Question about 2005 Chrysler 300

1 Answer

2005 chryler 300 eng hood will not open -cable is

2005 chrysler 300 eng hood will not open -cable is broke - How do I open to repair?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 118 Answers

You can access the hood release from the front of the car under and behind the front bumper.

Posted on Jul 19, 2009

  • Don Cahala Dec 26, 2011

    Not on this model. The front splash pan and engine cradle prevent getting into the latch easily. If one were to partially remove the splash pan , which is part of the front bumper and wriggle a hand in there, one might be able to click it open. Once open, remove the two blots holding the latch down and re-route a new cable. (fun)

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My serpentine belt broke on my chrysler 300 yr 2005 eng 3.5 i was told air compresser seized is there any way i can fix it without replacing compresser


You might be able to use a shorter belt and not go around compressor pulley. Use a length of string to get a rough idea of what belt you need.

Oct 12, 2016 | 2005 Chrysler 300

1 Answer

How to change alternator 2005 chryler 300


This answer covers:
2005 Chrysler 300 6cyl VIN "G" 3.5L SFI HO (72% of 2005 300's)
2005 Chrysler 300 6cyl VIN "R" 2.7L MFI DOHC (28% of 2005 300's)
2005 Dodge Magnum 5.7L engine

Alternator

Removal & Installation


WARNING - Precautions Section:
Disconnect negative cable from battery before removing battery output wire (b+ wire) from alternator. Failure to do so can result in injury or damage to electrical system.

2.7L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Disconnect alternator field circuit plug.
  5. Remove B+ terminal nut and wire.
  6. Remove 2 lower mounting bolts.
  7. Remove alternator.
To install:
  1. Install alternator.
  2. Install upper bolt mounting bolt.
  3. Install 2 lower mounting bolts.
  4. Tighten bolts to 48 ft. lbs. (65 Nm).
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Connect alternator field circuit plug.
  7. Install alternator drive belt.
  8. Connect negative battery cable.
3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Remove bracket bolts.
  5. Remove upper mounting bolt.
  6. Raise and support vehicle.
  7. Remove middle splash pan.
  8. Disconnect alternator field circuit plug.
  9. Remove B+ terminal nut and wire.
  10. Remove lower mounting bolts.
  11. Remove alternator.
To install:
  1. Install alternator.
  2. Install lower mounting bolts. Loosen install the upper mounting bolt.
  3. Tighten lower mounting bolts to 48 ft. lbs. (65 Nm).
  4. Connect alternator field circuit plug.
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Install middle splash pan.
  7. Lower vehicle.
  8. Remove loose installed upper bolt.
  9. Install bracket and bracket bolt.
  10. Install upper mounting bolt and bracket.
  11. Tighten upper mounting bolt to 48 ft. lbs. (65 Nm).
  12. Tighten the bracket bolt to 40 ft. lbs. (54 Nm).
  13. Install alternator drive belt.
  14. Connect negative battery cable.
5.7L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable at battery.
  3. Remove alternator drive belt.
  4. Raise and support vehicle.
  5. Unsnap plastic insulator cap from B+ output terminal.
  6. Remove B+ terminal mounting nut at rear of alternator. Disconnect terminal from alternator.
  7. Disconnect field wire connector at rear of alternator by pushing on connector tab.
  8. Remove alternator support bracket nut and bolt. Remove support bracket. See Figure 1.
  9. Remove 2 alternator mounting bolts. See Figure 2.
  10. Remove alternator from vehicle.

Fig. 1 Alternator Support Bracket - 5.7L engine

7309257c-afe6-4c17-9422-d7fa2e3bd4b1.jpg

Fig. 2 Alternator Mounting Bolts - 5.7L engine

22b81ff7-7912-467f-9eaf-13ba2ff3a1a4.jpg

Oct 13, 2014 | 2005 Chrysler 300

1 Answer

Won't go in gear


same problem i had before it didnt shift into gear did it get stuck when trying to put in park? well if so its your shift cable you can only get that at the dealer and it will cost you about $100.00 with out the labor of course. i have a chryler 300 ( 2005 ) also if you go on utube you can see how to do it yourself not difficult .

Sep 11, 2013 | 2005 Chrysler 300

1 Answer

Need serp belt diagram for 05 chrysler 300 3.5 looked under hood, couldn't find routing diagram anywhere


Hi, I'm JuggerBot.

Here is a diagram for you.

I hope your repair goes well.

11_2_2011_10_13_43_pm.gif

Nov 02, 2011 | 2005 Chrysler 300

2 Answers

How do I program keyless entry in a chrysler 300 touring?


i think you have to have the shops computer for them i would take it to nearest dealer it normaly cost $10.00

Nov 21, 2010 | 2005 Chrysler 300

1 Answer

Hood release cable broke on chrysler 300m how can i open the hood to repair


try going back to were the cable is inside your car get needle nose pliers or a set of locking pliers and pull on the cable if not you will have to get under the car and release the hood from the locking mechanism

Jan 26, 2010 | 2000 Chrysler 300M

1 Answer

Eng. light came on my 2005 chrysler 300. code came back to egr valve. how can i replace it myself?


it should be arond the throttle body and might have two to 4 screws in it

Nov 11, 2009 | 2005 Chrysler 300

2 Answers

How can I open the trunk if the battery is down on a 2006 crysler 300


This happened to me. You can attach jumper cables under the hood that will allow you to pop trunk. Next option, fold down rear seats and use the manual trunk release located in trunk itself.

Oct 31, 2009 | 2005 Chrysler 300

1 Answer

Chrysler 300 2001 hood won't open cable is broke


obtain a very large needlenosed plier and twist the lever as the cable would; if you can go through the grille opening with the plier.
these large 15 inch pliers are sold at Sears & Harbor Freight Tools

Apr 21, 2009 | Chrysler 300 Cars & Trucks

Not finding what you are looking for?
2005 Chrysler 300 Logo

Related Topics:

504 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...