Question about 2000 Audi A6

1 Answer

Removal of head lamp pod to install new one. - 2000 Audi A6

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,071 Answers

Front bumper cover needs to be removed then there are bolts on radiator support and behind assembly

Posted on Jul 23, 2009

  • paul campbell Jul 23, 2009

    front bumper cover needs to be removed then there are bolts on radiator support and behind assembly

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change instrument lights bulb for vw polo 1997 1.4


You will need to remove the clocks, here's how
1. remove the plastic surround held by two screws might be torx screws.
2. you will see 4 screws either side of the instrument pod, remove them
3. hold the top od the pod and pull towards you
4. unplug the multiplug connector on the back
5. wiggle the pod out through the middle of the steEring wheel (you might find it helps to slack off the adj steering lever)
6. you will now see the twist fit bulbs, replace them with t501 type lamps
7. then refitting is the reversal of above! or something along those lines.

Mar 18, 2017 | Volkswagen Polo Cars & Trucks

Tip

How to Replace the planetary gear in an Odometer of car?


The procedure is follows:--
1) First of all disconnect the negative cable from the battery of car.
2) With flat head screwdriver, pry the gasket around the edge of the face of speedometer gauge away from the dash and remove the gasket.
3) You will have to pull the entire speedometer gauge out of the dash;
NOTE:-- do not to disconnect the connecting electrical wires when you pull speedometer.
4) Then remove the speedometer needle by turning the needle clockwise.
5) Then remove the two screws in the face of the gauge with screwdrivers.
6) Remove the motor casing for the odometer out from the dial after the screws are removed.you will need to pull the motor casing a bit to remove it out.
7) In the motor casing you will see the gear pod at the top of the motor casing. Slightly with bit force remove the gear pod. The gear pod is attached to the "lid" of the casing .
8) You will see the odometer planetary gear in the gear pod which you removed.Remove the planetary gear from the gear pod with the help of mini flat head screwdriver.
9) Insert new gear into position and reassemble the gauge by reversing the procedure.
this will help.Thanks.

on Mar 15, 2010 | Audi A4 Cars & Trucks

Tip

How to Repair an Odometer in car?


The procedure is follows:--
1) First of all disconnect the negative cable from the battery of car.
2) With flat head screwdriver, pry the gasket around the edge of the face of speedometer gauge away from the dash and remove the gasket.
3) You will have to pull the entire speedometer gauge out of the dash;
NOTE:-- do not to disconnect the connecting electrical wires when you pull speedometer.With the gauge face down remove the screws from the back of the case with a screwdriver. After removing the screws , lift the gauge out of its casing and see its back.
4) Then grasp the post to reset the trip odometer. Do it very carefully;
5) Then remove the speedometer needle by turning the needle clockwise.
6) Then remove the two screws in the face of the gauge with screwdrivers.
7) Remove the motor casing for the odometer out from the dial after the screws are removed.you will need to pull the motor casing a bit to remove it out.
8) In the motor casing you will see the gear pod at the top of the motor casing. Slightly with bit force remove the gear pod. The gear pod is attached to the "lid" of the casing .
9) You will see the odometer planetary gear in the gear pod which you removed.Remove the planetary gear from the gear pod with the help of mini flat head screwdriver.
10) Insert new gear into position and reassemble the gauge by reversing the procedure.

This will help.thanks.

on Mar 15, 2010 | Buick Century Cars & Trucks

1 Answer

Relace Headlight Bulb


Hope this helps and please don't forget to rate! Thanks!


Removal & Installation
  1. Disconnect battery cable.
  2. Remove the head lamp bolts.
  3. Disconnect the head lamp connector.
  4. Remove the head lamp.
  5. Installation is the reverse order of removal procedure.


c17hydro_146.gif

Headlight bulbs-2000-2005 Accent

Jan 23, 2011 | 2001 Hyundai Accent

1 Answer

How do I replace the front left (driver side) headlight? I have removed the cap and the electrical, but can't figure out how to remove the bulb so I can put a new one in. Your help is appreciated.


Removal & Installation
  1. Disconnect the negative battery terminal.

  2. Remove the head lamp mounting bolts, then disconnect the lamp connectors.

  3. Replace the head lamp bulb(A), position bulb(B) and turn signal bulbs(C).
    41311_tucs_g0048.gif

    Head lamp bulb(A), position bulb(B) and turn signal bulbs(C)

  4. To install, reverse removal procedure.

Dec 12, 2010 | 2005 Hyundai Tucson

2 Answers

Head lamps will not go on. Does the head lamps


No fuse or relay. A new head light switch is needed instead

Apr 25, 2010 | 1987 Ford Ranger

2 Answers

How to replace headlights bulbs in a grand cherokee 2001


  1. Remove the jack screw attaching the top of the head lamp to the head lamp mounting module.
  2. Grasp the upper inboard and lower outboard corners of the head lamp and pull the head lamp outward.
  3. Remove the bad bulb socket from the head lamp module and remove bulb from socket.
  4. Install new bulb into socket and reinstall socket into head lamp module.
  5. Position the head lamp on the vehicle and align the ball studs with the sockets.
  6. Push the head lamp inward to secure the ball studs with the sockets.
  7. Install the jack screw attaching the top of head lamp to the head lamp mounting module.
Do not touch glass of halogen bulbs at the oil can cause the headlight to blow out

Nov 12, 2009 | 2001 Jeep Grand Cherokee

1 Answer

I need instructions on how to remove/install headlight assembly on a 1990 civic ex 4 door


open the bonnet, unlock the latch for head lamp cover the and remove the head lamp cover and replace the head lamp.

Sep 18, 2009 | 1990 Honda Civic

1 Answer

How do i replace a sidelight on a grand cherokee '53


The whole head lamp assembly has to come out to replace the headlight bulb. Here's how to do it.
REMOVAL:
  1. Remove the jack screw attaching the top of the head lamp to the head lamp mounting module.
2. Grasp the upper inboard and lower outboard corners of the head lamp and pull the head lamp outward.

  1. Remove all of the bulb sockets from the head lamp module.
  2. Separate the head lamp from the vehicle
  3. INSTALLATION: CAUTION: Do not touch the bulb glass with fingers or other oily surfaces. Reduced bulb life will result.
  4. Install all of the bulb sockets in head lamp module.
  5. Position the head lamp on the vehicle and align the ball studs with the sockets.
  6. Push the head lamp inward to secure the ball studs with the sockets.
  7. Install the jack screw attaching the top of head lamp to the head lamp mounting module

Aug 17, 2009 | 2003 Jeep Grand Cherokee

1 Answer

Installing new head lamps in a 2003 Pontiac Grand Am


It varies a bit from car to car, but generally you can pop the hood and see right where the wires go into the back of the headlight lens. Most have a tab that you press, then rotate the assembly to remove. Then, you can just plug the new bulb in and reverse the process. Most work that way.

Jul 25, 2009 | 2003 Pontiac Grand Am

Not finding what you are looking for?
2000 Audi A6 Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...