Question about Cars & Trucks

1 Answer

Need to know code p0028 is making. Check engine. Light stay on and engine will not idle

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 47,608 Answers

Code p 0028 refers to intake valve control solenoid circuit , bank 2 ---range performance problem===causes--wiring ---intake valve control solenoid
this solenoid controls the advance / retard of the valve timing for the inlet valve camshaft and will account for the idle problem and the engine light
take it to an accredited service center who has experience on your make of vehicle and have the wiring checked or the solenoid replaced

Posted on Dec 01, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine light stays on while running, low idle


You need to have the pcm scanned for fault codes. If it is newer than a 1996 model, Autozone will scan it for free and tell you the fault codes. A mechanic would go from there, based on what the codes reveal. The low idle is probably a symptom of the fault.
Anytime the MIL light stays on with the engine running, the pcm (engine computer) has detected a fault and will turn the light on. It also stores a trouble code in memory, maybe called a pending code if only recently started, but the code can be found with a hand held scanner, hooked up to the port under the dash for code retrieval.
When you have done the repairs, and the old codes erased, you will see that the engine light always turns on when the key is turned on. If there are no more problems , the light will go out very quickly after the engine is running. It is a bulb and computer check that the light is on with key on, and stays on until the engine is started.

Nov 06, 2016 | Cars & Trucks

4 Answers

Cant seem to get the idle are timing locket in seem to idle to high the check engine light stays on


Find out what code the CEL is throwing. It could just be that your idle needs to be reset. Or you got the timing wrong when putting your car back together and it's running excessively hot.

Oct 15, 2014 | 1991 Honda Accord

1 Answer

Engine light on. Hard shift. Rough idle. Constant revving.


Check engine (MIL) lamp illuminated ??
Scanned/codes retrieved ??

Feb 09, 2014 | 1995 GMC Sierra

1 Answer

I have a 2001 Acura 3.5Rl and I want to know why my check engine light stats on after it's been reset? And is the idle sensor engine related? How much does it cost approx to repair idle sensor? Is it...


The check engine light comes on when there is a failure. If the failure is not fixed before clearing the codes than the computer turns the light back on because there is still a failure! In order for the light to stay off what ever is not working needs to be repaired. Then the codes can be cleared and the light will stay off. What code specifically do you have. It should be a P followed by four digits (P0128).

Apr 10, 2013 | Cars & Trucks

1 Answer

Where is the idle air control on a 2002 trailblazer? we have done a tone up it idles real bad at a stop dont have much power. check engine light flashes most the time, it will stay on for a short time an...


Truck should not be driven when the check engine light flashes, means you have something very wrong. Take it to a place like Autozone, they will check the code (check engine light) for free. There will be a code on the print out they give you, starts with Pxxxx. Let me know what the code is. What was done when you did the tune up?

Apr 15, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

Service engine soon light is on. Garage said they got a p0101 code. Engine idles OK but when throttle is applied engine starts to bog down and then the light starts to blink. If the throttle is reduced...


The code means there is a problem with the air mass sensor or circuit.
There are lots of possibilities, but the most common is that oil/water vapor foam from the PCV coats the air mass sensor and makes it inoperative. I suggest removing the sensor, cleaning it, and trying it again.
You can check it more accurately with an ohmmeter, but I don't know the normal reading range, and it should vary with air volume anyway.
But you can make sure it is not 0 or infinite ohms anyway.
Symptom is what you would expect, that the engine does not know you have applied throttle, and is still only giving idle amount of gas.
Perhaps a place like Autozone will check the air mass sensor if you bring it in.
If that is not it, then it is probably the control unit, with can also be brought in and tested.

Mar 11, 2011 | Chevrolet Tahoe Cars & Trucks

1 Answer

Check Engine light stays on /engine idles to fast


YOU MUST GET THE COMPUTER CODES FIRST TO SEE WHAT THE AREA TOO LOOK FOR COULD BE SIMPLE LIKE A VACUME HOSE/ INTAKE LEAK/ BAD MASS AIR METER . LOTS OF STUFF GO TO PARTS HOUSE MOST OF THEM OFFER FREE SCANS THEN REPOST YOUR CODES THEN WE CAN HELP

Aug 24, 2009 | 1999 Dodge Durango

1 Answer

I have a 1998 Plymouth Breeze 2.0. The check engine light came on and stayed on. And it started idleing real rough. Someone suggested I disconnect the battery and reconnect it to make the light go out. I...


Hi my name is Allen!

When the check engine light is on this means there is a problem somewhere in the powertrain control system, which could be almost anything.

Here is what I need you to do, drive your vehicle to AutoZone or another auto parts store near you and have them pull the codes for you. Then get back to me and let me know what those codes are, and what the scanner say the code means.

We will move further with repair procedure after I know what the code or codes are.

Waiting for your reply!

Jan 01, 2009 | 1998 Plymouth Breeze

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...