Question about 2003 Hyundai Accent

Open Question

Rear fog lamp removal

I need to remove the rear fog lamp to repair the bulb holder wiring connection. Any ideas on how the complete lamp is removed?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: how to replace bulb for fog on the front .

You can access it from behind.You have to remove splash shield and go from the underside.

Posted on Nov 29, 2008

  • 67 Answers

SOURCE: Fog Lamp Bulb Replacement, 05 Tucson

remove headlamp assembly and you can get it from the top pretty easy

Posted on Feb 26, 2009

  • 179 Answers

SOURCE: Fog Lamps on 2003 Pontiac Sunfire Not Working

check ground at fog lamps.

Posted on Mar 28, 2009

ghost4548
  • 776 Answers

SOURCE: Fog Light Bulb 2008 Elantra

Simple to do.

3624ae9.gif

5e693d8.gif

Posted on Jun 20, 2009

wizzer_W
  • 1 Answer

SOURCE: describe how to change fog lamp (just the bulb) on

2005 Forester - It is easiest to remove the fog assembly.

1. From underneath the vehicle pry out one plastic fastener to be able to bend the light weight plastic mud protector downward. You will see the underside of the fog light assembly with one 10mm bolt directly above you. Remove this bolt.
2. From the front of the vehicle unscrew one 10mm bolt at top of fog light (this is the shorter of the 2 by the way) and pry out one plastic rivet adjacent to it.

3. Carefully remove the fog assembly and disconnect 2-pin power connector by pulling up on the release. Carefully wiggle the housing out (no force req'd).
4. Unscrew the back from the housing and replace H3 bulbs. Take care not to touch the bulb while replacing.

5. Reverse to install.

Should take an hour at most.

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a car park lights


No idea what car you have
In most cases, unless you have a 20 year old
vehicle, you have to remove the lamp holder from
the body, then replace the bulb/lamp.
Again most come off from the outside using
Torx Bits & some on the rear by removing a few nuts
holding the lamp housing inside the trunk
On the front you got big problems as your hands don't fit
where they need to go to get to nuts.
If the lamps are down low on the front such as fog lamps
& a few parking lamps you crawl under the car & reach up
with a flash light & remove the lamp holder

Aug 08, 2013 | Cars & Trucks

1 Answer

How do I remove the rear brake light cover on 1990 GMC Sierra 2500 to change bulbs? Are there clips inside-specific places to pry it off? Thanks


seddy29732_3.jpg I hope these instructions match your model.


  1. Lower the tailgate.
  2. Remove the lamp assembly retaining screws.
  3. Pull the lamp assembly from the truck and disconnect the wiring.
  4. Remove the bulb holder fasteners.
  5. Remove the bulb(s) from the lamp.
  6. Install the bulb, connect the wiring and install the lamp.

seddy29732_4.jpgseddy29732_5.jpgseddy29732_6.jpg

Jun 03, 2011 | 1990 GMC Sierra

1 Answer

I need a detailed instructions on how to connect a toogle switch to a fuceable link to a battery and to a halogin headlight bulb?


Ok there are 2 ways todo this ,, the first is the easiest but not the cleanest..

First ..
1.) connect 8 guage wire from postive battery terminal to (2 port fuse holder)..
2.) from each of the fuse in the holder connect to the positive lead of each bulb (which should be in the bulb holder and in the headlamps or fogs or whatever).
3.) connect negative to a bolt on cars body.. Lamps will come on..
4.) remove positive from battery terminal..
5.) connect to your spst switch (what ever kind of switch u are using.)
6.) mount switch inside car,
7.) connect wire from other lead of switch to battery terminal..(pos)
Switch the lamps on and off using the switch..

Second method..

you will need
2 4-pin relays
8 guage wire
tester

1.) remove connectors from both head lamps
2.) turn on head lamps and test to see which is positive on each
3.) bridge this wire to the Com on the relay .. (1 head lamp to 1 relay)
connect positve wire from battery termial to relay (each relay seperate wire)
connect negative wire from cars body to relay (each relay seperate wire)
4.) connect Out from relay to Positive on Halogen bulb
6.) connect negative from bulb to cars body

now the lamps will come on and off with the head lamp switch..

