Question about 1999 Toyota Avalon

1 Answer

Trying to find the location of the pressure oil sensor Toyota 1999 tacoma 6 cilin

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 850 Answers

It will be on the engine block near the oil filter usually

Posted on Jul 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is iat sensor on 2006 toyota tacoma 4.ol 4door located ?


This is the 2001-2012 Toyota Tacoma wiring diagram, Toyota Tacoma IAT (Intake Air Temperature) Sensor Location and the Toyota Tacoma MAF (Mass Air Flow) Sensor Location, also included is a pinout of the sensor. You are likely installing a performance chip or a cold air intake kit for increased HP (Horsepower). You will want to be sure to disconnect the car battery before adding performance products.




Here is the Toyota Tacoma's Iat sensor diagram:




ab0b7213-0c7f-459c-b26e-77a685236e74.jpg

Apr 14, 2015 | 2006 Toyota Tacoma

1 Answer

Can you tell me where the knock sensor is located on a 1998 toyota tacoma


depends on engine - dealer will tell u by serial #1.
help on net. however one is located left [to firewall from oil filter.
# 2 could be drivers side under intake manifold in the valley.
So unless want a big job look near the oil filter. oil dender is ahead of the filter..on the block.. But as I sead ask the parts department at a dealer..Good luck.. I had the wire drop off on my 89 3 liter v6 .was of roading just by the oil filter.. stick I guess.
cowcamp

Sep 20, 2014 | 1998 Toyota Tacoma

1 Answer

Where is knock sensor on a 2003 toyota tacoma


On a 4 cylinder it's located on the side of the block, driver's side on a V-6 engine there are two and are located under the intake manifold, it has to be removed to get to them.

Jul 27, 2014 | 2003 Toyota Tacoma

1 Answer

Oil pressure warning light does not lights.car running good.toyota sienna 1999 3.0 engine 6 cylinders


the light only comes on when the oil is low. to test it, next time you service it start the engine with a few quarts oil missing. it is safe for a short time, check the light

Apr 12, 2013 | 1995 Isuzu Trooper

1 Answer

Where is the starter relay for a 1999 Toyota Tacoma located?


hadder: in the engine compartment is a large box which contains fuses and relays. The starter relay is one of ones in the very rear(close to the firewall) It would be the second one in from the engine side and is a 5 pin relay. The same location applies for the four and V-6's.

Aug 12, 2011 | 1999 Toyota Tacoma PreRunner

2 Answers

My 1999 toyota tacoma prerunner ran fin oil light came on aqnd it just shut off


Maybe you are low on oil and some cars are made like that to shut off when they run out of oil. So check the oil level and add as needed. if there is oil then maybe the oil pressure is low

Dec 08, 2010 | 1999 Toyota Tacoma PreRunner

1 Answer

Location of the fuel filter on 2000 toyota tacoma 2 wd std cab


Oil filter on a 2000 Toyota Tacoma Prerunner with 6 cylinder IS a screw on filter located on the drivers side front of the engine (just beneath the alternator).

Can't recall the size but, you need a socket with extension to get to the bolts holding the skid pan then, wiggle/lift it from it's hooks. Then, you can either cuss, cuss, cuss while removing the old and installing the new OR, jack the drivers side up 4 to 6 inches ( gives you a bit more wiggle room and keeps you from scraping your elbow to the bone on whatever surface you're working on).

Even then, be ready for a good cussing bout because there still isn't much room.

May 19, 2010 | 2000 Toyota Tacoma PreRunner

1 Answer

I need the location of the coolant temerature sensor on a 99 taco


Its at the rear of the engine, close to the firewall. Look at the intake part of the engine block for 2 wires that connect into the sensor plug. It is installed vertically.

Dec 06, 2009 | 1999 Toyota Tacoma PreRunner

1 Answer

2006 Toyota Tacoma V6 engine oil sensor location


There is not enough flow at the sensor for a second oil filter. The sensor is at a dead end in the oil gallery. I recommend that you persue other options here. If you are concerned about oil contamination, don't be. There is nothing better than the factory filter...Look into adding more oil capacity; Look into an engine oil cooler; there is really no need for a second filter.

Sep 07, 2008 | 2006 Toyota Tacoma

Not finding what you are looking for?
1999 Toyota Avalon Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...