Right Indicator is frozen 'on'

I would think its a flasher relay or switch problem, do the indicators work when used via the stalk switch ? if they do then I'd start with the hazard switch

The AU ford has two indicator relays , turning lights and hazard lights ,both use the indicator lights ,the hazards flash both front and rear lights , the turning indicator flashes one front and one rear light. I think the fault may be in the hazard circuit.

There could be many things that can cause this. Could be the bulb sockets or fuse box.Hondas typically have a light module located behind the glove box . As well could be as simple as a ground cable or bad alarm or command start if applicable to your vehichle.

CHECK THE FUSE BOX FOR blown flasher fuse. Dont think thats it but its 1st step. I think it is a bad flasher switch, if its not the fuse. Replace the switch. mike

flasher relay under steering column does not work,switched it with hazard and see if it works,then get the new one,make sure the light on turn signal in front or back is not burned out first

if you have trouble with your indicators or hazard lights change the hazard light switch get one on ebay.

The left/right indicator relay and hazard light relay is one unit built into the hazard light switch in the dash

Replacement

1. Access the fuse panel from the left of the steering column.
2. Locate the blown fuse and pull out. DO NOT TWIST.
3. Take note of the ampre number written on the top of the fuse. To install:
   
4. Push a new fuse of the same ampre into the receptacle, making sure the contact is being made on both sides of the fuse.

LOCATIONS Headlights and Highbeam Indicator

• One 18 amp circuit breaker (22 amp in 1987 vehicles) incorporated in the lighting switch.

Front and Rear Marker, Side Parking, Rear and License Lamps

• One 15 amp circuit breaker incorporated in the lighting switch.

Windshield Wiper

• One 4 1⁄2 amp circuit breaker located in the windshield wiper switch.

Power Windows

• Two 20 amp circuit breakers located in the starter relay and the fuse block.

Power Seats and Power Door Locks

• One 20 amp circuit breaker located in the fuse block.

Hazard Flasher REMOVAL & INSTALLATION NOTE: The hazard warning flasher is located on the rear side of the fuse panel.

1. Locate the hazard flasher in the fuse panel.
2. Pull the flasher out. DO NOT TWIST. To install:
   
3. Push new flasher into place making sure a good contact is made with both terminals.
4. Test flasher to make sure they function properly.

Various Relays LOCATION Cooling Fan Controller

• Located behind the left side of the instrument panel.

Cooling Fan Controller Module

• Located behind the right side of the instrument panel.

Cooling Fan Relay

• Located in the air conditioning cooling fan control module.

Electronic Control Assembly

• Located under the left side of the instrument panel.

Electronic Engine Control Power Relay

• Located behind the glove box on the right side of the instrument panel.

Fuel Pump Relay

• Located behind the glove box.

Horn Relay

• Located in the fuse block.

Fig. 1: Main fuse box located on driver's side to the left of the steering wheel, above the brake pedal


This is the best info I could find....I hope this helps ya!

Indicator Flasher The turn signals and the hazard warning flasher switch (13A350) use the same indicator flasher (13350). The indicator flasher is located behind the instrument panel (04320), to the right of the interior fuse junction panel. When activated, the indicator flasher flashes the appropriate turn signal lamps.

Removal

1. Disconnect the battery ground cable (14301).
   

1. Press the indicator flasher tab and slide the indicator flasher from the mounting bracket.
   

1. Disconnect the indicator flasher electrical connector from the wiring harness.
   

try playing with the hazard switch if hazards work and indicators dont work then change the hazard switch.If none are working then indicator unit is behind the cover on steering column in the back of the indicator switch,but remember models can change builds for rhd and lhd,if its not their then its on the back of the fuse box ,their is a clip that allows it to drop down allowing access.