Question about 2002 Suzuki XL-7

2 Answers

Suzuki xl7 oxeygen sensor bank 1 sensor 2

I have the same problem - failed emmissions test - were you able to replace them yourself? I got a good deal at standard auto parts 330 for two. apparently there are 4 sensors - 2 before the c-converter and 2 after. i think bank 1 is before. suzukie wanted almost 300 for 1

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,615 Answers

You may not need a special socket. You will need a 7/8 box wrench. Inspect what your looking at first. Sometime it does take a special angled wrench but usually not.

Posted on Jul 19, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 135 Answers

You will need a special socket to remove the 02 sensors and a good solvent to spray on the threads to help break them loose. The socket can be purchased at most auto parts stores.

Posted on Jul 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

07 suzuki xl7 po420 code. Oxygen sensor bank 2 sensor 1 i believe. Location in the engine. Thanks..


the cold from hell,,
CAT monitor. know it well, too well.

no its not that.
the code tells that engine has a lazy or dead cat.
no engine stated.
its and XL-7 not and XL7, they are different cars.
3.6L V6
bank one is failing the person who told you bank 2 is full of beans.

"Catalyst Efficiency Below Normal (Bank 1)" SM quote. we change the front B1S1 front sensor first.
then the B1S2, sensor next.
then the CAT if sure no exhaust leaks are on Bank1.
S1 is front
S2 is rear
bank 1, is cylinder 1 side
bank 1 is,, right bank, usa is passenger side

look for leaks first in exhuast
then bad 02s, on right side , damage to wires.
the new sensors.
then new cat, $$$$$$$$$$$$$$$$$$$ last

Mar 12, 2017 | 2007 Suzuki XL-7

1 Answer

P0017 on a 2007 suzuki xl7


did you look it up?
alldata.com shows.
it means the engine needs service and inspections here.

Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor "B"
Number of Trips to Set Code: 2
Trouble Code Conditions:
Difference between camshaft (bank 1 / exhaust side) position and crankshaft position is out of specified range.
Possible Causes:
  • CMP sensor
  • CKP sensor
  • Signal rotor
  • Timing chain
  • Timing chain tensioner
  • CMP actuator
  • ECM

Feb 24, 2014 | 2007 Suzuki XL-7

1 Answer

2002 suzuki xl7 is throwing engine codes poo31 and p0446. The car is jerking really bad, often smells like fuel on the inside of the car, and sometimeswhen you try to put gas in it the gas spits back out...


PO-446 EVAP Vent Valve ( Cause of fueling issues & smell)

PO-31 O2 Sensor Bank 1 Sensor 1 ( Bad Heater)

Replace both front O2 Sensors

EGR Valve and or spark plugs (for Jerky)

Feb 20, 2011 | 2002 Suzuki XL-7

2 Answers

My 1998 chevy suburban K1500 with 160k miles failed emmissions test because of a P0135 code (O2sensor in bank 1, sensor 1 malfunction) and the MIL on. All emmissions levels were within spec, and only...


check the connector on some chevys they go bad i have replaced them before so try a new connector or maybe that the wire got burned with the exaust pipe or even disconnected ?? good luck.

Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Suzuki xl7 which side is bank 2 sensor 2


I assume then that this is a v6. Bank one should be the drivers side (I think) . Sensor 1 would be the one before the catalytc convertor and sensor 2 would be the one after it.

Mar 11, 2010 | 2002 Suzuki XL-7

1 Answer

2003 suzuki xl7


It is not unusual for a camshaft sensor (or crankshaft position sensor) to fail. They are replaceable. If the onboard computer does not get the correct input it cannot control the engine timing correctly and automatically shuts down.

Jul 14, 2009 | Oldsmobile Alero Cars & Trucks

2 Answers

How do I reset the engine light after a P0496 code?


Unplug the battery for 15 minutes and then plug the battery back in, but until you fix the oxeygen sensor you are going to continue to have the code thrown

Apr 29, 2009 | 2001 Suzuki Xl 7

1 Answer

Ihave a 2002 suzuki xl7 and i have a error code low voltage bank 2 sensor 1. is this the oxygen sensor on the passenger side before the cat?


Yes, If you have dual exhaust pipes coming from the engine, Look on the passenger side exhause pipe, and it will be the 1st sensor on the pipe coming out of the engine.

Apr 26, 2009 | Suzuki XL7 Cars & Trucks

Not finding what you are looking for?
2002 Suzuki XL-7 Logo

Related Topics:

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...