Question about 1993 Cadillac DeVille

1 Answer

I can not get the rear brake shoe retaining spring in place. Can someone help?

Posted by on

  • yadayada
    yadayada May 11, 2010

    do u have the special tools required tro install the springs

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 520 Answers

Snap on makes brake spring tools which makes this tremendously simpler. sorry to recomend expensive tools

Posted on Jul 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instructions and diagram,to remove and replace rear drum brakes


1984 Ford Tempo - Rear Drum brake drum/shoes
REMOVAL & INSTALLATION


See Figures below instructions

1. Raise and safely support the vehicle with jackstands.

2. Remove the wheel, tire, hub and finally, the drum assembly.

3. Using a spring removal tool, remove the horizontal securing spring at the top first of the assembly.

4. Pull the adjuster locking plate away from the shoes.

5. Remove the lower horizontal securing spring.

6. Unfasten one of the 2 shoe hold-down springs and remove the pin.

7. Remove the brake adjuster.

8. Remove the remaining hold down spring and clip.

9. Lift the brake shoes assembly off the backing plate and wheel cylinder assembly. Be careful not to bend adjusting lever during the removal process.

10. Remove the parking brake cable from the parking brake lever.

11. Remove the horseshoe retaining clip and spring washer and slide the lever off the parking brake lever pin on the trailing shoe.



To install:

12. Apply a light coating of high temperature grease at the points where the brake shoes contact the backing plate.

13. Apply a light coating of lubricant to the adjuster screw threads and the socket end of the adjusting screw. Turn the adjusting screw into the adjusting pivot nut to the limit of the threads and then back-off 1 / 2 turn.

14. Assemble the parking brake lever to the trailing shoe by installing the spring washer and a new horseshoe retaining clip. Crimp the clip until it retains the lever to the shoe securely.

15. Attach the parking brake cable to the parking brake lever.

16. Attach the lower retracting spring to the leading and trailing shoe assemblies and install to backing plate. It will be necessary to stretch the retracting spring as the shoes are installed downward over the anchor plate to inside of shoe retaining plate.

17. Install the adjuster screw assembly between the leading shoe slot and the slot in the trailing shoe and parking brake lever. The adjuster socket end slot must fit into the trailing shoe and parking brake lever.



The adjuster socket blade is marked R or L for the right or left brake assemblies. The R or L adjuster blade must be installed with the letter R or L in the upright position, facing the wheel cylinder, on the correct side to ensure that the deeper of the 2 slots in the adjuster sockets fits into the parking brake lever.

18. Assemble the adjuster lever in the groove located in the parking brake lever pin and into the slot of the adjuster socket that fits into the trailing shoe web.

19. Attach the upper retracting spring to the leading shoe slot. Using a suitable spring tool, stretch the other end of the spring into the notch on the adjuster lever. If the adjuster lever does not contact the star wheel after installing the spring, it is possible that the adjuster socket is installed incorrectly.

20. Inspect your work to make sure it is correct.

21. Install the hub/drum and wheel/tire assemblies and adjust the wheel bearings.

22. Lower the vehicle and check brake operation.


archaeology_43.jpg

Fig.1 Exploded View of Rear Brakes - 1984 Ford Tempo

archaeology_44.jpg

Fig 2. Remove the brake shoe upper retaining spring with a suitable removal tool.


archaeology_45.jpg
Fig.3 Removed retaining spring - note spring direction.

archaeology_46.jpg

Fig.4 Remove the adjuster lock plate. Note the direction of the tab.

archaeology_47.jpg

Fig.5 Remove the lower retaining spring.

archaeology_48.jpg

Fig.6 Remove the Hold Down Spring - note brake spring tool used.

archaeology_49.jpg

Fig.7 remove the shoe adjuster. Note direction of the adjuster spline.

archaeology_50.jpg

Fig.8 Remove the hand brake cable.

archaeology_51.jpg

Fig.9 Remove the final brake shoe.

archaeology_52.jpg

Fig.10 All removed parts in order and properly oriented for re-assembly.

Apr 17, 2011 | 1984 Ford Tempo

1 Answer

How do you change rear drum brake shoes on a 1999 couger.


SECTION 206-02: Drum Brake 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 09/14/2001 Brake Shoes Removal
  1. Loosen the wheel nuts.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02.
  1. Remove the wheel.
  1. Release the brake shoe automatic adjuster.
    v1201041.jpg
  1. Remove the brake drum.
    1. Remove the retainers (if equipped).
    1. Remove the drum.
    v1201040.jpg
  1. Make sure that the hub flange is in the correct position as shown.
    v1201042.jpg
  1. Remove the hold down springs.
    m1201030.jpg
  1. Disconnect the parking brake cable.
    1. Lever the secondary shoe outwards.
    1. Disconnect the cable from the secondary shoe.
    v1201043.jpg
  1. Disconnect the shoes from the anchor block.
    1. Disconnect the shoes from the anchor block.
    1. Remove the lower return spring.
    v1201044.jpg
  1. ani_caut.gif CAUTION: Do not damage the wheel cylinder boots.
    Detach the shoes from the wheel cylinder.
    v1201045.jpg
  1. Hold the wheel cylinder pistons in place with a rubber band.
  1. Remove the upper return spring.
    v1201047.jpg
  1. Remove the primary shoe from the strut and brake shoe adjuster.
    1. Rotate the adjuster counterclockwise.
    1. Remove the primary shoe.
    v1201048.jpg
  1. ani_caut.gif CAUTION: Take care as the strut support spring is under tension.
    Detach the secondary shoe from the strut support.
    • Detach the strut from the shoe by levering the strut against the shoe.
    v1201049.jpg
  1. Remove the parking brake return spring.
    v1201050.jpg
Installation
NOTE: Install new shoes as axle sets.
  1. Clean, check and apply Silicon Dielectric Compound D742-18A331-A or equivalent meeting Ford specification ESA-M1C171-A to the backing plate contact points.
    v1201051.jpg
  1. Install the parking brake return spring.
    v1201050.jpg
  1. Install the secondary shoe to the strut and brake shoe adjuster.
    v1201052.jpg
  1. Install the primary shoe to the strut and brake shoe adjuster.
    1. Install the primary shoe.
    1. Rotate the adjuster fully clockwise.
    v1201053.jpg
  1. Install the upper return spring.
    v1201047.jpg
  1. Remove the rubber band holding the wheel cylinder pistons in place.
  1. ani_caut.gif CAUTION: Do not damage the wheel cylinder boots.
    Position the shoes to the wheel cylinder.
    v1201140.jpg
  1. Position the shoes to the anchor block.
    1. Install the lower return spring.
    1. Position the shoes to the anchor block.
    v1201141.jpg
  1. Install the hold down springs.
    v1201142.jpg
  1. Install the parking brake cable.
    1. Lever the secondary shoe outwards.
    1. Install the cable to the secondary shoe.
    v1201043.jpg
  1. Install the brake drum.
    1. Install the drum.
    1. Install the retainers (if equipped).
    v1201143.jpg
  1. Install the wheel.
    v1501127.jpg
  1. Operate the brake pedal to achieve automatic adjustment.

2010&c18=modelyear&c20=g167866&c35=wsm%2cbrake%20shoes%2csxu%2c206-02%2cremoval%20and%20installation&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Mar 05, 2011 | 1999 Mercury Cougar

1 Answer

Remove replace rear brakes on ford t bird 1996


1989-97 Vehicles Drum Brakes (Let me know if you need the Disc Brake Instructions)

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel and tire assemblies, then remove the brake drum.





    Fig. 4: View of the drum brake assembly with the drum removed
    88189p14.jpg





    Fig. 5: Use a commercially available brake spray to clean the
    components before removal
    88189p15.jpg


  3. Install Brake Cylinder Clamp D81L-1103-B or equivalent, over the ends of the
    rear wheel cylinder.
  4. Disconnect the parking brake cable from the parking brake lever.





    Fig. 6: Detach the parking brake cable and conduit from the
    parking brake lever
    88189g31.gif


  5. Remove the 2 brake shoe hold-down retainers, springs and pins.
  6. Spread the brake shoes over the piston shoe guide slots. Lift the brake
    shoes, springs and adjuster off the backing plate as an assembly. Be careful not
    to bend the adjusting lever.





    Fig. 7: Lift the brake shoes, springs and adjuster off the
    backing plate as an assembly
    88189p16.jpg


  7. Remove the adjuster spring. To separate the shoes, remove the retracting
    springs.
  8. Remove the parking brake lever retaining clip and spring washer. Remove the
    lever from the pin.





    Fig. 8: Drum brake components - 1995 vehicle shown
    88189g32.gif






    Fig. 9: Exploded view of the drum brake components, removed
    from the vehicle
    88189p17.jpg
    To install:

  9. Apply a light coating of caliper slide grease to the backing plate brake
    shoe contact areas.
  10. Apply a light coat of lubricant to the threaded areas of the adjuster screw
    and socket. Assemble the brake adjuster with the stainless steel washer. Turn
    the socket all the way down on the screw, then back off 1?2 turn.
  11. Install the parking brake lever to the trailing shoe with the spring washer
    and a new retaining clip. Crimp the clip to securely retain the lever.
  12. Position the trailing shoe on the backing plate and attach the parking brake
    cable. Position the leading shoe on the backing plate and attach the lower
    retracting spring to the brake shoes.
  13. Install the adjuster assembly to the slots in the brake shoes. The socket
    end must fit into the wider slot in the leading shoe. The slot in the adjuster
    nut must fit into the slots in the trailing shoe and parking brake lever.





    Fig. 10: Install the adjuster assembly in the slots in the
    brake shoes
    88189g33.gif



  14. Install the adjuster lever on the pin on the leading shoe and to the slot in
    the adjuster socket.
  15. Install the upper retracting spring in the slot on the trailing shoe and the
    slot in the adjuster lever. The adjuster lever should contact the star and
    adjuster assembly.
  16. Install the brake shoe anchor pins, springs and retainers. Remove the brake
    cylinder clamp tool
  17. Install the brake drum, wheel and tire assemblies and lower the vehicle.
  18. Apply the brakes several times while backing up the vehicle. After each
    stop, the vehicle must be moved forward.

    prev.gif next.gif

Oct 07, 2010 | 1996 Ford Thunderbird LX

1 Answer

I need a diagram of the rear brakes of a 1997 Intrepid Chrysler-where can I get one>


If the following is not enough then maybe try Alldata.com which generally has more information, but it will cost: REMOVAL & INSTALLATION Chrysler Concorde, New Yorker, LHS Dodge Intrepid Eagle Vision
  1. Remove the rear wheels and brake drums.
  2. Remove the dust cap from the rear hub and bearing assembly.
  3. Remove the cotter pin, nut retainer and wave washer. Discard the old cotter pin.
  4. Remove the rear hub and bearing assembly retainer nut and washer. Remove the rear hub and bearing assembly from the spindle.
  5. Remove the automatic adjuster spring from the adjuster lever.
  6. Rotate the automatic adjuster starwheel enough so both shoes move out far enough to be free of the wheel cylinder boots.
  7. Disconnect the parking brake cable from the actuating lever. Disconnect parking brake cable one side at a time.
  8. Remove the both lower brake shoe to anchor springs.
  9. Remove the 2 brake shoe hold-down springs from the brake shoes.
  10. Remove the brake shoes, upper shoe-to-shoe return spring, automatic adjuster and automatic adjuster lever from the backing plate as an assembly.
  11. Separate the brake shoes from the automatic adjuster mechanism.
  12. Remove the brake shoe automatic adjuster lever from the leading brake shoe. To install:
  13. Thoroughly clean and dry the backing plate. To prepare the backing plate, lubricate the bosses, anchor pin and parking brake actuating lever pivot surface lightly with lithium based grease.
  14. Remove, clean and dry all parts still on the old shoes. Lubricate the starwheel shaft threads with anti-seize lubricant.
  15. Assemble both brake shoes, the top shoe to shoe return spring, automatic adjuster and automatic adjuster lever before mounting on vehicle. Make sure the ends of the automatic adjusters are positioned above the extruded pins in the webbing of the brake shoes prior to installation.
  16. Install the brake shoe assembly onto the brake support plate and install the hold-down springs.
  17. Install the lower anchor springs and reconnect the parking brake cable to the park brake lever of the trailing brake shoe.
  18. Rotate the serrated adjuster nut to remove the free-play from the adjuster assembly.
  19. Install the automatic adjuster lever spring on the lead brake shoe assembly and the automatic adjuster lever.
  20. Install the rear hub and bearing assembly. Install washer and retainer nut and torque to 124 ft. lbs. (168 Nm).
  21. Install the wave washer, nut retainer and a new cotter pin onto the spindle. Install dust cap.
  22. Adjust brake shoes so not to interfere with brake drum installation. Install the rear brake drum. NOTE: After installing the brake drums, pump the brake pedal several times to partially adjust the brake shoes. To verify proper operation of the self-adjusting parking brake, be sure that both rear brakes are not dragging when the parking brake pedal is released.
  23. Install the rear wheels and lug nuts. Torque the lug nuts, in a star pattern sequence, to 95 ft. lbs. (129 Nm).
  24. Road test the vehicle. The automatic adjusters will continue brake adjustment during the road test of the vehicle.
prev.gif next.gif

Sep 03, 2010 | 1997 Dodge Intrepid

1 Answer

Picture or directions for repairing rear drum brake


Brake Shoes Removal & Installation Duo-Servo Type To Remove:
  1. Raise the vehicle and support it safely.
  2. Remove the tire and wheel assembly.
  3. Remove the brake drums.
  4. Using a brake tool, remove the shoe return springs.
  5. Remove the shoe guide.
  6. Remove the hold-down springs and pins.
  7. Remove the actuator lever and pivot.
  8. Remove the lever return spring.
  9. Remove the actuator link, parking brake strut, spring retaining ring.
  10. Remove the parking brake lever and washer.
  11. Remove the shoe assemblies.
  12. Remove the adjuster screw and spring from the shoe assembly.
To Install:
  1. Use brake cleaning fluid to remove dirt from the brake drum. Check the drums for scoring, cracks and for out-of-round; service the drums as necessary.
  2. Check the wheel cylinders by carefully pulling the lower edges of the wheel cylinder boots away from the cylinders. If there is excessive leakage, the inside of the cylinder will drip fluid; repair or replace as necessary.
  3. Check the flange plate, which is located around the axle, for leakage of differential lubricant.
  4. Lightly lubricate the parking brake cable, parking brake lever where it enters the shoe and the backing plate-to-shoe contact points. Use high temperature, waterproof, grease or special brake lube.
  5. Install the parking brake lever into the secondary shoe with the attaching bolt, spring washer, lockwasher, and nut. It is important that the lever move freely before the shoe is attached. Move the assembly and check for proper action.
  6. Lubricate the adjusting screw and make sure it works freely.
  7. Connect the adjuster screw and spring to the bottom portion of both shoes. Ensure the spring does not interfere with the adjuster rotation when installed. The primary (smaller shoe pad area) to the front and secondary shoe (larger shoe pad area) to the rear of the vehicle.
  8. Install the shoe assembly. Ensuring the shoe webs are positioned correctly against the wheel cylinder.
  9. Install the parking brake cable.
  10. Secure the primary shoes with the hold-down pin and spring.
  11. Install the parking brake strut and the strut spring.
  12. Install the actuator lever and pivot, securing the assembly with the hold-down pin and spring. Install the actuator link and spring.
  13. Install the return springs.
  14. Check the operation of the self-adjusting mechanism by moving the actuating lever by hand.
  15. Adjust the brakes and install the drum.
  16. Adjust the parking brake.
  17. Install the tire and wheel assembly.
  18. Lower the vehicle.
Leading-Trailing Type To Remove:
  1. Raise the vehicle and support it safely.
  2. Remove the tire and wheel assembly.
  3. Remove the brake drums.
  4. Raise the lever arm of the actuator until the upper end is clear of the slot in the adjuster screw.
  5. Slide the actuator off the adjuster pin. Disconnect the actuator spring from the shoe.
  6. Remove the hold-down spring assemblies and pins.
  7. Pull the bottom ends of the shoes apart and lift the lower return spring over the anchor plate. Allow the shoe ends to come together and remove the spring.
  8. Remove the shoe assembly, along with the upper return spring and the adjusting screw assembly.
  9. Remove the upper return spring and the adjusting screw assembly from the shoes.
  10. Remove the retaining ring, pin, spring washer, and parking brake lever.
Typical rear drum brake assembly (Leading/Trailing type) 93026g52.gif

