Question about Hyundai Excel

1 Answer

The front disc brakes have 3 bolts that prevent me from putting on new rims. Are there certain manufacturers that can handle this problem. I understand the newer Hyundai's dont have the three bolt. What are my choices? What rims can I use on this vehicle?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 207 Answers

You need to go to a tire shop and look at the universal style rims they have rims that will fit your car you bascily just need to get some flyers and look up universal hub types they have a bunch to chose from like i said a tire shop should have the flyers good luck

Posted on Jul 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front disc brake installation


Brake discs with pads need to be changed both sides on the same axle. Slacken the lug nuts and then lift the corner of the car and remove the wheel. Put a screwdriver tip between the brake pad and the disc and twist until a couple of millimeters of gap has opened up, do this front and back of the disc. Now remove the two large caliper securing bolts and lift the caliper up. locate the caliper body so that its weight does not pull on the rubber brake hose ( piece of wire to hold it temporarily to the strut spring is good). The disc is located by a couple of small screws. Remove these and the disc will come off the wheel studs. Fit the new disc and reinstate by reversing the steps above. Note if you have pushed the pads back far enough when removing the calipers then the caliper should refit easily over the unworn and therefore fatter new disc even with new pads fitted. put a small dab of anti-seaze grease (CopperEaze or similar) on the back of each pad as this will prevent squeal. Tighten the caliper bolts thoroughly when reassembling. Remember to pump the brake peddle back to pressure to re-seat the new pads to discs before test driving. Now do the same to the other side. If you are new to this the fist wheel is a voyage of discovery and the second wheel will take a quarter of the time.

May 12, 2011 | 2004 Jaguar X-Type

Tip

How to Change Your Brake Pads


Brake Pads should be replaced in pairs, the front will wear faster than the rear so usually the front will need to be replaced more often.
First Here is a list of what you will need. This list mainly applies to disc brakes but I have included a link for how to replace drum brakes with graphic images. All parts can be purchased from an auto parts or hardware store.
  • New Brake Pads
  • C-Clamp
  • Small amount of Brake/Caliper Grease (usually comes in a small packet)
  • A can of Brake Cleaner
  • Car-jack and lug wrench
  • A small bungee cord
  • Wrench/Socket/Allen Wrench (depending on your car)
  • A hammer (mainly for drum brakes)
  1. Lossen the lug nuts.
  2. Jack up the vehicle.
  3. Remove the tire from the vehicle.
  4. Use the brake cleaner to spray the brake pads and disc taking care not to spray plastic parts on the vehicle. This is done to partly protect yourself from the brake dust and to also clean everything and help remove rust.
  5. The following steps are for disc brakes, for drum brakes skip to step 15.
  6. Next, remove the caliper bolts, the heads will be located on the inside side of the caliper, the wrench needed will vary base on vehicle make and model.
  7. Slide the caliper and brake pads off of the disc.
  8. Remove the outer brake pad.
  9. The bungee cord may be used to keep the caliper from hanging freely. Do not allow the brake line to be bent or hold the caliper itself.
  10. Use the C-Clamp to slowly depress the inner brake pad as far as it can go. If any brake fluid leaks out of the reservoir, it may need to be replaced once brakes are replaced. Make sure to press the brake pedal several times between each tire having brakes replaced to help keep brake fluid from leaking. Some brake fluid may be siphoned beforehand to prevent loosing any fluid.
  11. If the disc is to be replaced, do so now, spray the new disc with brake cleaner to remove any residue. The disc should be replaced if grooves or chips are found on it, or if it is outside of thickness specifications of the manufacturer.
  12. Grease the caliper bolts.
  13. Put the new brake pads on the caliper and slide the brake pads and caliper back onto the disc and insert the bolts.
  14. Skip to Step 18 for disc brakes.
  15. For drum brakes, use the hammer, brake cleaner, and possibly a pry bar to remove the drum which should slide directly off.
  16. Use the brake cleaner to spray the brake pads and other parts within the drum to clean and prevent dust from being breathed in.
  17. Use the following link for better information on how to replace drum brakes http://www.2carpros.com/articles/how-to-replace-rear-brake-shoes-and-drums
  18. Mount the tire, bolt on the lug nuts, and remove the jack.
  19. Press the brake a few times and clean up.
Congrats on replacing the brake pads on your vehicle.
Benjamin

on Jan 06, 2011 | Dodge Intrepid Cars & Trucks

2 Answers

I have an 2006 Hyundai Accent Atlantic and I would like to know if front brakes have pads and rear brakes have shoes


