Question about 1995 Lexus ES 300

1 Answer

93 es 300 runs high on first gear

The vehicle would run high on the first gear, wont go past 20 mph, unless I stop accelaritng for a second, it'll drive normal when I accelarate again.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

First gear is gone,you need to rebuild your transmiching

Posted on Jul 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes I/P lights to blink when put in gear?


2005 Chrysler 300 2.7l Throttle Body Control Warning Light ...

www.cargurus.com > Questions > Chrysler > 300

CarGurusAug 7, 2014 - 2005 Chrysler 300 2.7L throttle body Control warning light or "RED ...bolt starts flashing and the car gets stuck in limp mode or second gear.Missing: p

PCM/TCM Software Updates Will Address Shifting Problems ...

repairpal.com > Problems > Chrysler > 300
Chrysler 300 PCM/TCM Software Updates Will Address Shifting Problems. ... If you experience rough shift and/or shuddering during gear shifting, software ... Car would not go over 20 mph and check engine light along with ABS/BAP light ... Once he put the new battery in the car ran fine for a while and the problems all cam ...Missing: p

ECM with bad connection, causing engine to stall - 2005 ...

? 1:08
https://www.youtube.com/watch?v=IgLe0t5may8
Oct 23, 2011 - Uploaded by SignedOnAsJoe
Check NHTSA chrysler extended the warranty on fuel tanks. ...Any one knows how can I put a used ecm in my 2005 300 do I need to buy new ... How to view fault codes Chyrsler 300 HTWL - Duration: 1:22. by Leo P 28,908 views ... Rough Run, Stumble or Stall, Check Engine Light-How To Check Vehicle ...Missing: blink

Dec 19, 2015 | 2005 Chrysler 300 Touring

1 Answer

I will be honest here...I am a woman who knows NOTHING about cars. Also I am a single mom, who cant afford yet another mechanic...so here goes. I have a 1996 Lexus ES 300...this doesnt happen all of the...


It may be your transmission. If it shifts hard going through gears also then it may be that. But what you decribed it it slipping gears which would target your transmission or rear end.

Dec 08, 2012 | 1996 Lexus ES 300

1 Answer

I have problem on lexus es 300 99 year, when i driving at 70 miles my rpm is going to 4000. My overdrive it does not work. I have check engine light and its code is knock sensor bank 2.


My Lexus es 300 most often when engine is warm will not shift in to last gear. Stop engine start it will shift ok when engine is cool. engine pings kock senores. When in gear at high speed the car runs like new?? Car run bad in hot weather. VSC light on. Red light looks a circle with red line through it comes on not always..

Sep 03, 2010 | 1999 Lexus ES 300

2 Answers

Not Ready for Smog test


it is not how many miles but the type of driving.

here is a OBD2 drive cycle test.

Generic OBD II "Drive Cycle" Most OBD II ("On-Board Diagnostics II") diagnostic monitors will run at some time during normal operation of the vehicle.
However, to satisy all of the different Trip enable criteria and run all of the OBD II diagnostic monitors, the vehicle must be driven under a variety of conditions. The following drive cycle will (theoretically) allow all monitors to run on (??) vehicle. (Note: Drive cycle specifics vary by vehicle!)
  1. Ensure that the fuel tank is between 1/4 and 3/4 full.
  2. Start cold (below 86°F /30°C) and warm up until engine coolant temperature is at least 160° F (typically requires at least one minute; up to 3 minutes).
  3. Accelerate to 40-55 MPH at 25% throttle and maintain speed for five minutes.
  4. Decelerate without using the brake (coast down) to 20 MPH or less, then stop the vehicle. Allow the engine to idle for 10 seconds, turn the key off, and wait one minute.
  5. Restart and accelerate to 40-55 MPH at 25% throttle and maintain speed for two minutes.
  6. Decelerate with using the brake [or the clutch!] by coasting down to 20 MPH or less, then stop the vehicle. Allow the engine to idle for 10 seconds, turn the key off, and wait one minute.

Jun 04, 2010 | 2001 Kia Sephia

1 Answer

My 93 lexus es 300 transmission will not shift


if it has cables for your shifter xheck them they break.im assuming its an standard

Oct 12, 2009 | 1993 Lexus Es 300

2 Answers

How do i reprogram the computer on my 2002 xl7


Try this relearn procedure hopefully it will help

Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Many vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. The computer will use default data until new data from each key start is stored. As the computer memorizes vehicle operation for each new key start, driveability is restored. Vehicle computers may memorize vehicles operation patterns for 40 or more key starts. Customers often complain of driveability problems during the relearn stage because the vehicle acts differently then before being serviced. Depending on the type of vehicle and how it is equipped, the following complaints (driveability problems) may exist:

Harsh Or Poor Shift Quality
Rough Or Unstable Idle
Hesitation Or Stumble
Rich Or Lean Running
Poor Fuel Mileage

These symptoms and complaints should disappear after a number of drive cycles have been memorized. To reduce the possibility of complaints, after any service which requires battery power to be disconnected, vehicle should be road tested.

Vehicle Preparation

Ensure all components are connected. Ensure transmission fluid level is correct. Warm engine to normal operating temperature. If vehicle has been repaired, perform KOEO and Continuous Memory Code Self-Test and ensure fault codes are not present.

Computer Relearn Procedures

Idle Relearn Procedure

Place automatic transmission in Park or manual transmission in Neutral position. Ensure the emergency brake has been set and all accessories are turned off. Start engine and bring to normal operating temperature. Allow manual transmission vehicle to idle in Neutral for one minute. Allow automatic transmission to idle in Neutral for one minute and then to idle in Drive for one minute. Once initial relearn is complete, process will be completed during normal driving. Always complete the procedure before returning the vehicle to the customer.

Drive Cycle Test (AOD-E, AXOD & AXOD-E TRANSAXLES)

With transmission gear selector in Overdrive, moderately accelerate vehicle to 50 MPH for a minimum of 15 seconds. Transmission should be in 4th gear. While holding speed steady, lightly apply and release brake for about 5 seconds. Stop and park vehicle for a minimum of 20 seconds with transmission gear selector in Drive. Repeat procedure 5 times. Always complete the procedure before returning the vehicle to the customer.

Drive Cycle Test (E4OD)

With transmission gear selector in Drive, press Overdrive Cancel Switch (LED should light). Moderately accelerate vehicle to 40 MPH for a minimum of 15 seconds (30 seconds above 4000-ft. elevation) Transmission should be in 3rd gear. While holding speed steady, press Overdrive Cancel Switch (LED should go off) and accelerate from 40 MPH to 50 MPH. Transmission should shift from 3rd gear to 4th gear. Hold speed steady for 15 seconds. While holding speed steady, lightly apply and release brakes enough to turn brake lights on. Maintain 50 MPH for about 5 seconds. Stop vehicle for a minimum of 20 seconds with transmission gear selector in Drive. Repeat procedure 5 times. Always complete the procedure before returning the vehicle to the customer.

Mar 26, 2009 | 1998 Lincoln Mark VIII

1 Answer

My 93 ford probe gt wont idle and wont shift outa 2nd gear


Sounds like you need to check your vaccum lines for a leak. This is easy to do. Buy a can on carburator cleaner and with a friends help keep the car running as you spray your vaccum lines with the carburator cleaner one by one. If you have a leak it will **** the cleaner into the lines and cause the vehicle to stall out. Replace the line if this happens and continue checking all lines until all bad lines are replaced.

Mar 15, 2009 | 1993 Ford Probe

Not finding what you are looking for?
1995 Lexus ES 300 Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

907 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...