Question about Jeep Cars & Trucks

1 Answer

Where is crankshaft position sensor located on 2005 Jeep Grand Cherokee Laredo 4.7

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 83,940 Answers

It Is located behind the engine starter motor.

Posted on Oct 31, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE TO CHANGE OUT A CRANK SENSOR IN MY GRAND CHEROKEE.


Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .


Oct 24, 2015 | Cars & Trucks

1 Answer

Where is the crankshaft position sensor on a 2003 jeep grand cherokee laredo located V6 4.0


The Crankshaft Position Sensor (CKP) is mounted to the transmission bellhousing at the left/rear side of the engine block...

9_21_2011_12_48_19_pm.jpg


9_21_2011_12_48_47_pm.gif

Inatallation: 4.0L Engine
New replacement sensors will be equipped with a paper spacer glued to bottom of sensor. If installing (returning) a used sensor to vehicle, a new paper spacer must be installed to bottom of sensor. This spacer will be ground off the first time engine is started. If spacer is not used, sensor will be broken the first time engine is started.

New Sensors:
Be sure paper spacer is installed to bottom of sensor. If not, obtain spacer PN05252229.

Used Sensors:
Clean bottom of sensor and install spacer PN05252229.
  1. Install sensor into transmission bellhousing hole.
  2. Position sensor wire shield to sensor.
  3. Push sensor against flywheel/drive plate. With sensor pushed against flywheel/drive plate, tighten mounting bolt to 7 Nm (60 inch lbs.) torque.
  4. Route sensor wiring harness into wire shield.
  5. Connect sensor pigtail harness electrical connector to main wiring harness.
Hope helps (remember to rate and comment this free answer).

Sep 06, 2011 | 2003 Jeep Grand Cherokee

1 Answer

No power to the coil on a 1994 jeep cherokee laredo.


Bad ignition module, crankshaft position sensor, or bad knock sensor. All three can cause that.

Mar 08, 2011 | 1994 Jeep Grand Cherokee

1 Answer

Where is crank shaft position sensor located on 1997 jeep grand cherokee


CRANKSHAFT POSITION SENSOR LOCATION FOR 4.0L ENGINE IS ON TRANSMISSION BELLHOUSING AT THE LEFT REAR OF THE ENGINE. FOR 5.2L ENGINE CRANKSHAFT SENSOR LOCATED ENGINE BLOCK BEHIND THE RIGHT CYLINDER HEAD.

Dec 11, 2010 | 1997 Jeep Grand Cherokee

2 Answers

Where is locate the camshaft position sensor on 2001 jeep grand cherokee laredo limited 4.7 l


The camshaft position sensor is located inside the distributor. It is a hall effect swich, simply remove the distributor cap and the rotor and you can lift it out, unplug and replace.
Have fun but beware a bad crankshaft position sensor can cause a false cam sensor code to be set sometimes.
Good luck.

Dec 05, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Crankshft position sensor


Hi I can help but need to know what engine you have.

Oct 22, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Wont start 1996 jeep grand cherokee laredo inline six4.0 fuel inj


The first thing I would do since you think it was flooded is to replace the sparkplugs, sometimes if a spark plug has been washed out with gas you cannot get it completely dried out. After you replace sparkplugs try to start the engine. If the engine starts I would still recommend that you change your oil because of fuel saturation. If your engine fails to start I would suspect that you have a bad crankshaft position sensor as it is known to give problems. The crankshaft position sensor is located on the top of the transmission bell housing on the drivers side.

Oct 02, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Location of crankshaft position sensor Jeep grand cherokee 1997


left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Jun 13, 2009 | 1995 Jeep Grand Cherokee

1 Answer

2001 jeep cherokee grand laredo starting problem


Try replacing the crankshaft sensor sounds like thats your problem if not the fuses or relays still no luck them you might have pcm problems....

Jul 15, 2008 | 2001 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

83940 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...