2006 Accent Brakes, Suspension & Handling Specs • Four-wheel ABS • Four disc brakes including two ventilated discs • Electronic brake distribution • Spacesaver steel rim internal spare wheel • Strut front suspension independent with stabilizer bar and coil springs , torsion beam rear suspension semi-independent with stabilizer bar and coil springs

Read more: http://www.automotive.com/2006/12/hyundai/accent/specifications/handling-ride-braking.html#ixzz1JcYuzhff

Apr 15, 2011 | 2006 Hyundai Accent

1 Answer

How to replace disc brake pads?


JACK THE WHEEL UP, AND TAKE TIRE AND RIM OFF! YOU'LL SEE THE DISK BRAKE CALIPER! ON THE BACK OF THE CALIPER IS TWO BOLTS (POSSIBLY ALLEN HEAD BOLTS) REMOVE THOSE TWO BOLTS, AND WIGGLE THE CALIPER! YOU'LL NEED TO SPREAD THE CYLINDER INSIDE WIDER TO ACCOMODATE FOR THE NEW BRAKE THICKNESS! YOU CAN DO THIS BY LOOSENING THE ZERK FITTING JUST ENOUGH TO PUSH THE CYLINDER IN WITHOUT LOSING ALL THE BRAKE FLUID! SET THE BRAKEPADS IN THE SAME POSITION AS THE OLD ONES COME OUT! PUT THE CALIPER BACK ON THE HUB, AND PUT THE BOLTS BACK IN! TIGHTEN THEM BACK DOWN, AND PUT THE WHEEL BACK ON!

Feb 26, 2011 | 2000 Oldsmobile Alero

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

How do you get the capierer pin off to put front brake pads on my Mercury Sable LS?


Section 06-03: Brakes, Front Disc 1999 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478) . Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120) , front disc brake rotor shield (2K004) or front wheel knuckle (3K185) .
  1. Remove rear brake pin retainers (2N386).
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125) . Do not pry directly against metal caliper piston or damage will occur.
  1. NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .

    Position disc brake caliper out of the way.
  1. Remove inner outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate .
  1. Inspect both rotor braking surfaces. Minor scoring or buildup of lining material does not require machining or replacement of front disc brake rotor.
-----------------------------------------------------------------
remove the 2 pins, #10 in pic. Usually has a dust cover over pin accessopening. Usually torx haed or hex head bolts (pins).


snorkelbobby_7.gif

Nov 12, 2010 | 1999 Mercury Sable

2 Answers

Change back Brake pads on renualt megane 2


1. Hand Brake ON , loosen wheel bolts to hand tight, jack up front wheel , chock back wheels , put axle stands/blocks in place (just in case) .

2. Remove wheel. Disconnect pad wear wire , it pulls out of the connector.

3. Remove lower caliper bolt (at the back of caliper at the bottom) , need a 13mm ring spanner for head of bolt and 17mm to stop it spinning

4. Use a screw driver between the back of the outer pad and the caliper to prise the caliper back away from the back of outer pad. Pivot caliper upwards to rest on top of wheel disc (good idea to tie it up with some wire) .

5. Remove and discard old pads , clean out with wire brush and soft brush , don't breath in to much of the dust its nasty.

6. Fit new pads (remember pad wear sensor on inside pad), make sure that the pads are in contact with the disc , and the top of them sitting flush with the rim of the disc, don't force them into this position they should naturally sit there.

7. Lower caliper down into position, you may need to push back the piston further in order to make room for the new pads , do this with you hands or a small piece of timber. Keep an eye on the brake fluid resivoir , your pushing fluid back in so if its over full it may spill over. Refit lower caliper bolt (Renault say to replace this each time), and tigthen. Reconect pad wear sensor.

8. Pump brake pedal until normal brake pressure returns.

9. Remove axle stand/blocks , refit wheel and bolts , lower jack and tighten up wheel bolts.

Sep 18, 2009 | 2006 Renault Le Car

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

2 Answers

I can't find the right nuts and bolts to remove in order to replace the front brake pads on my 1990 GMC Sierra


you will need a big c-clamp to compress the piston back inside the caliper too when you remove your old pads. Otherwise you will never get the new ones to fit over the disc.

May 06, 2009 | 1990 GMC Sierra

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...