Question about 2002 Nissan Quest

1 Answer

How do I replace the headlight assembly on a 2002 nissan quest?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert whose answer got voted for 20 times.

  • Expert
  • 146 Answers

There should be a three wire connector at the headlight. Disconnect it. Turn the large plastic nut that holds the bulb in place and replace the bulb.

Posted on Jul 22, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the cam sensor in a 2002 nissan quest?

HI Chuck! The cam position sensor is inside the distributor on the quest. If the cam sensor has gone bad you need to replace the distributor assembly as it is not servicable. Before replacing the distributor, take the cap off and make sure the rotor is turning when you crank the engine. If it is not then check the timing belt as the distributor is driven by the cam shaft. If the belt is broken the cam shaft will not turn and you could get this code.The cam sensor is located under the plastic cover located under the rotor button

Nov 18, 2016 | Nissan Cars & Trucks

1 Answer

How do I replace the head light module on a 2001 Nissan Quest

Yes it will as it sounds like the headlight relay is faulty and randomly switching the lights around

Oct 14, 2014 | 2001 Nissan Quest

1 Answer

How do you remove the front headlight assembly on a 2009 Nissan Quest?

are you trying to replace bulb if so open hood and behind the assembly is the bulb tight fit but un screw a ring and pull old bulb out and put replacement bulb in. if replacing whole assembly there is a couple clips on it may need to remove bumper cover to see bottom clip

Apr 06, 2013 | Cars & Trucks

1 Answer

How do you replace low beam headlight on a 2006 nissan quest? passager side

if you mean the headlight bulb then iam afraid its a bumper off job ,no quick way on modern cars as no access

Mar 29, 2011 | 2006 Nissan Quest

1 Answer

I have a 2008 nissan quest with a front passenger low beam headlight out. I want to change it myself but do not know how to take off headlight housing

Open the hood and look at the back of the headlamp assembly. You should see a wiring connection which you will disconnect, then turn the bulb socket until you can pull it back out of the headlamp. Replace the bulb being careful not to touch the glass with your hands (oil on fingertips shortens bulb life and may cause bulb failure). Reconnect wiring harness and repeat with the other side.

Feb 21, 2011 | Nissan Quest Cars & Trucks

1 Answer

Nissan Premira 2002, european spec. When replacing brakes pads w/ABS, are there any adjustments required or resetting procedures? My email is address

The vehicle being worked on was jacked up and supported by sturdy jack - stands. All four wheels were removed to access disc brake assemblies. Tools utilized (1) C clamp for the front caliber to press piston back in it bore and (2) a special tool for the rear to return caliber back in it bore. Replaced pads and all pertinent hardware, torque all fasteners to specification and wheel assemblies. Road tested vehicle and checked for noise and rattles. So thanks for the tip that was given and I wish you and your staff a nice sunday.


Jul 18, 2009 | 2002 Nissan Quest

1 Answer

Passenger side head light

glad you asked , its like a saftey pin , you push in on the lower side of that paper clip looking device , as you push in , move it side ways to the left or the right , depending on how your looking at it , its real dumb , just like a saftey pin . by the way there is a recall on the 2002 , 2003 altima headlights , if you see burnt connectors , or crumbly plastic were the actual bulb inserts into the light assembly , take it to nissan , under the headlight campaign , more often they will replace both headlight assemblies , all nice and new and clear . 2 thumbs up !

Jan 13, 2009 | 2002 Nissan Altima

Not finding what you are looking for?
2002 Nissan Quest Logo

Related Topics:

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides