Question about 1993 Chevrolet C2500

1 Answer

Need to bleed the hydralic clutch system on a 1993 chevy 2500 trk .Replaced old line,now need to bleed the rest of the air out

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 3,433 Answers

Should be a bleeder on the slave cylinder. remove the cover on the master and open the slave and let drip until fluid drops sdteady and no sign of air. Close slave and close master after replenishing the fluid. The first time you press on the pedal go slow and release real slow. Then you are off and clutching. Good Luck

Posted on Jul 19, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 14036 Answers

SOURCE: HYDRALIC CLUTCH BLEEDING 1993 CHEVY TRK 2500

raise and support vechicle safely.remove slave cylinder.hold slave cylinder at a 45 degree angle.with bleeder screw at it highest point.have a helper fully depress hold clutch pedal.then open the bleeder screw. then close the bleeder screw.and have helper release the clutch pedal repeat the procedure until all of the air is evacuated from the system.keep check on on master cylinder keep fluid level full.to keep air from being drawn through the master cylinder.never release a depress clutch pedal with bleeder screw open.or air will enter the system.

Posted on Jul 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can not bleed clutch on 1987 GMC 2500


There is still air in the system. Try bleeding the m/cyl first by removing the line to the slave cyl and while holding you finger over the opening have someone gently operate the pedal. When you get good fluid past your finger reconnect the line then bleed the slave cyl. as normal.

PLEASE RATE THIS REPLY FOR ACCURACY

Mar 24, 2013 | Cars & Trucks

1 Answer

How to bleed a hydralic clutch on a 2001 chevy blazer


You must reverse bleed it. Go here to learn how. You will need to buy the tool pictured.

Dec 05, 2012 | 2001 Chevrolet Blazer

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

1 Answer

When I step on the clotch it gets stuck and dosent come back out


CHECK CLUTCH MASTER CYLINDER.SOUND LIKE BRAKE FLUID LOW.IF BRAKE FLUID LOW LOOK FOR LEAKS AROUND CLUTCH MASTER CYLINDER AND CHECK FOR LEAKS AROUND BRAKE LINES AND CHECK FOR LEAKS AROUND CLUTCH RELEASE CYLINDER HYDRALIC LINE FITTING. REASON PEDAL GOING TO FLOOR YOU HAVE FLUID LEAK WHICH WILL CAUSE AIR TO GET IN THE CLUTCH HYDRALIC SYSTEM. YOU HAVE TO LOCATE LEAK FIX AND BLEED THE CLUTCH HYDRALIC SYSTEM.

Dec 27, 2010 | 1999 Volkswagen Passat

2 Answers

Well I have a 2000 Mercury Cougar 2.5L V6 DOCH engine 5 speed and I know its a hydraulic clutchsystem it has,but the problem Im having is getting the car into gear when the car is on, I feel the clutch...


either you have air in the hydraulic lines or there is a problem with the final linkage. Is the slave leaking? Have you had to add fluid to the reservoir? Was the reservoir ever found empty? If yes, fix leak and bleed system. If no, problem is probably in the fianl linkage after the slave. Slave my be loose or linkage worn out? Let us know what you find and if you need more help.

Oct 08, 2010 | 2000 Mercury Cougar

1 Answer

HI, I HAVE A 1995 PROBE 2.0 16V,& I JUST RECENTLY REPLACED THE CLUTCH & PRESSURE PLATE.JUST YESTERDAY WHEN I WANTED TO DRIVE IT,I COULD NOT SEEM TO SELECT ANY GEARS TO PULL AWAY. WHEN I PRESSED...


If hydralic, it sound like you have air in the hydralic line. You need to bleed it off at the slave cylinder (gearbox end of the line)

If cable type, then you may need to reset the ratchet on the clutch pedal.

Dec 07, 2009 | 1994 Ford Probe

1 Answer

1993 chevy silverado 4x4 4.3 4sp. clutch issue


somthing is leaaking down then from what your desribing. probably the slave is it leaking fluid into the bellhousing?? these do trap air badly too because the bleeder is on the rear of the slave and it runs down hill with the drive train. jack the rear of truck as high as possible to get the air to rise to bleeder and bleed again

Aug 26, 2009 | 1995 Chevrolet Silverado 2500

1 Answer

HYDRALIC CLUTCH BLEEDING 1993 CHEVY TRK 2500 ,AFTER REPLACING THE LINE


raise and support vechicle safely.remove slave cylinder.hold slave cylinder at a 45 degree angle.with bleeder screw at it highest point.have a helper fully depress hold clutch pedal.then open the bleeder screw. then close the bleeder screw.and have helper release the clutch pedal repeat the procedure until all of the air is evacuated from the system.keep check on on master cylinder keep fluid level full.to keep air from being drawn through the master cylinder.never release a depress clutch pedal with bleeder screw open.or air will enter the system.

Jul 19, 2009 | 1993 Chevrolet C2500

1 Answer

Chevy l989 4X4 5 speed manual clutch not working


Almost every time a clutch is replaced in a GM with hydraulic release system that system is replaced as well. You can try, and try, and try again to bleed it, but you will eventually replace the clutch slave and master cylinders. Once the slave is allowed to fully extend, it is then virtually impossible to make it function correctly again.

Jul 08, 2009 | 1998 Volkswagen Passat

1 Answer

Clutch needs to be adjusted on 1995 Chevy 2500 Pickup


You might still have a little air in the system, try bleeding it one more time. There isn't any adjustment like on a cable clutch system.

Jun 07, 2009 | 1995 Chevrolet C/K 2500

Not finding what you are looking for?
Cars & Trucks Logo

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...