Question about 2003 Ford Crown Victoria

1 Answer

2005 P71 LEFT HI BEAM DOES NOT WORK. RELACED THE BULB AND STILL DOES NOT WORK. CAN I JUMP A WIRE FROM THE RIGHT SIDE TO THE LEFT SIDE TO MAKE IT WORK?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 54 Answers

Is a quick fix but will not solve the problem of why and in the long run you could overload the wire carrying voltage to your left high beam causing both to not work

Posted on Jul 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2008 ford ranger headlight relay bad? Lamps do not light up, checked BULBS..OK no left highbeam Left and right lamp fuses ok and hi/lo 30a fuse ok


Did you check the fuse circuit for voltage, use a testlite or something.
I posted part of headlamp wiring. You understand your dimmer switch is involved in the circuits.
2008-ford-ranger-headlight-relay-tigo4fxke2krqgp04tlk3h2i-1-0.jpg

Oct 22, 2016 | 2008 Ford Ranger

1 Answer

The low beam on passenger side does not work,high beams work on both sides


Hi Greg:
I'd pull the bulbs from both sides and switch them.
You'll know right away if the bulb is the problem.
If low beam on the passenger side still does not work, then there is either a broken wire or bad connection. Make sure the area where the bulb fits into the socket is clean.
Usually there is only one bulb that has both high and low beam.

May 27, 2015 | 2005 Cadillac Deville

2 Answers

What would cause the low beam headlight not to work when all other lights work?


If you have standard halogen bulbs:

  1. Burned out light bulb; or
  2. Fried wires between the dashboard wiring harness and the headlight bulb connectors; or
  3. Fried headlight bulb connectors.
If you have HEI emitters:
  • Failed ballast.

May 11, 2015 | 2002 Mercury Grand Marquis

1 Answer

Replacing low beam bulb in a 2005 mazda3. How do clips work on the new bulb


Hi ,
The buld is retained by a light wire frame under a slight spring tension, a clear view would help but it's usually a slight push (th the front) and a small movement either left or right to release the srping tension. Don't handle the bulb (oil from skin contamination) and possible refer to owners handbook !
Good Luck

Dec 13, 2010 | 2005 Mazda 3

1 Answer

2002 gmc Yukon denali Left head light only works on Hi-beam. Also left licenses plate light not working as well


i would try replacing those bulbs,the headlights are dual filiment and can work on just high beam and not on low beam,so start there and replace your bulbs

Sep 30, 2010 | 2002 GMC Yukon Denali

1 Answer

How to change the low beam bulb on a 2005 buick rendevous?


Hi: Open Your Hood ,And From The Inside of Your Engine Compartment Look For a Wires Running To Both Left And Right Front Lights Theres a Bulb Socket attached to Your Head Lights ,Theres not a Lot of Room to work With ,But Reach in With Your Hand And Use Your Fingers To Turn the Elecrical Head Light Socket Counter Clockwise until the Bulb Socket Stops Then Pull Out The Bulb Socket ,Pull Old Bulb Or Bulbs Out .To Relace With New. These are Halogen Bulbs, Be Careful And Try Not Touching the Bulbs with Your Bare Fingers. You can Put a Real Thin Gloves On to Push Bulbs Back Into The Sockets.This Should Get You You could have 2 Bulbs Per Side 1 Low 1-High . Hope This Helps You, Let Me Know by Voting on my Quality of Assistance.

From the WYOCWBOY

Jun 01, 2010 | 2005 Buick Rendezvous

2 Answers

Left side low beam not working


check low beam fuse and relay

Apr 14, 2009 | 2002 Cadillac Sts

2 Answers

Have High beams, but right low beam doesn't work


yes you are right it is the blub that need to be relace

Feb 01, 2009 | 1987 Toyota Camry

1 Answer

How to change my headlights on Honda 2005 CRV


easy cheesy! Ive changed mine twice. The headlights are small bulbs. Make sure you get the right one (hi-beam vs low-beam). Unplug connector at back of bulb / headlamp unit, remove rubber weather seal (pops right ot). The bulb is held in with a small wire clip that is hard to get back on but can be done. Its spring loaded. Drop wire clip, turn bulb assya 1/4 turn, and it comes right out. Remove bulb from holder and replace. Reverse steps and VOILA!

Dec 27, 2008 | 2005 Honda CR-V

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...