Question about 2001 Dodge Intrepid

1 Answer

I have a replacement flasher, but I can't locate where to install it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,776 Answers

It should be located in the front seating area, driver's side, under the left hand side of the instrument panel, between the junction box and the brake pedal. Sure hope this helped.

Posted on Jul 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LXI. how do I replace flasher?


The Flasher is located: Behind A/C and heater control panel, in center console.

Flashers

Print
REPLACEMENT

Flashers are located either on the bottom of the fuse block or on a module under the dashboard. They are replaced by simply pulling them straight out. Note that the prongs are arranged in such a way that the flasher must be properly oriented before attempting to install it. Turn the flasher until the orientation of the prongs is correct and simply push it firmly in until the prongs are fully engaged.clink on link to see what flasher look's like.
http://www.autozone.com/electrical-and-lighting/turn-signal-flasher/novita-turn-signal-flasher/chrysler/sebring/1998/4-cylinders-y-2-0l-mfi-dohc/193143_0_7283

Aug 15, 2015 | 1997 Chrysler Sebring

1 Answer

Where is the turn signal flasher located for a 2000 Nissan Quest


2000 Nissan/Datsun Truck Quest Mini Van 3.3L SFI 6cyl


Flashers

Print
The turn signal/hazard lamp flasher is located behind the driver's side of the instrument panel to the right of the steering column.on the fuse block
REPLACEMENT
  1. Disconnect the negative battery cable.
  2. Locate the flasher assembly under the driver's side of the instrument panel. Press the tab on the flasher and slide it from the bracket.
  3. Detach the flasher from the electrical connector and remove the flasher from the vehicle.
  4. The installation is the reverse of the removal.

Nov 04, 2013 | 2000 Nissan Quest

1 Answer

Chrysler 300M turn signals and flashers don't work


The Combination Flasher, also refered to as the combo-flasher, is mounted to the in-line bracket which is located to the right of the Junction Block. The Junction Block (JB) is located in the left endcap of the instrument panel. REMOVAL Open hood and disconnect the negative battery cable remote terminal from the remote battery post. Remove the left instrument panel silencer. Refer to Body Instrument Panel Silencer, REMOVAL. The flasher can be removed by pulling in a rearward direction. INSTALLATION Install the flasher by firmly pushing it into place. Install the left instrument panel silencer. Refer to Instrument Panel Silencer, INSTALLATION. Connect the negative battery cable remote terminal to the remote battery post.

Aug 06, 2012 | 2002 Chrysler 300M

1 Answer

The turn signals and emergency flashers do not work


replace flasher unit.
The turn signal and hazard flasher unit is located in the interior fuse panel located under the driver's left side knee protector. They are replaced by simply pulling them straight out. Note that the prongs are arranged in such a way that the flasher must be properly oriented before attempting to install it. Turn the flasher until the orientation of the prongs is correct and simply push it firmly in until the prongs are fully engaged.

looks like this:

jturcotte_0.jpg

Nov 04, 2010 | 1998 Mitsubishi Diamante

1 Answer

My turn signals don't flash


make sure all the bulbs are working. If not check the fuse but i doubt its a fuse cause none of the lights would be on but check the flasher. Flasher Location

It is located under the dash board on the drivers side. You will need a flash light, zip cord for re-installation, a long non metallic rod 1/4" dia and a wire hanger. Bend hanger straight and make a little hook on end. Remove turn signal fuse located at fuse box under driver side dash. Lay on floor with flashlight on drivers side. Look above fuse box it is located above it about 10" it is round and silver. Use rod to push off clamp. Now use hanger to retrieve flasher unclasp and install new flasher. Reinstall flasher and clip under dash with zip cord for access later. Replace fuse. If you need further assistance please let me know. Thanks, midwest-tek

Sep 17, 2010 | 1992 Buick LeSabre

1 Answer

Replace turn signal flasher


The flasher unit is located on the RH steering column opening reinforcement, and is attached by a bracket.

The combination turn signal and hazard flasher can be removed by pressing the plastic retaining clip (attached to the flasher housing) and pulling straight rearward. To install a new flasher, align the bracket with the track on the flasher housing. Then push the flasher forward until it snaps into the bracket.

Jun 03, 2010 | 1991 Ford Thunderbird

1 Answer

99 ford contour hazard flasher unit where is it


Flashers - REPLACEMENT

Turn Signal Flasher
(see Figure 1)

e21631a.jpg

Fig. 1: The turn signal flasher is located on the multi-function switch in the steering column
  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column shrouds.
  3. Pull the flasher from the back of the multi-function switch.

To install:
  1. Install a new flasher in the multi-function switch.
  2. Install the column shrouds.
  3. Connect the negative battery cable.

Hazard Warning Flasher
  1. Disconnect the negative battery cable.
  2. Remove the knee bolster panel from the underside of the driver's side of the instrument panel.
  3. Grasp and pull the flasher from the connector located near the top of the steering column.

To install:
  1. Install a new flasher in the connector.
  2. Install the knee bolster panel.
  3. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 02, 2010 | Ford Contour Cars & Trucks

1 Answer

Where is the flasher located in a 1999 Mercury Villager>


1999 Mercury Truck Villager Wagon 3.3L SFI SOHC 6cyl
Flashers
The turn signal/hazard lamp flasher is located behind the driver's side of the instrument panel to the right of the steering column.

REPLACEMENT
  1. Disconnect the negative battery cable.
  2. Locate the flasher assembly under the driver's side of the instrument panel. Press the tab on the flasher and slide it from the bracket.
  3. Detach the flasher from the electrical connector and remove the flasher from the vehicle.
  4. The installation is the reverse of the removal.
Hope help with this (remember rated and comment this).

Mar 13, 2010 | 1999 Mercury Villager

3 Answers

Where does the flasher go on a 98 chevy malibu


Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Dec 01, 2009 | 1998 Chevrolet Malibu

Not finding what you are looking for?
2001 Dodge Intrepid Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...