Question about 2000 Dodge Neon

1 Answer

Were would the restart button be located

Replaced the ignition switch still wont turn over,what about a restart button

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

I am sorry it does not have one:)

Posted on Jul 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1981 Bronco ignition key wont turn


make sure the shifter solenoid is engaging and disengag
ing properly

Mar 01, 2014 | Cars & Trucks

1 Answer

Remove ignition switch


Having the replacement switch you tell you a lot having a active key to turn to on position with help you depress the button on the switch in order to release the switch from the housing removing the any covering around the ignition might be required as well in order to get to the release button located on switch. Again your new switch will aid in this

Jan 15, 2014 | 1992 Lexus Ls 400

1 Answer

Relay switch


Ignition and Start Switch Replacement
Removal Procedure
2c23f8d.jpg Disconnect the battery ground cable. .
Remove the steering column filler panel.
Remove the knee bolster bracket.
Remove the instrument panel (I/P) cluster trim panel.
Remove the ignition switch bolts.
Lower the ignition switch away from the instrument carrier.
Insert the key into the ignition lock cylinder. Turn the key to the ON/RUN position.
Depress the transaxle park/lock cable retainer to release. Pull to remove the park/lock cable from the ignition switch.
Important: The Passlock? electrical connector cannot be removed until the lock cylinder is removed.

Depress and hold the detent on the bottom of the ignition switch in order to release the ignition lock cylinder. Remove the ignition lock cylinder with the key.
d857e46.jpg Disconnect the Passlock? electrical connector.
Disconnect the electrical connectors.
4093e3a.jpg Important: Ignition switch lock cylinder that won't rotate or is seized.

Perform the following procedure if the ignition switch lock cylinder is seized or won't rotate.
12.1. Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.

12.2. Locate the surface for the ignition switch lock cylinder release button (2) on the plastic ignition switch housing and center punch a location (1) on the "rib" approximately 3/8 inch reward (toward the key entry end) from the cylinder release button.

12.3. Carefully drill a hole through the plastic housing with a 1/8 inch drill bit.

12.4. Carefully drill a larger hole at the pilot location, and slightly into the ignition switch lock cylinder surface to break the release button retaining spring using a 9/32 inch drill bit.

12.5. Remove portions of the broken spring from the hole using a small suitable tool.

12.6. Grasp the ignition switch lock cylinder and remove it from the switch housing.

12.7. Remove any plastic "flash" from the drilling operation, and using compressed air blow out the ignition switch assembly.

12.8. Follow service manual procedures when cylinder cording is required. Refer to Key and Lock Cylinder Coding in General Information.

Installation Procedure
If the lock cylinder would not rotate or was seized, perform the following procedure:
1.1. Install the new ignition switch lock cylinder as required by rotating both the cylinder and the ignition switch to the ON position.

1.2. Push the ignition switch lock cylinder into the ignition switch housing until fully seated.

1.3. You may have to slightly depress the release button as the button passes by the 9/32-in hole previously drilled in the ignition switch housing.
9600af8.jpg Connect the electrical connectors.
Connect the Passlock? electrical connector.
Connect the park/lock cable to the ignition switchdd765ba.jpg Turn the key to the ON/RUN position. Install the ignition lock cylinder into the ignition switch. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
Remove the key
681874a.jpg Position the ignition switch to the instrument carrier.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Install the ignition switch bolts.
Tighten

Tighten the bolts to 10 N?m (89 lb in).

Install the trim plate bezel to the I/P cluster. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Install the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Install the steering column filler panel. Refer to Steering Column Filler Replacement .
Connect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.

Dec 05, 2013 | 2005 Chevrolet Impala

1 Answer

How do i reset service g maintenace light on 2003 E500 mercedes benz


nstructions
    • 1 Sit in the driver side seat and ensure that all the vehicle doors are closed.
    • 2 Switch the ignition to the "On" position, but do not turn the vehicle on.
    • 3 Press the "0" button located on the left-hand side of your dashboard twice, within four seconds of switching the ignition to the "On" position.
    • 4 Turn the ignition to the "Off" position, press and hold the "0" button while turning the ignition back to the "On" position.
    • 5 Continue holding the "0" for 10 seconds, or until the dash display on your vehicle reads "Service In."
    • 6 Turn the ignition off and restart the vehicle to verify that the service interval message is cleared from the system.

Read more: How to Reset the Service Light on a Mercedes E500 ' eHow.com http://www.ehow.com/how_7426320_reset-service-light-mercedes-e500.html#ixzz2QosrxBFW

Apr 18, 2013 | 2006 Toyota Corolla

2 Answers

Crankup and drive get some place and shut it off them sometimes wont restart till it cools. checked relays battery alternater all is good what is wrong ?


If your starter won't turn over after driving and shutting the car off, sometimes, it sounds like your starter is getting stuck/overheating. Replace your starter and this problem should go away.

Oct 08, 2011 | 2003 Saturn ION

1 Answer

My bronco2 wont start. Just replaced both fuel pumps, fuel filter, battery, fuel injector modal, I've tried to locate the restart button, think i've found it but it was broke. What do i do now or what is...


starter if engine wont crank....otherwise if it turns over but no start then it could be electrical maybe ignition module.if starter no work tap with hammer while trying to start they get hung up or on a flat spot an that usually jars them free...try electrical first pull one spark plug and see if when you trun it over the spark jumps the plug if it does then it is a fuel problem...dont hold spark plug wire position it to lay away fro everything...nobody likes gettin shocked no matter how funny it is after.....

Mar 19, 2011 | Ford Bronco II Cars & Trucks

1 Answer

HAVE 92 BONNY RUNS GREAT BUT DIES SUDDENLY AND WONT RESTART RIGHT AWAY. CAR TURNS OVER BUT NO FIRE THIS HAS BEEN VERIFIED REPLACED CRANKSHAFT SENSOR CHECKED ALL CHASSIS GROUNDS. IGNITION WAS RECENTLY...


If by 'no fire' you mean no spark, check all of your fuses, and have the ignition module (located under the coil packs) checked. Autozone can usually check the ignition module for free. If it has spark, it could also be the fuel pump going out.

Nov 18, 2010 | 1992 Pontiac Bonneville

2 Answers

No gas or spark


Try your inertia switch in the cargo area in back. Its located on the passenger side rear wheel well. Push the button.
2_27_2012_8_29_26_am.gif

Sep 23, 2009 | 1994 Ford Escort

2 Answers

My 1994 Mazda b3000 p/u died on me while i was driving. Has gas, new filter, and does crank but wont start. Need help


Does the electric fuel pump come on when you turn the key? It should make a buzzing noise for 3 seconds or so.

Jan 22, 2009 | Mazda B3000 Cars & Trucks

1 Answer

I have a 1991 Honda and the key will not turn in the ignition


you need to replace the ignition switch- most cars run around $25. they are fairly simple to replace.
remove the shroud that covers the steering wheel, turn the key to ACC, using a small flat head screwdriver, press the release button- usually located on the top right side, the switch should pull out with no problem. make sure the new switch is turned to ACC, and slide it in the slot, make sure the new switch works before you reassemble everything.

Nov 25, 2008 | 1991 Honda Civic

Not finding what you are looking for?
2000 Dodge Neon Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...