To Install:
  1. Clean adjuster wheel and the backing plates with a suitable cleaner. Lubricate the backing plate contact points, levers and adjuster with a suitable lubricant.
  2. Assemble the parking lever, spring washer (concave side facing the brake lever), pin, and retaining ring onto the rearward shoe.
  3. Install the adjuster pin in the forward shoe with the pin projecting 0.276 in. (7mm) from the side of the shoe web where the adjuster actuator is installed.
  4. With the brake shoes resting on a flat surface (the shoe with the parking lever to the rear of the vehicle), install the upper return spring.
  5. Install the adjuster screw assembly with the spring clip facing the backing plate.
  6. Place the shoes in position on the backing plate. Do not place the lower shoe webs under the anchor plate.
  7. Install the lower return spring, spread the bottom of the shoes and position the shoe against the backing plate.
  8. Install the hold-down pins and spring assemblies.
  9. Install the adjuster actuator over the end of the adjuster pin so the top leg engages the notch in the adjuster screw.
  10. Install the actuator spring, being careful not to over-stretch it more than 3.27 in. (83mm).
  11. Install the parking brake cable to the lever.
  12. Adjust the parking brake if the shoes will not totally retract.
  13. Install the drum, tire and wheel assembly. Adjust the rear brakes and lower the vehicle.
prev.gif next.gif

Aug 17, 2010 | 1999 Chevrolet Suburban

2 Answers

Parking brake cable stretched beyond adjustment how do you replace


Rear Brake Shoes- You'll need to know how to remove the rear brake shoes to remove the parking brake cable. REMOVAL AND INSTALLATION Amigo and Rodeo
  1. Raise and safely support the vehicle.
  2. Remove the rear wheels.
  3. Remove the brake drums.
  4. Remove the brake return springs.
  5. Remove the leading shoe holding pin and spring, and then the leading shoe.
  6. Remove the self-adjuster and the adjuster lever.
  7. Remove the trailing shoe holding pin and spring.
  8. Disconnect the parking brake cable from the trailing shoe and remove the trailing shoe. Remove the parking brake lever from the trailing shoe. To install:
  9. Attach the parking brake lever to the trailing shoe.
  10. Connect the parking brake cable to the parking brake lever.
  11. Apply a thin coat of high temperature grease to the shoe contact points on the brake backing plate (locations A and C in the accompanying illustration), piston contact surface (B), and self-adjuster (D). Fig. 1: Exploded view of the rear drum brakes — Amigo and Rodeo 93026g56.gif

  12. Position the trailing shoe on the backing plate and install the hold-down pin, spring, and retainer. Don't stretch the return spring when fitting the shoes onto the backing plate.
  13. Connect the upper return spring and the leading shoe to the trailing shoe and position the leading brake shoe on the backing plate.
  14. Install the adjuster assembly and the hold-down pin, spring, and retainer.
  15. Use a brake spring tool to install the lower return spring.
  16. Install the self-adjuster lever and adjuster spring.
  17. Adjust the shoe-to-drum clearance to 0.0098–0.0157 in. (0.25–0.40mm) and install the brake drum.
  18. Check the brake drum for scoring or other wear. Machine or replace as necessary. Check the maximum brake drum diameter specification when machining.
  19. Install the rear wheels. Lower the vehicle.
  20. Road-test the vehicle.
prev.gif next.gif

Aug 17, 2010 | 1997 Isuzu Rodeo

2 Answers

1997 Ford contour rear brake shoe replacment help.


Brake shoe removel:

Depress and turn the retainers for the hold-down springs and pins to remove them from each shoe. Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.

Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.

Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xgUqun
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xdByQ8

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

    Jul 17, 2010 | 1995 Ford Contour

    1 Answer

    Change drum brakes


    Brake Shoe: Service and Repair
    REMOVAL
    1. Raise vehicle and remove rear wheels.
    2. Remove and discard spring nuts securing drums to wheel studs.
    3. Remove brake drums.
    NOTE: If drums prove difficult to remove, retract brake shoes. Remove access plug at the rear of backing plate and back off adjuster screw with
    brake tool and screwdriver.
    4. Remove U-clip and washer securing adjuster cable to parking brake lever.
    5. Remove primary and secondary return springs from anchor pin with brake spring pliers.
    6. Remove hold-down springs, retainers and pins with standard retaining spring tool.
    7. Install spring clamps on wheel cylinders to hold pistons in place.
    8. Remove adjuster lever, adjuster screw and spring.
    9. Remove adjuster cable and cable guide.
    10. Remove brake shoes and parking brake strut.
    11. Disconnect cable from parking brake lever and remove lever.
    INSTALLATION
    1. Clean support plate with brake cleaner.
    2. If new drums are being installed, remove protective coating with carburetor cleaner or brake cleaner.
    3. Clean and lubricate anchor pin with light coat of Mopar multi-mileage grease.
    4. Apply multi-purpose grease to brake shoe contact surfaces of support plate.
    5. Lubricate adjuster screw threads and pivot with spray lube.
    6. Attach parking brake lever to secondary brake shoe. Use new washer and U-clip to secure lever.
    7. Remove wheel cylinder clamps.
    8. Attach parking brake cable to lever.
    9. Install brake shoes on support plate. Secure shoes with new hold-down springs, pins and retainers.
    10. Install parking brake strut and spring.
    11. Install guide plate and adjuster cable on anchor pin.
    12. Install primary and secondary return springs.
    13. Install adjuster cable guide on secondary shoe.
    14. Lubricate and assemble adjuster screw.
    15. Install adjuster screw, spring and lever and connect to adjuster cable.
    16. Adjust shoes to drum.
    17. Install wheel/tire assemblies and lower vehicle.
    18. Verify firm brake pedal before moving vehicle.

    56a4433.jpg

    Aug 12, 2009 | 1997 Jeep Cherokee Country

    1 Answer

    Remove and replace rear brake shoes on 2004 honda accord


    Brake Shoes Removal & Installation To Remove:
    1. Raise and safely support rear of vehicle.
    2. Remove rear wheel assemblies.
    3. Release parking brake.
    4. Remove brake drum.
    Rear brake shoe assembly


    6c57c70.gif
    1. Using an appropriate brake spring tool, unhook upper return spring from rearward brake shoe.
    2. Push retainer springs IN and turn to remove tension pins.
    3. Lower brake shoe assembly and remove lower return spring.
    4. Remove brake shoe assembly from back plate.
    5. Disconnect parking brake cable from lever and remove brake shoe.
    6. Remove parking brake lever from brake shoe.

    To Install:

    d36458c.gif
    1. Install parking brake lever to rearward brake shoe.
    2. Secure lever to brake show with a NEW U-clip.
    3. Pinch U-clip closed.
    4. Connect parking brake cable to rearward brake shoe.
    5. Install self-adjuster lever spring on front brake shoe.
    6. Assemble clevises, adjuster bolt and upper and lower return springs.
    7. Apply a light coat of grease (Molykote 44MA or equivalent) to sliding surfaces.
    8. Install brake shoe assembly onto back plate.
    9. Install tension springs.
    10. Using an appropriate brake spring tool, unhook upper return spring to rearward brake shoe.
    11. Install brake drum.
    12. Install rear wheel assembly.
    13. Lower vehicle.
    14. Adjust self-adjusting brakes by pressing brake pedal several times.

    Jul 13, 2009 | 2004 Honda Accord

    1 Answer

    I need a schematic for the rear brakes on an F150 super cab with 4.6L automatic trans 4wheel drive


    Drum, Rear Brake System Standard Rear Brake
    9969082.gif
    Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
    Heavy Duty Rear Brake
    6dcb5d2.gif
    Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
    The rear drum brakes:
    • Have internal shoes that expand against the brake drum (1126).
    • Are a single-anchor type.
    • Are actuated by one rear wheel cylinder (2262).
    • Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
    • Adjust rear brake shoes and linings (2200) automatically.
    • Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.
    When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
    The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

    Apr 04, 2009 | 1997 Ford F150 Regular Cab

    Not finding what you are looking for?
    1993 Cadillac DeVille Logo

    Related Topics:

    42 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cadillac Experts

    yadayada
    yadayada

    Level 3 Expert

    75077 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7768 Answers

    Are you a Cadillac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...