Question about Cars & Trucks

Open Question

Instlation of a rear view camera for a 1986 countash

How do i get the front part of the head liner and piller off

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Static van ceiling has bowed but not wet


remove all plastic trim from around windows and all piller trim head liner should come down

Feb 23, 2014 | 1993 Dodge Caravan

1 Answer

Fuel filter location


if its a petrol it is at the rear of the left hand front wheel arch liner, remove wheel, displace rear of liner, it has quick release pipe connectors and is held by a 8mm head bolt.

Jan 27, 2014 | 2000 Jaguar S-Type

1 Answer

How do you replace stop lamp inside car on rear window


Manual says to remove rear seat bolsters

I guess that is the rear window trim

I have removed the front ones on my LS but never
the rear ones

I guess they just pull away & are spring loaded or attached

Then pull down the head liner & remove two bolts &
unplug the rear high stop lamp assy

Jan 28, 2013 | 2002 Lincoln LS

1 Answer

How to replace right side low beam head light bulb?


{: ) REMOVE THE RIGHT FRONT WHEELHOUSE LINER
The wheelhouse liner is sometimes called the mud guard or the splash shield, whatever.
You may remove the right front tire.
-Start removing all those push pins and #7mm screws. No need to remove the entire liner. You may loosen only the half portion, just enough clearance for your arms to reach inside and aim for the rear of the headlamp.
-Reach for the Headlamp Bulb Accessory Cover. Rotate the cover counterclockwise and remove.
-Release the bulb from the headlamp assembly (turn counterclockwise) Disconnect the electrical connector. Just remember the positioning of the bulb so you can swiftly reinstall a new bulb.

Feb 24, 2011 | 2008 GMC Acadia

1 Answer

Trying to remove the battery from my 2007 soltice


Hello robert.... Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .


Joe
Thanks for choosing Fixya!

Jan 30, 2011 | 2007 Pontiac Solstice Convertible

1 Answer

Where is the battery located?


Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure . 1737d1122299169-solstice-service-battery-replacement-procedures-158wilmingtoncarshow36.jpg
hope this helps . please rate my response.

Nov 28, 2010 | 2007 Pontiac Solstice Convertible

1 Answer

Sunroof problem Merc 190e 1986 Model


I would assume it is the same as my 1983 sun roof. I hade to remove the head liner and it unblots from the uner side. tilt it to the side and remove through the rear door. I hope this helps.

Jun 29, 2009 | 1986 Mercedes-Benz 190

1 Answer

Loose liner/sleeve in a 2.2 diesel isuzu


when the head is put on it holds it down,check protusion height with a straight edge .Providing they are all the same height you dont have a problem

Feb 16, 2009 | 1986 Isuzu Trooper

1 Answer

Crank sensor


CRANKSHAFT POSITION SENSOR - 3.9 - 5.2 - 5.9L ENGINES
REMOVAL

The sensor is bolted to the top of the cylinder block near the rear of right cylinder head

Note: The sensor is accessed by removing the right front fender liner

Remove right front tire and right front wheelhouse liner.
Disconnect crankshaft position sensor pigtail harness from main wiring harness.
Remove two sensor (recessed hex head) mounting bolts on the Crankshaft Position Sensor
Remove sensor from engine.

INSTALLATION
Position crankshaft position sensor to engine.
Install mounting bolts and tighten to 8 N·m (70 in. lbs.) torque.
Connect main harness electrical connector to sensor.
Install right front tire and right front wheelhouse liner.

Feb 07, 2009 | 1999 Dodge Durango

1 Answer

Where is the crank sensor located?


The sensor is bolted to the top of the cylinder block near the rear of right cylinder head
The sensor is accessed by removing the right front fender liner
  1. Remove right front tire and right front wheelhouse liner.
  2. Disconnect crankshaft position sensor pigtail harness from main wiring harness.
  3. Remove two sensor (recessed hex head) mounting bolts
  4. Remove sensor from engine.

Jan 08, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...