Alternatively you can connect the fuse holder to the battery, and connect a switch to that and then that to the positive in on the relay..

Sorry I dont have any diagrams didnt have the time to draw one,, answered this quickly this morning before work..

Sep 08, 2010 | Lincoln Mark VIII Cars & Trucks

1 Answer

No revers lights


REMOVAL & INSTALLATION 1988–91 R/V Series
  1. Remove the lens-to-housing attaching screws. Remove the lens.
  2. Replace the bulb(s).
  3. Installation is the reverse of removal.
Except 1988–91 R/V Series Fig. 1: Remove the lamp assembly retaining screws 87986p17.jpg
Fig. 2: Pull the lamp assembly from the truck 87986p18.jpg
  1. Lower the tailgate.
  2. Remove the lamp assembly retaining screws.
  3. Pull the lamp assembly from the truck and disconnect the wiring.
  4. Remove the bulb holder fasteners.
  5. Remove the bulb(s) from the lamp.
  6. Install the bulb, connect the wiring and install the lamp. Fig. 3: Disengage the electrical connection 87986p19.jpg
    Fig. 4: Unfasten the bulb holder retainers 87986p20.jpg
    Fig. 5: Remove the bulb holder 87986p21.jpg
    Fig. 6: Pull this type of bulb from the socket 87986p22.jpg
prev.gif next.gif

Sep 03, 2010 | 1994 Chevrolet Suburban

1 Answer

I need to replace a foglamp bulb right side.I have fairly easy access to & can see the rubber housing for the bulb,but cannot figure out how to remove it.Do I need to rermove the entire assembly in...


Typically the fog lamp is located in the front bumper assembly. It's usually fairly easy to access and replace these.

Place the car is park, secure parking brake. Use a creeper to scoot under the front end of the car, look up into the bumper. Located the backside of the fog lamp holder. You would usually grab and twist counter clockwise about an inch, then pull straight out. Push in on the bulb while turning counter clockwise until it pulls out of the lamp holder.

These fog lamps usually have a little bit of cushioning grease in the socket. Do not remove the grease or connectivity problems will result with the new fog lamp. Push the new bulb in, turn clockwise until bulb stops turning, release hand pressure.

Installation is the reverse of removal.

May 25, 2010 | 1999 Oldsmobile Eighty Eight

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

3 Answers

Directions for replacing fog lamp bulb on 2005 hyundai xg350


first start by popping the hood then removing the gray caps covering ether the low beam or high beam depending on witch your replacing these are located on the right front by the battery and left front by the windshield fluid reserve then undo the metal clamp securing the bulb then carefully remove the bulb keeping in mint to only attempt this after the bulb has cool because they get extremely hot and never touch the bulb if you plan on using then again after that disconnect the wire harness from the bulb then take your new bulb and it will plug right in.WARNING HID BULBS WILL NOT WORK OR CONNECT PROPERLY IF YOU DON'T HAVE A COMPLETE HID KIT.

Aug 12, 2009 | Hyundai Motor 2005 XG350

1 Answer

Need a fuse box diagram to wire in fog lights


Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Aug 11, 2009 | 1995 Jeep Cherokee

1 Answer

How do you replace the fog light bulbs on a 2004 buick regal?


Notes FOG LAMP BULB REPLACEMENT - FRONT

REMOVAL PROCEDURE
f98bf40.gif
  1. Remove the front bumper fascia deflector.
  2. Disconnect the electrical connector from the front fog lamp bulb/socket. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
01c84b0.gif
  1. Rotate the front fog lamp bulb/socket counterclockwise to release.
  2. Remove the fog lamp bulb/socket from the front fog lamp assembly.
4065803.gif


  1. Install the fog lamp bulb/socket to the fog lamp rotating clockwise until fully seated. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
b182709.gif
  1. Connect the electrical connector to the front fog lamp bulb/socket.
  2. Install the front bumper fascia deflector.

Jun 16, 2009 | Buick Regal Cars & Trucks

1 Answer

HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Jul 28, 2008 | 1994 Chrysler New Yorker

Not finding what you are looking for?
2003 Hyundai Accent Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...