Question about 1999 Suzuki Grand Vitara

1 Answer

2000 grand vatara front hubs wont lock in shows locked in on the

2000 grand vatara front hubs wont lock in

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,071 Answers

Hub seals are bad or vacuum hoses rotten

Posted on Jul 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 suzuki grand vatara hatch door will not open?


nor with key? metal key in lock cylinder
the latch has two methods to unlatch.
  1. electric solenoid
  2. and pure mech. key cylinder
if both fail,, the latch is bad.
is it full of ICE, ITS 8OF HERE.
but there,????
the lock can be unlocked from inside, 3 ways
defeat the child blocks,(read operators guide)
then key fob, button
and last remove inside door skins, and operator the unluck lever
on side of latch by hand.
did i get them all?

Jan 07, 2015 | 2005 Suzuki Grand Vitara

1 Answer

How to replace front wheel bearing?


old post, but you are first to say front. many others fail to say end of car.

is your car 4wd, as 2wd is different rules. so...??????

I toss coin land on 4WD.

2000 front wheel bearing

got it.

the 2000 year, is important.

this year is the last year, before non untized hubs.

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer



my posts is for stock cars. only, and USA spec, cars.

other countries, evolve this in different years.



2000 (never 2001+)

fsm quotes



  1. Before servicing the vehicle, refer to the Precautions section.


  2. Remove or disconnect the following:



    • Front wheel


    • Brake caliper and rotor


    • Locking hub or hub drive flange, if equipped,(it is)


    • Hub grease cap, if equipped


    • Wheel speed sensor, if equipped (ABS)


    • Wheel bearing lockwasher


    • Wheel bearing locknut (ring) and inner washer


    • Wheel hub and bearing assembly (slide hammer?)


    • Wheel hub oil seal


    • Wheel bearing oil seal


    • Snapring




  3. Press the wheel bearing and race out of the hub.


reverse is same but the lock ring must be set

to 123-180PSI. stop tightening above 123 at first alignment hole in lock ring..

Jun 26, 2014 | 2000 Suzuki Grand Vitara

3 Answers

Front end will not lock in in 4x4 transfer case is in & dash lite shows 4x4 but front wheels don;t lock in.


Hi

It could just be low fluid in the gearbox/transfer box have you checked these?

Is the car new to you?

Jan 22, 2010 | 1999 Kia Sportage

1 Answer

4wd not engaging


Hi,

I have a 2000 Sportage EX, had the same trouble.

The 4wd works by Vacuum lines(rubber hoses) that uses air to lock the front hubs in.

Usually the rubber hose line behind the front tires at hub to the frame become dry rot,cracked---replace them and try it.

If hoses still good or replaced and still not working----there is a Vacuum pump under the hood near brake master cylinder(driver side on inner fender near windshield)---It looks like the size of a "D" flashlight battery with hoses attached and a single wire connected to bottom of it----sometimes these little pumps go bad too.

Other than that the Front hubs(automatic) might be bad(like a leaky air bag that wont inflate to lock hubs)---this can be a costly replace.

One last resort to avoid all this hassle----get a manual "WARN" locking hubs put on car(about $150)---this way you can lock the hubs manually by a 1/4 turn slot at each front tire to go in 4wd when needed.

Good luck---hope this helps.



Jan 19, 2010 | 2000 Kia Sportage

2 Answers

I have a 2000 4wd tacoma with manual locking hubs and the 4wd does not seem to be engaging after locking the hubs and shifting the lever into 4 hi or 4 low


Sounds like one of your hubs is sticking and not engaging. You can check them by engaging the hubs and the transfer case and jacking up each front wheel independently if it doesn't spin your good, if it does you found your problem. As far as fixing a hub goes, it may be just dry and need some grease, or there are some very good aftermarket hubs available from Warn.
Hope this helps

Dec 08, 2009 | 2001 Toyota Tacoma

1 Answer

Front hub to lock in to 4 wheel drive is locked and wont move. 2000 ford excursion v10 on one side only, is this a ford only part?? thanks


This is common. the locks due tend to freeze up and need either a greasing or replacement. I do suggest automatic locking hubs that you don't have to turn yourself. You can get the part almost anywhere

Sep 30, 2009 | 2000 Ford Excursion

1 Answer

Front hubs wont engage


There are two parts to the auto-locking hubs. Inner and outer. Both of them have small tabs on each of the 'cams'. Chances are, they are broken off on the outer hub. When you clean them up real good, you can see them. I believe when the axles turn the outer hub, the inner and outer cams push against spring pressure and lock the unit to the wheel hub. These hubs will break when engaged at higher speeds, especially on a dry tar road.

Jan 11, 2009 | 1991 Ford Explorer

1 Answer

Ford 4x4 frint wheels wont engage


if you look there is probably only one axle shaft turning also that shaft should not turn unless the wheels are there is probably something wrong with that hub not a big problem to tear down and check you can also get replacement hubs that are manual locking.

Dec 30, 2008 | 2003 Ford F150 Regular Cab

2 Answers

Front hubs sticking in locked position need to rebuild, How to and any suggested parts for replacement


replace your auto/lock hubs with WARN manual lock hubs,this will save you hunderds.as long as you dont mind having to get out to lock in. NAPA.

Oct 18, 2008 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
1999 Suzuki Grand Vitara Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...