Question about Cars & Trucks

Open Question

How to remove starter housing on bc 1800 super blower vac

No spark need to check coll

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a talon 32cc blower vac which will not start. Have replaced spark plug. Could the problem be the ign coil?


probably not
check for spark at the plug
check the stop switch and wiring for the coil
next check the primer bulb and replace it if it is cracked

Jul 22, 2016 | Cars & Trucks

1 Answer

How to install blower motor in 2000 saturn ls2


You go in from the engine side . Disconnect the negative battery cable.Remove the super blade assembly, both. Pull up the cover that houses the interior filter and remove. Remove the wiper motor assembly.The blower is directly under it. Remove the four screws holding the blower cover on and remove.There is only a flat black plate that holds the blower in place .Disconnect the power line running to it, and pull up.

Aug 14, 2014 | Saturn L-Series Cars & Trucks

1 Answer

Oil in spark plugs


Any time you see oil getting inside of the spark plug and wires means that the spark plug tube seals are bad and are letting oil from the heads cover into the spark plugs solution will be remove the head cover anf replace the spark plug tube seal

Sep 30, 2012 | 2005 Chevrolet Aveo

1 Answer

Blower motor repair


Section 12-02A: Heating and Defrosting, Ranger, Explorer 1995 Aerostar/Ranger/Explorer Workshop Manual REMOVAL AND INSTALLATION Blower Motor and Blower Motor Wheel Assembly Removal and Installation
  1. Remove the windshield washer bottle.
  1. Position the speed control servo out of the way (if so equipped), refer to Section 10-03A.
  1. Disconnect the wire harness connector from blower motor by pushing down on the connector tabs and pulling the connector off the blower motor .

    m5095a.gif


    Item Part Number Description 1 18527 Blower Motor 2 19A786 Blower Motor Housing Tube 3 - Heater Case Insulator
    (Part of 19850) 4 19930 Blower Housing 5 - Electrical Connector
    (Part of 19805)
  1. Disconnect the blower motor housing tube (19A786) at the blower motor .
  1. Remove three screws attaching the blower motor to the A/C blower housing (19930) .
  1. Holding blower motor housing tube aside, pull the blower motor from the heater plenum chamber case (18A484) and remove it from the vehicle.
  1. Remove the blower wheel hub pushnut and, if applicable, the clamp from the shaft. Then, pull the blower motor wheel (18504) from the shaft. For installation, follow removal steps in reverse order. Check system for proper operation. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.

Nov 16, 2010 | 1995 Ford Explorer

1 Answer

I need to know how to get to the blower fan as it is not kicking on/blowing any heat/ air and my manual does not say where it is located and how to get to it.


I will paste instruction from autozone.com below. Also, check my solution at http://www.fixya.com/cars/t6104871-heater_fan_just_quit_working_find_fuse.

  1. Disconnect the negative battery cable.
  2. Remove the glove box assembly, lower right side instrument panel trim cover and right cowl trim panel, as required. Disconnect the blower lead wire connector.
  3. If the vehicle is equipped with air conditioning, disconnect the 2 vacuum lines from the recirculating door actuator and position the actuator aside.




0900c152802686b4.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Blower motor housing cover



0900c152802686b5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Blower motor and wheel assembly



0900c152802686b6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Remove the spring-type retaining clip to separate the wheel from the blower motor

  1. Remove the 2 screws at the top of the blower housing that secure it to the unit cover.
  2. Remove the 5 screws from around the blower housing and separate the blower housing from the unit.
  3. Remove the 3 screws that secure the blower assembly to the heater or air conditioning housing and remove the assembly from the unit. Remove the fan from the blower motor by removing the spring-type retaining ring from the center of the blower wheel. Note the location of the fan-to-blower motor assembly for correct installation.




0900c152802686b7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: To gain access to the blower motor, unplug the electrical connectors from the glove box lamp, ...



