Question about 1993 Lexus Es 300

1 Answer

My 93 es 300, runs high on first gear, won't go past 20 mph unless i let go of the accelerator for a second then accelerate again it'll drive normal.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

You might want to look into a new clutch or your release bearing for you clutch is wearing out

Posted on Jul 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not accelerate past 20 mph/slows/shuts off


Better check your codes again sounds like your converter is plugged up

Feb 04, 2014 | 2003 Hyundai Santa Fe

1 Answer

My 1997 Jimmy runs fine in idle when I take off the vechile is fine until it reaches 20 mph it won't accelerate and the rpms increase up to 3000 but no speed. What's wrong it's a 4 wheel d


Sounds like 2nd gear in the transmission is slipping. Cars usually shift at 15-20 mph from first to 2nd. First check the trans fluid.

Mar 17, 2013 | 1997 GMC Jimmy

1 Answer

2005 chrysler 300c. The pedal is to the floor


if it is an automatic ( speed sensor mentioned ) check the gear linkage selector /cable for proper adjustment as it may not be selecting correctly into drive

Mar 21, 2017 | 2005 Chrysler 300

1 Answer

93 es 300 runs high on first gear


First gear is gone,you need to rebuild your transmiching

Jul 19, 2009 | 1995 Lexus ES 300

1 Answer

1995 Explorer conversion van won't accelerate


Sounds like you have a transmission problem, could be the valve body, or a bad band. I would check the fluid first it could be low. Just make sure the engine is warm, and the van is in park, then check the fluid.

Jun 20, 2009 | GMC Vandura Cars & Trucks

1 Answer

1997 Suburban 4x4 5.7L Transmission whines until it shifts


You rear planetary set is worn from a restricted cooler.

May 06, 2009 | 1997 Chevrolet Suburban

2 Answers

How do i reprogram the computer on my 2002 xl7


Try this relearn procedure hopefully it will help

Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Many vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. The computer will use default data until new data from each key start is stored. As the computer memorizes vehicle operation for each new key start, driveability is restored. Vehicle computers may memorize vehicles operation patterns for 40 or more key starts. Customers often complain of driveability problems during the relearn stage because the vehicle acts differently then before being serviced. Depending on the type of vehicle and how it is equipped, the following complaints (driveability problems) may exist:

Harsh Or Poor Shift Quality
Rough Or Unstable Idle
Hesitation Or Stumble
Rich Or Lean Running
Poor Fuel Mileage

These symptoms and complaints should disappear after a number of drive cycles have been memorized. To reduce the possibility of complaints, after any service which requires battery power to be disconnected, vehicle should be road tested.

Vehicle Preparation

Ensure all components are connected. Ensure transmission fluid level is correct. Warm engine to normal operating temperature. If vehicle has been repaired, perform KOEO and Continuous Memory Code Self-Test and ensure fault codes are not present.

Computer Relearn Procedures

Idle Relearn Procedure

Place automatic transmission in Park or manual transmission in Neutral position. Ensure the emergency brake has been set and all accessories are turned off. Start engine and bring to normal operating temperature. Allow manual transmission vehicle to idle in Neutral for one minute. Allow automatic transmission to idle in Neutral for one minute and then to idle in Drive for one minute. Once initial relearn is complete, process will be completed during normal driving. Always complete the procedure before returning the vehicle to the customer.

Drive Cycle Test (AOD-E, AXOD & AXOD-E TRANSAXLES)

With transmission gear selector in Overdrive, moderately accelerate vehicle to 50 MPH for a minimum of 15 seconds. Transmission should be in 4th gear. While holding speed steady, lightly apply and release brake for about 5 seconds. Stop and park vehicle for a minimum of 20 seconds with transmission gear selector in Drive. Repeat procedure 5 times. Always complete the procedure before returning the vehicle to the customer.

Drive Cycle Test (E4OD)

With transmission gear selector in Drive, press Overdrive Cancel Switch (LED should light). Moderately accelerate vehicle to 40 MPH for a minimum of 15 seconds (30 seconds above 4000-ft. elevation) Transmission should be in 3rd gear. While holding speed steady, press Overdrive Cancel Switch (LED should go off) and accelerate from 40 MPH to 50 MPH. Transmission should shift from 3rd gear to 4th gear. Hold speed steady for 15 seconds. While holding speed steady, lightly apply and release brakes enough to turn brake lights on. Maintain 50 MPH for about 5 seconds. Stop vehicle for a minimum of 20 seconds with transmission gear selector in Drive. Repeat procedure 5 times. Always complete the procedure before returning the vehicle to the customer.

Mar 26, 2009 | 1998 Lincoln Mark VIII

1 Answer

My 93 Lexus ES 300 has miss while idling.


the ignition coil is very easy to replace it would be located on the side of the car chasis next to the engine and would have one cable coming from it with a couple of wires leading to it that would affect the acceleration to a certain degree

Mar 10, 2009 | 1995 Lexus ES 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...