Question about 2002 Chevrolet Blazer

1 Answer

Windshield washer fluid motor

Where is this pump located under the hood

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 144 Answers

Its in the bottom of your windsheild washer tank

Posted on Jul 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

1 Answer

In my 2007 Saturn Vue there is what I think is an air pump which is cracked that one port is not connected to anything.


There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Nov 18, 2016 | Saturn Cars & Trucks

2 Answers

Where is the windshield washer pump located under the hood?


it locate in tthe bottom of windshield water reservoir(tank)

Mar 04, 2015 | Chrysler PT Cruiser Cars & Trucks

2 Answers

2002 f350 7.3L. Windshield washer pump not working......Under dash fuses are fine. I read something about a relay under the hood? And is the pump motor located on or near the washer fluid reservoir? I'm...


There isn't a relay. The motor is attached to the side of the reservoir, near the bottom. You will most likely have to remove the tire and the inner fender well to get to it. Before you replace the motor. Use a volt meter and check for power and to the plug. You only have power when the switch is engaged.

Nov 03, 2014 | Cars & Trucks

1 Answer

WHERE IS BLOWER MOTOR FOR 2002 GRAND PRIX PONTIAC I ONLY HAVE THE HIGH SPEED #5 WORKING. ALSO IS THE WINDSHIELD WIPER SOLUTION MOTOR AT THE BOTTOM OF THE RESERVOIR BOTTLE, I CANT GET ANY SOULUTION TO...


Not super familiar with this model, but here's what I know:
Usually when only the high speed (#5 like you said) works, you need a blower motor resitor. That is usually located under the passenger side dash, under the glove box.
The washer fluid pump is sometimes located under the hood, close to the winsheild, sometimes mounted on the firewall.
Hope this helps!

Jul 12, 2011 | Pontiac Grand Prix Cars & Trucks

1 Answer

Windshield washer fluid barely sprays then quits. Does not spran on rear window at all. Good fuse and can hear motor running. 2006 kia sorento


windshield washer hose could have a hole somewhere have some one run washer pump while you check under hood for leaks if you cant find any then its safe to assume that pump is worn out still turns but the pump suction is worn out, must be replaced.

Jan 14, 2010 | 2006 Kia Sorento

2 Answers

Windshield washer isn't pushing out any fluid


Had that happen to me before. Simply raise the hood and locate the plastic or rubber tube running to out put nozzle on hood. Disconnect and see if fluid shoots out. If it shoots out, simple take a needle of safety pin and clean out the nozzles located on the hood and should work. To clean the nozzle, you will have to lower the hood. If you want to you can do that before raising the hood. Oh by the way I assume you have verified that the reservoir is full.

Rolling98

Jan 02, 2010 | 1989 Plymouth Voyager

2 Answers

I have a 1998 chrysler concord and i can get windsheild washer fluid to spray the resevoir is full no fluid is leaking out the wipers activate upon initiating the spray sequence but no fluid comes out


Pull out the small tube connected to the jet the fluid comes out of and check for any kind of debris, after blowing out the tube try and activate washer before you connect the hose again if no fluid comes out of the tube than that replace the small pump connected to the resivoir thay are about $15.00

Nov 29, 2009 | 1998 Chrysler Concorde

1 Answer

Hi, We have a 2004 saturn ion and we need to cahnge the windshield washer transmission and can't figur out how to remove the wipers, without bending the arm. Is there a easy way to do it?


The wiper "motor" is usually located at the bottom of the fluid reservoir. Remove the fluid bottle under the hood and at the lower end of it you will find the motor. Once in a while it is located on the wall of the car under the hood - follow your fluid tubes to find and replace.

Jan 07, 2009 | Saturn Ion Cars & Trucks

Not finding what you are looking for?
2002 Chevrolet Blazer Logo

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...