Question about 2002 Ford Explorer

1 Answer

How do i remove the rear hub on 2002 ford explorer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,776 Answers

Go to autozone's website at autozone.com and register your vehicle. It's free and you will have access to a full online repair manual for your vehicle. It will have the info you are looking for. Hope this helped.

Posted on Jul 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the easiest way to remove the rear hub on a 2005 Ford Explorer?


you need a hub wrench where the drive tangs engage the four slots in the hub nut and remove the nut.go to auto parts stores they carry hub wrench you also need 3 jaw puller loosen the rear hub to point of removal.

Nov 16, 2011 | 1999 Ford Expedition

1 Answer

Need to know how to get to the emergency brake on an 2002 ford explorer behind the disk brake.(rear driver side)


First remove caliper slider assembly & caliper. Will need to probably spray penetrating oil around rotor hub. Hit rotor on side of hub with sledge hammer & it will slide off. Inside are your emergency brake shoes.

Oct 20, 2010 | 2002 Ford Explorer

1 Answer

2002 ford explorer jerking


There are quite a few things to check here like the rear axle pinion bearing preload and all the wheel hub bearings. The best they you can do is run it while on a rack in 4wd and listen to it from underneith the vehicle.

Mar 23, 2010 | 2002 Ford Explorer

1 Answer

2002 ford explorer rear wheel bearing removal


Rear Wheel Bearing
REMOVAL AND INSTALLATION

1. Remove the wheel knuckle.

Wheel Knuckle
REMOVAL AND INSTALLATION

CAUTION: Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied.

1. Remove the wheel and tire assembly.

NOTE: Have an assistant press the brake pedal to keep the axle from turning.

2. Remove the nut and washer and discard the nut.

3. Remove the parking brake shoes.

CAUTION: Do not damage the boot while separating the toe link from the knuckle.

4. Remove the nut and bolt and separate the toe link from the wheel knuckle and discard the nut.

CAUTION: Do not damage the boot while separating the ball joint from the knuckle.

5. Remove the nut and bolt and separate the upper ball joint from the wheel knuckle and discard the nut.

CAUTION: Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.

6. Using the special tool, press the outboard CV joint until it is loose from the hub.

7. Remove the nut and bolt and the wheel knuckle, hub and bearing as an assembly and discard the nut.

(Return to)
Rear Wheel Bearing
REMOVAL AND INSTALLATION

2. Remove the three bolts.

CAUTION: Make sure that the press adapter outside diameter is slightly smaller than the hub outside diameter or damage to the knuckle will result.

3. Using a suitable press, remove the hub from the bearing and discard the hub.

NOTE: The retainer ring is tapered and must be installed flat side down.

4. Remove and Discard the retainer ring.

5. Using a suitable press, remove the bearing from the wheel knuckle and discard the bearing.

CAUTION: The hub and bearing cannot be reused after disassembly.
To install, reverse the removal procedure.

Jan 24, 2010 | 2002 Ford Explorer

2 Answers

Replace rear wheel bearing 2002 ford explorer 4x4


you must remove brakes, then remove axle nut, then remove upper control arm and finally tie rod stabilizer, remove axle from car then bearing can be accessed. this is a difficult job that requires special tools so be careful

Aug 15, 2009 | 2002 Ford Explorer

1 Answer

How do I replace the hub assy on a 2004 ford explorer AWD?


Hi,
I was referring to the Haynes Repair Manual #36025, Ford Explorer 2002-2006, Chapter 10, "Hub and bearing assembly (rear) replacement": Due to the special tools and expertise required to press the hub and bearing from the rear knuckle, this job should be left to a professional mechanic. However, the knuckle may be removed and taken to an automotive machine shop or other qualified repair facility equipped with the necessary tools.

Thank You for contacting Fixya.com

Aug 03, 2009 | 2004 Ford Explorer

1 Answer

2002 ford explorer front wheel bearing assembly


remove hub ,take retaining circlip out and knock it out with a big big hammer supporting it on an old wheel rim and a tree trunk.this job is easy to do but unless you have the right tools entrust it to a garage who will have a nice press .

Feb 02, 2009 | 2002 Ford Explorer

1 Answer

Rear Hub and bearing replacement cost


you are looking at $197.88 to $229.09 for the hub assembly (this is for both the bearings and the hubs) and this is just a guess but anywhere from $95.00 to $125.00 for the labor cost
but you can do what I did find a place where the salvage yard is self service and take the hub and bearing assembly off the car in the yard and put on yours cause I only paid $18.00 for the hub and bearings taking them off and putting back on myself you can do it just take your time and have someone to help you and do one wheel at a time

Jan 05, 2009 | 2002 Ford Explorer

1 Answer

Rear Axle Bearing


i know for a fact that the bearing comes with the hub., and if the old bearing is badly damage you may need to heat it to remove it from the axel...so this may be a rather big job if your not equipt
with torch or other ...

May 29, 2008 | 2002 Ford Explorer

Not finding what you are looking for?
2002 Ford Explorer Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...