Question about 1993 Chevrolet C2500

1 Answer

HYDRALIC CLUTCH BLEEDING 1993 CHEVY TRK 2500 ,AFTER REPLACING THE LINE

Posted by on

  • lgibson4 May 11, 2010

    I have had some cars with the same prob, now a few things are. master cylinder is now a suspect, while it had residual pressure all was fine, but when you lost it probs begin, also don,t over look the slave cyl same think. now if you are conviced all is fine and i doubt that it is, check to see if the high pressure pipe from the master cylinder to the slave cyl is going uo in an arch before coming down to the slave cyl. this is a point of many 4wd mainly disco l rovers. a method that i use is to try a plastic hose to the open bleeder and apply a slight vacumn. also or open bleeder place hose oi half filled jar of brake fluid and just pump the clutch slowly. not all the way too the floor just inch or 2 at the most. best of luck hj miame

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,036 Answers

Raise and support vechicle safely.remove slave cylinder.hold slave cylinder at a 45 degree angle.with bleeder screw at it highest point.have a helper fully depress hold clutch pedal.then open the bleeder screw. then close the bleeder screw.and have helper release the clutch pedal repeat the procedure until all of the air is evacuated from the system.keep check on on master cylinder keep fluid level full.to keep air from being drawn through the master cylinder.never release a depress clutch pedal with bleeder screw open.or air will enter the system.

Posted on Jul 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can not bleed clutch on 1987 GMC 2500


There is still air in the system. Try bleeding the m/cyl first by removing the line to the slave cyl and while holding you finger over the opening have someone gently operate the pedal. When you get good fluid past your finger reconnect the line then bleed the slave cyl. as normal.

PLEASE RATE THIS REPLY FOR ACCURACY

Mar 24, 2013 | Cars & Trucks

1 Answer

94 Chevy 2500 Clutch Engagement?


You probably have a hydraulic clutch. A hydraulic clutch has both a master and a slave cylinder. The slave cylinder engages/disengages the clutch plate. You might be low on clutch fluid in the master cylinder, or the system may need to bled similar to bleeding brakes. Worst case is you need a new clutch, pressure plate, and throwout bearing. They should all be replaced when doing a clutch job.

Aug 23, 2012 | Cars & Trucks

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

2 Answers

Can you adjust the clutch pedal on a 1990 full size bronco


The clutch is operated hydraulically, and there is no adjustment. If your problem is that the clutch will not disengage or is hard to disengage you may be low on fluid or have air in the line. There may be a leak either at the master cylinder or the clutch slave cylinder. Bleeding the slave cylinder may restore pedal pressure. If the problem is that the clutch engages high on the pedal the problem is likely a worn clutch disc.

Jul 30, 2011 | 1990 Ford Bronco

1 Answer

I HAVE A MANUEL 2003 CTS.WHILE DRIVING THE CLUTCH WENT DOWN LIKE A 1/4 WAYS TO FLOOR FEELS REAL WEAK.I KNOW ITS HYDRALIC .FEELS LIKE THERES AIR IN THE LINE .LIKE IT NEEDS BLEEDING LIKE...


Unfortunately, it sounds like your pressure plate is going bad. That is the larger part in the following picture. When you depress the clutch pedal it pushes the throw out bearing (the smallest round part) against those center "feelers" and that disconnects the clutch (the next size down round plate) from your engine flywheel.

Normally you would replace all three parts at the same time.

Auto Com Clutch Kit eco31-13122_d.jpg AUTOCOM ECONOMY CLUTCH KIT -- Includes

Jun 24, 2011 | 2003 Cadillac CTS

1 Answer

Is there any way to adjust the clutch on 2006 Kia Spectra5?


YOU HAVE HYDRALIC CLUTCH WHICH IS A CLUTCH MASTER CYLINDER WITH SLAVE CYLINDER.IF YOU HAVING CLUTCH PROBLEMS.CLUTCH IS WORN AND SLIPPING OR YOU HAVE LOW FLUID LEVEL IN CLUTCH MASTER CYLINDER.WHICH CAUSES AIR GET IN HYDRALIC SYSTEM.CAUSING CLUTCH PROBLEMS.IF CLUTCH MASTER CYLINDER IS LOW ON FLUID.CHECK HYDRALIC LINE ON SLAVE CYLINDER TO CLUTCH MASTER CYLINDER FOR FLUID LEAKS.

Aug 03, 2010 | 2007 Kia Spectra5

1 Answer

1993 chevy silverado 4x4 4.3 4sp. clutch issue


somthing is leaaking down then from what your desribing. probably the slave is it leaking fluid into the bellhousing?? these do trap air badly too because the bleeder is on the rear of the slave and it runs down hill with the drive train. jack the rear of truck as high as possible to get the air to rise to bleeder and bleed again

Aug 26, 2009 | 1995 Chevrolet Silverado 2500

1 Answer

Need to bleed the hydralic clutch system on a 1993 chevy 2500 trk .Replaced old line,now need to bleed the rest of the air out


Should be a bleeder on the slave cylinder. remove the cover on the master and open the slave and let drip until fluid drops sdteady and no sign of air. Close slave and close master after replenishing the fluid. The first time you press on the pedal go slow and release real slow. Then you are off and clutching. Good Luck

Jul 19, 2009 | 1993 Chevrolet C2500

1 Answer

Clutch needs to be adjusted on 1995 Chevy 2500 Pickup


You might still have a little air in the system, try bleeding it one more time. There isn't any adjustment like on a cable clutch system.

Jun 07, 2009 | 1995 Chevrolet C/K 2500

1 Answer

1995 gmc sierra clutch pressure problem


could be wrong here but sure sounds like its out of fluid at the "master cylinder" look near the brake master cylinder for a seperate little container for the clutch. bleeding is tricky because it is small and wants to run out of fluid quick. you have to keep adding each time you bleed. Hope I helped. Thanks

Feb 26, 2009 | 1995 GMC Sierra C1500

Not finding what you are looking for?
Cars & Trucks Logo

1,384 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...