0900c152802686b8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: ... then remove the glove box assembly from the dash panel

Sep 21, 2010 | 1989 Chrysler New Yorker

1 Answer

Where is the blower motor... i know that is the problem, but where and how do I change it. i already have the part


Blower Motor Removal & Installation Front To Remove:
NOTE: The blower motor is positioned on the passenger side of the vehicle beneath the instrument panel, and can be removed from the vehicle without removing the HVAC housing.
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Passenger side cowl trim panel
    • Carpet to access the front upper screw that secures the air inlet housing
    • Recirculation door actuator
    • Recirculation door actuator wire lead from the routing clip located on the lower air inlet housing and position the wire lead aside
    • Blower motor wire lead connector from the blower motor resistor or power module, depending on application. Lower Air Inlet Housing chr_pacific_lwr_inlt_hsng.gif

    • One screw (from the top) that secures the lower air inlet housing to the upper air inlet housing
    • Four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and remove the lower HVAC housing Blower Motor Wire Lead Grommet chr_pacific_blwr_wrg_grmmt.gif

  3. Feed the rubber blower motor wire lead grommet through the opening in the lower air inlet housing.
  4. Push the blower motor wire lead through the opening in the lower air inlet housing and remove the lower air inlet housing from the vehicle.
  5. Place the recirculation-air door as needed to access and remove the three screws that secure the blower motor to the lower half of the HVAC housing.
  6. Lightly bend the recirculation air door far enough down to remove the blower motor and wheel from the HVAC housing. Blower Motor Mounting Tabs blwr_mnting_tabs.gif

  7. Remove the blower motor and wheel from the HVAC housing. Make a note of the location of the blower motor mounting tabs.
To Install:
  1. Install or connect the following:
    • Blower motor and wheel to the lower half of the HVAC housing and line up the blower motor mounting tabs to the correct location on the HVAC housing
    • Blower motor and wheel into the HVAC housing by lightly bending the recirculation-air door far enough down
    • Three screws that secure the blower motor to the HVAC housing by positioning the recirculation-air door as needed
      1. Torque to: 17 inch lbs. (2 Nm)
    • Blower motor wire lead through the opening in the lower air inlet housing and seat the rubber grommet into the lower air inlet housing
    • Recirculation-air door pivot into the lower air inlet housing
    • Four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and the lower HVAC housing
      1. Torque to: 17 inch lbs. (2 Nm)
    • One screw (from the top) that secures the lower air inlet housing to the upper air inlet housing
      1. Torque to: 17 inch lbs. (2 Nm)
    • Blower motor wire lead connector to the blower motor resistor or power module, depending on application
    • Recirculation door actuator wire lead into the routing clip located on the lower air inlet housing
    • Recirculation door actuator
    • Carpet
    • Passenger side cowl trim panel
    • Negative battery cable
  2. Perform the heater-A/C control calibration procedure.
Rear To Remove:
NOTE: The rear blower motor and blower wheels are repaired only as a balanced unit. The entire blower motor and wheel assembly must be replaced if either component is fault or damaged.
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Front center floor console cover
    • Negative battery cable Rear Blower Motor Housing chr_pacific_rear_blwr_hsng.gif

    • Body wire harness connectors from the rear blower motor power module and the rear mode door actuator
    • Body wire harness bracket from the console support bracket
    • Eight screws and the two console support brackets from the floor console base and duct assembly
    • Four screws that secure the rear blower motor housing to the floor console base and duct assembly
    • Rear blower motor housing and place it on a bench
    • Rear blower motor wire harness connector from the power module
    • Eleven retaining clips and three screws that secure the housing together
    • Two halves of the housing
    • Blower motor wire harness and grommet from the housing and remove the blower motor
To Install:
  1. Install or connect the following:
    • Rear blower motor into the housing and install the blower motor wire harness and grommet
    • Two halves of the rear blower motor housing and install the eleven retaining clips and three screws
      1. Torque to: 17 inch lbs. (2 Nm)
    • Rear blower motor wire harness connector to the rear blower motor power module
    • Rear blower motor housing into the floor console
    • Four screws that secure the rear blower motor housing to the floor console base
      1. Torque to: 17 inch lbs. (2 Nm)
      2. Two console support brackets onto the floor console base
      3. Eight screws that secure the support brackets to the floor console base
        1. Torque to: 17 inch lbs. (2 Nm)
      4. Body wire harness bracket onto the console rear support bracket
      5. Body wire harness connectors to the rear blower motor power module and the rear mode door actuator
      6. Negative battery cable
      7. Front center floor console
  2. Calibrate the A/C-heater control.
prev.gif next.gif

