Question about Cars & Trucks

1 Answer

Replaced both cam sensors and crank sensor still getting poo17 code , timing chain seems tight is there a recognition procedure?

Posted by on

  • 1 more comment 
  • Jim Dec 01, 2016

    Hi Kevin Kauth, I want to help you with your question, but I need more information from you. Can you please add details in the comment box?
    Make, model & year of vehicle

  • jack layton
    jack layton Dec 01, 2016

    I agree with Jim, need more info, that is a correlation code.

  • Kevin Kauth
    Kevin Kauth Dec 02, 2016

    that woulda helped....its a 2012 hyundai sonata gls 2.4

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,630 Answers

What is the make, model year and engine type and size? Did you replace the connectors at the CPS sensors?

Posted on Dec 01, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: trouble code 1345 crank sensor/camshaft sensor correlation

I had this same P1345 code on my 1998 GMC K1500 5.7 for about 2 years. Each time the code was erased, the "Service Engine Light" came right back on with the same code. I tried replacing the cam sensor, but that didn't solve it. I had the timing adjusted, it was out -13 degrees. After adjustment, the "Service Engine Light" went off, but only for a short time. Adjusting the timing is just a temporary mask on fixing the real problem and eventually you will run out of adjustment. I read about this same problem on another forum and someone recommended changing the distributor gear. So I checked the gear and a the teeth were worn. Replaced the gear ($35 part), readjusted the timing and the light has been off ever since. Apparently the gears in 96-99 are soft and wear enough to throw off the timing. This code is telling you the crank and distributor are out of sync. So before you start buying sensors and other misc. parts, try the distributor gear if you are getting a P1345 code.

Posted on Mar 26, 2009

  • 137 Answers

SOURCE: 2003 stratus cam sensor replaced still unresolved

you bypassed the wires that connect to the sensors? that would have been my first guess the harness that plugs into the sensor. after that i would check the ground connection from the ecm. wouldn't hurt to check the battery posts too. if the battery posts are oxidized you can have all kinds of goofy electrical problems. hope that helps.

Posted on May 27, 2009

  • 145 Answers

SOURCE: CAM SENSOR ENGINE LIGHT. MAX RPM 2000 SOMTIMES

I seen this before first of all don't let the car dealer to BS the way to your money, most of the time is noting wrong whit the sensor it self but is the plug than goes in to the sensor this what i recommend is to buy another sensor from your local auto part store or salvage yard (cheaper) get three pieces of cable and solder directly in to the sensor brake the plastic around the sensor plug if necessary and secure the three cables to it put some silicon in between the solder and the place the new sensor on top of the old one so you now wish wire goes to which and cut and attach one by one. I now this works 100% i have done it my self many times if you need diagrams or sensor locations you can find that at www.alldatadiy.com now if you still have problems unplug all harness especially all the ones than comes from the back of the engine because that engine tends to leak oil on top of the harness if you have wires doing shortcut replace that section you can solder use heat string tube and change the insulation hose they sale those on part stores to put some zip tides on the ends and you will have your car back and will last Note don't let it get to close to the exhaust use zip tides to keep from touching hot areas.

Posted on Jun 10, 2009

  • 103 Answers

SOURCE: CAM SENSOR CODE P0340 SETTING

Hasw the magnet fallen off of the cam sproket ? If so, replace the entire set.

Posted on Jul 27, 2009

Zim1308
  • 543 Answers

SOURCE: car doesnt rev up

sounds ike it could be the Crank sensor, do you have the OBDII code off hand?

Posted on Mar 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What has to be done to eliminate recurrent DTC P1336?


The first thing you probably should do is get a copy of the shop manual for your year and model. The manual would have the actual test procedures for the code.
You probably know code 1336 means the signal from the cam and crank sensors is not aligned, meaning the cam timing is off as far as the engine computer can see.
It could have been one of the sensors, but you normally get another code for that sensor too. It could also be a timing chain problem, or a wiring problem going back to the computer.

Jan 19, 2016 | 2002 Ford Taurus

1 Answer

2011 Chevy Malibu lt. P0016 code. Replaced both cam sensor.and crank sensor still won't start


If you have the V6, they have a history of timing chain problems. The tensioner can go bad allowing the chain to rattle and jump time. This weill set the P0016 code since the cam and crank are not sync'ed and will result in a no-start condition.

