Question about 1990 Jeep Wrangler

2 Answers

Will not go into any gear,without turning off engine 1990 yj 5 speed 4cyl

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

FromTwitter by - @carpartslocator


@car_problems your pilet bearing is bad or throw out bearing is bad or pressor plate is bad.Or your tnasmission need to be rebuild.

Good luck.

Posted on Jul 20, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 295 Answers

More than likely a bad clutch.

Posted on Jul 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Speedo 95 yj conversion 350 with 350 turbo trans and np231 transfer case 3.73 gears 33" tires wires cut off at transfer case and there is no speedo cable what do i need to get my speedo working


The vehicle speed sensor is located in the transfer case housing. To get your speedometer working you will have to connect the wires back to the speed sensor.

Nov 02, 2011 | 1990 Jeep Wrangler

1 Answer

1990 Wrangler: I have a 1990 yj with the 4.2, my question for eve...


Most 90 wranglers from 89 to 95 have an ax15 5 speed transmission in them. The 4 cylinders had an ax5 transmission.

May 17, 2010 | 1990 Jeep Wrangler

1 Answer

95 wrangler yj. has no power at high speeds


Have you had fuel pressure tested, and/or filter changed. Have you checked for plugged exhaust, such as catalytic converter? Quite often engine will also run a little hotter than normal when exhaust is plugged.

Nov 05, 2009 | 1995 Jeep Wrangler

1 Answer

1990 jeep yj 4 wheel drive issues


what are you trying to say is that the front wheels wont engage?? if this is your problem? check the actuater on the passenger side axle there are 3 lines that go to it and that is what pulls it in and pushes it out of gear by air.

Oct 06, 2009 | 1990 Jeep Wrangler

1 Answer

Transmission not going into gear


I see this is kind of a stale post, but i'll try anyway. First, check your clutch fluid reservoir. If it's full, you may have air in the line, a bad master cylinder, or slave cylinder, or your clutch is worn out.

May 11, 2009 | 1990 Toyota 4Runner

1 Answer

No injector pulse, no current to the injector


Check the pickup in the distributor as this is the cam sensor. The injectors run of the pulses created while the rotor is turning around. It should be a plastic disk located under the rotor button.

Mar 13, 2009 | 1990 Jeep Wrangler

1 Answer

1992 YJ can only shift into 3rd & 4th gear. No Reverse


The same thing happend to one of my wranglers, a 95 yj 4cyl 2.5 liter. The "Aisin AX-5" is the transmission that jeep used on the yj and tj 4cyl and 83 cherokee and up 4cyl, and the "Aisin AX-15"was used on some of the 6cyl models. Both are a "light duty" transmission according to the transmission manufacturer. As everyone knows, A jeep is no light duty vehicle, the shifting slider, a fork like item slides the gears back and forth over the drive and output gears to change the gears. and with heavy use or lack of maintanice they can break, they also can break cause of the cheap casting they used in the tranny. Other problems happen in those trannys too. The only thing is to tear the tranny apart and find out what failed and replace. I did this on the kitchen table ofer a day off. being the up own an early 90s yj, If you are one who doesn't work on their own car, I would find a good garage that is good with jeeps, they are not to expencive to fix, and when they are taken care of, will be a joy to own.
I hope this helps, Jeep ownership is a great thing.

Feb 11, 2009 | 1992 Jeep Wrangler

1 Answer

1990 yj manual trans will not go in any gear


possibly hydraulic clutch fluid? i have a 2002, not sure if the 93 has hydraulic clutch fluid but you might just want to check it to be safe good luck

Sep 06, 2008 | 1993 Jeep Wrangler

Not finding what you are looking for?
1990 Jeep Wrangler Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...