Aug 13, 2010 | 2004 Chrysler Pacifica

1 Answer

How do you change a heater blower moter in a 1998 Dodge grand caravan


Removal & Installation


afab437.gif

The blower motor is located behind the glovebox, behind the blower motor cover

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.
  3. Remove the A/C-heater blower motor cover.
  4. Disconnect the blower motor wiring connector.
  5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  6. Remove the blower motor mounting screws.

b4976b0.gif
Once the cover is removed, unplug the electrical connector and push it through the opening in the housing


31d76b2.gif
The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

May 24, 2010 | 1998 Dodge Caravan

1 Answer

Starter solinoid replacement enstruction


SOLENOID REPLACEMENT
(see Figures 5, 6 and 7)

Prior to removing the solenoid from the starter motor unit, matchmark the solenoid-to-starter motor housing position, as shown in the accompanying illustration.
  1. Remove the starter motor from the vehicle.
  2. Detach the solenoid-to-starter motor wire from the solenoid terminal.

Do not disassemble the solenoid; if the solenoid is defective, replace the entire unit with a new one.
  1. Remove the two attaching screws, then slide the solenoid out of the starter motor housing flange.
9b9a219.jpg

Fig. 5: Before removing the starter motor solenoid, matchmark the solenoid-to-starter motor housing relationship

44d3238.jpg

Fig. 6: Disconnect the field coil lead from the solenoid by loosening the retaining nut ...

e357fdb.jpg

Fig. 7: ... then remove the two attaching screws and separate the solenoid from the motor housing


To install:
  1. Inspect the solenoid plunger joint for wear or other damage. Replace it, if damage is evident.
  2. Apply Suzuki Super Grease A (99000-25010) or equivalent, to the solenoid plunger and to the tip of the lever arm (inside the starter motor-to-solenoid housing hole).
  3. Insert the solenoid into the starter motor housing, ensuring that the matchmarks made during removal are aligned.
  4. Install and tighten the two attaching screws securely.
  5. Attach the starter motor-to-solenoid wire to the solenoid terminal.
  6. While the starter motor is removed form the vehicle, perform the testing procedure to ensure that the new solenoid functions properly.
  7. Install the starter motor.

Hope this help (remember rated and comment this).

Mar 23, 2010 | 1994 Geo Tracker

4 Answers

I need to replace a heater blower motor on a 2004 chrysler pacifica and picture schematics etc;


  1. Disconnect and isolate the negative battery cable.
  2. Remove the passenger side cowl trim panel. See: Body and Frame\Interior Moulding / Trim\Trim Panel\Service and Repair\Cowl Trim
  3. Pull back the carpet to access the front upper screw that secures the air inlet housing.
  4. Remove the recirculation door actuator.
  5. Remove the recirculation door actuator wire lead from the routing clip located on the lower air inlet housing and position the wire lead aside.
  6. Disconnect the blower motor wire lead connector from the blower motor resistor or power module, depending on application.

118348823 Lower Air Inlet Housing

  1. Remove the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing.
  2. Remove the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and remove the lower HVAC housing.

118348824 Blower Motor Wire Lead Grommet

  1. Push the rubber blower motor wire lead grommet through the opening in the lower air inlet housing.
  2. Feed the blower motor wire lead through the opening in the lower air inlet housing and remove the lower air inlet housing from the vehicle.
  3. Position the recirculation-air door as necessary to access and remove the three screws that secure the blower motor to the lower half of the HVAC housing.
  4. Gently flex the recirculation air door far down enough to remove the blower motor and wheel from the HVAC housing.

118348825 Blower Motor Mounting Tabs

  1. Remove the blower motor and wheel from the HVAC housing. Note the position of the blower motor mounting tabs.
INSTALLATION

  1. Position the blower motor and wheel to the lower half of the HVAC housing. Align the blower motor mounting tabs to the correct location on the HVAC housing.
  2. Gently flex the recirculation-air door far down enough to install the blower motor and
11_29_2011_6_18_00_pm.gif11_29_2011_6_18_20_pm.gif11_29_2011_6_18_40_pm.gif

Dec 02, 2009 | 2004 Chrysler Pacifica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...