Dec 06, 2015 | Cars & Trucks

1 Answer

Getting p0016 code


Crankshaft Position - Camshaft Position Correlation
What does this mean? OBD Code P0016refers to
The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position. The crankshaft sensor is part of the primary ignition system and functions as the "trigger". It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the Crank and Cam signals are out of time by a specific number of degrees, this P0016 code will set.
Symptoms Possible sumptoms of OBD code P0016
Malfunction Indicator Lamp (MIL) illumination The engine may run but with reduced performance The engine may crank but not start The engine may exhibit a rattle near the harmonic balancer indicating the tone ring is damaged The engine may start and run, but poorly
Causes Possible causes of OBD code P0016
Timing chain stretched, or timing belt skipped a tooth due to wear Misalignment of timing belt/chain Tone ring on crankshaft slipped/broken Tone ring on camshaft slipped/broken Bad crank sensor Bad cam sensor Damaged wiring to crank/cam sensor Timing belt/chain tensioner damaged
Possible Solutions First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.

Nov 05, 2015 | 2010 Jaguar XF

1 Answer

Car turns over but will not start


What's the code ? P0016 Crank/Camshaft Mis-align/sync. How many miles on the vehicle ? Ever have timing chains replaced ?

Oct 27, 2015 | 2004 Chrysler Concorde

1 Answer

Cx 7 mazda cel codes P0011 and P0016


Causes may include:
  • Timing chain stretched, or timing belt skipped a tooth due to wear
  • Misalignment of timing belt/chain
  • Tone ring on crankshaft slipped/broken
  • Tone ring on camshaft slipped/broken
  • Bad crank sensor
  • Bad cam sensor
  • Damaged wiring to crank/cam sensor
  • Timing belt/chain tensioner damaged
  1. First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
  2. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
  3. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck

Jan 24, 2014 | Cars & Trucks

1 Answer

I have a 2007 jeep patriot. It stalled at stop sign started ran rough. Parked came back drove it home ran u- scan code p0017 replaced crank and cam sensors still runs rough changed plugs were bad. I was...


code p0017 refers to crank/ cam oosition sensor bank 1 sensor B -correlation ===causes --wiring--CKP sensor--CMP sensor--mechanical fault.
It also refers to control modules, cooling fan--no signal===causes -- wiring--ECM.
If it has a timing chain then the the advice that it will not be the chain is good. So I suggest checking out the cam/ crank sensors and wiring

Oct 22, 2013 | 2008 Jeep Patriot

1 Answer

I replaced the camshaft position sensor P0340, now the OBD is reading a PO0016


Causes that bring up code P0016 may include:
  • Timing chain stretched, or timing belt skipped a tooth due to wear
  • Misalignment of timing belt/chain
  • Tone ring on crankshaft slipped/broken
  • Tone ring on camshaft slipped/broken
  • Bad crank sensor
  • Bad cam sensor
  • Damaged wiring to crank/cam sensor
  • Timing belt/chain tensioner damaged
  1. First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
  2. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
  3. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.
Hope this helps

Feb 06, 2012 | 2005 Chrysler PT Cruiser

1 Answer

I have a 91 olds Ninety eight regency elite Intermittently dies code 41 comes up cam sensor circut replaced cam sensor still dies could it be the crank sensor? thank you Michael Dale


cam sensor is only half of the cam circuit, the other half of the cam circuit is the magnet on the timing chain. the cam sensor reads from the magnet every time the engine completes a revolution,
what happens is the magnet on the chain will break into smaller piece which makes the sensor harder to read every time the engine make a complete revolution.
most likely you'll need to replace the timing chain to fix this.

Oct 12, 2009 | 1991 Oldsmobile Ninety Eight Regency

2 Answers

Cam & crank sensor code intermitten spark 2.4


are they the same engines? and i mean exactly the same? if the arent the same maybe check and look at the starter ring gear and count the teeth...also check the camshaft sprocket...is it different?

Oct 09, 2009 | Pontiac Sunfire Cars & Trucks

1 Answer

2003 caravan will not start!!!


Hi..
On your problem with the Caravan.

If you Have replaced the Crank and Cam sensors. And the Code Cam/Crank Correlation sensor.
Is found.
Normally this code is present When the Timing belt or Timing Chain, Is out of time 1 or more dents
On the timing due to Skip of the timing belt or Chain.

But don't forget check the connector at the sensors. For any damaged or corrosion on the pins.
Ok.. I hope this help to try diagnostic your car.

Thank you for use fixya.

Nov 03, 2008 | 2003 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...