cheap shop manual will have this and much more. If you are in this deep you probably need one.

Please follow the link for all the engine settings, every nut and bolt. http://www.formulafordzetec.co.uk/linked/engine%20torque%20wrench%20settings.pdf

1997 Toyota Prado 5VZ-FE
Cylinder head bolts:
Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Specifically which torque settings are you referring to. There are thousands to choose from. Please give an example such as "differential carrier", "cylinder head", "exhaust manifold to engine block" etc.