Question about 1996 Chevrolet Blazer

1 Answer

Where is the oil pressure cut off switch on a 96 blazer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 832 Answers

On engine block

Posted on Dec 02, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 94' Chevy blazer 4x4, 4.3 L Vortec. It started knocking out of the blue.


No this is a bullet proof engine, but things like this do happen from time to time.

Apr 08, 2017 | Cars & Trucks

1 Answer

96 Chevy blazer how do I get out of safe mode ran low on oil now runs an drives but won't let car go fast past 2000rpms


The computing system on your vehicle has no safe mode for running low on oil . The only thing that will happen is the check gauges light will come on.
The oil pressure gauge is an analog device that is located in the IPC. The oil pressure gauge is operated directly by the oil pressure sensor circuit. As the engine oil pressure changes, the resistance of the sensor and the current flow in the oil pressure gauge changes. The current flow in the oil pressure gauge causes the needle to move in order to appropriately display the engine oil pressure. A sensor resistance of 1ohms will display as 0 kPa (0 PSI) and a resistance of 88 ohms will display as 80 kPa (80 PSI ). The IPC also monitors the oil pressure sensor circuit and interprets the current flow in this circuit in order to determine when the engine oil pressure is too low. If the oil pressure is too low, the check gauges tell tale will turn on. The oil pressure sender is located on the left side of the 2.2L. The 4.3L engine, oil pressure sender is located at the top left side, near the distributor/high voltage switch.
Try disconnecting the battery cables an hold them together for ten minutes , reset ECM !

Nov 08, 2015 | Cars & Trucks

1 Answer

Lost all oil pressure and the blazer shut off. its a 1985 2.8 v6. is there a automatic cut off in the car? And how hard is it to change the oil sending unit?


The fuel pump gets power from the oil pressure switch once the engine is started. So if oil pressure drops below 5 psi the engine should stop.
Other than a special socket to fit the oil pressure switch, its not too difficult to change.

Jan 23, 2014 | 1985 Chevrolet S-10 Blazer

1 Answer

How do your remove oil spout on 96 blazer


just turn it out of the valve cover some dont have threads then you just pull it out

Feb 26, 2013 | Chevrolet Blazer Cars & Trucks

1 Answer

My 98 blazer sounds great until it gets warm


I switched to Lucas oil with adding Lucas oil stabilizer and it increased my low oil pressure problem

Mar 13, 2012 | 1998 Chevrolet Blazer

2 Answers

Is there a reset button on this fuel pump


CHEVY DOESN'T USE A FUEL PUMP RESET/CUTOFF SWITCH, FORDS USE THIS FEATURE, ON A CHEVY IT IS DONE WITH THE OIL PRESSURE CUTOFF SWITCH, SO IF U LOOSE OIL PRESSURE THE FUEL PUMP CUTS OFF, THIS OIL PRESSURE FUEL PUMP CUTOFF SWITCH AND IT'S WIRING ARE NEAR THE OIL FUILTER UNDER THE TRUCK.

Apr 21, 2010 | 2000 Chevrolet Blazer

1 Answer

My 1990 S 10 blazer is having problems with the oil pressure. it will not keep the pressure up on it I have change the sensor and it still goes down causing the motor to shut off


First check the oil pressure with a gauge screwed directly into the hole where the sensor is screwed in. If it is good than change the fuel pump cut off switch, this is the one that turns the fuel pump off in the event of an accident. If the oil pressure is indeed low you need to look at the mileage and service record of the car, maybe an oil pump replacement would help, but if engine wear is the culprit an overhaul will be the only cure.

Mar 11, 2010 | 1989 Chevrolet S-10 Blazer

2 Answers

No power at fuel pump


Your fuel pump relay is triggered by your oil pressure switch,try jumping across to bypass your fuel pump relay if truck runs then figure out why relay is not being triggered.

Aug 24, 2009 | 1997 Chevrolet Blazer

1 Answer

Fuel pump isn't working


the fuel pump is very comman for the blazers but another thing you need to do is to make sure there is not too much oil in ur motor there is a sensor that cuts off the fuel pump if there is too much oil

Apr 02, 2009 | 1999 Chevrolet Blazer

3 Answers

My 99 chevy blazer is getting intermittent fuel


the catalytic converter could be clogged

Oct 30, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...