Question about 1995 Ford Explorer

1 Answer

I need to know where to find the rubber seal that goes between fuel pump and the fuel assembly? i have checked all parts stores an they do not have it ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,114 Answers

1995 Ford Explorer - Carter Fuel Pump Lock Ring
Try going to Auto Parts Warehouse. Plug in your vehicle info.
Go to" fuel pump", and on page three is the lock ring and gasket. Don't know if this part is a fit for your vehicle, but there's several on line auto parts stores to look in.
Hope this helps....

Posted on Jul 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change feul pump 97 chevy lumina 3.1 l


You must remove the fuel tank which is underneath the trunk. Here's the procedure for removing the pump.

REMOVAL:

1. Before servicing the fuel pump the fuel system pressure must be relieved.
2. Disconnect the negative battery cable.
3. Raise the car on a hoist.
4. Remove the fuel tank.
5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal.

NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.

INSTALLATION:

1. Push the fuel pump assembly into the attaching hose.
2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal.

NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.

3. Install cam lock over the assembly and lock by turning clockwise.
4. Reinstall fuel tank.

May 09, 2017 | Cars & Trucks

1 Answer

How to replace a gas tank


The two large straps hold the tank under the truck. You will need to raise the truck up enough that you can not only get under it but also have room to get the old tank out and get the new tank in. You also need to support the tank after you remove the straps at the fuel lines will still be connected and you do not want to damage them. Now is the time to remove the fuel lines, you will need a special tool that releases the the fuel lines, it is round and has a slit up one side to allow it to be placed onto the line. Once the tool is on the line you will push it towards the fat part of the line pushing the extended part of the tool into the locking assembly to release it. The tools are easily purchased at the part store but there are many sizes available so I would suggest getting a kit so you know you have the correct sizes. There are two lines, each are a different size but remove the same way. Most often you will have to work the release tools around as they never release easily. Once you get the fuel lines off you can unplug the electrical connector feeding the fuel gauge and pump and lower the old tank out. Revers the procedure to re install the new tank.You will also likely need to switch over your level sending unit and pump assembly to the new tank. The assembly is the unit the lines plug into and you can remove it by using a small pry bar and hammer to rotate the large ring that holds it in. Again you reverse this process to re install in the new tank making sure the rubber gasket sit correctly for the proper seal. If the tank sending unit is not sealed it will set an evap code and turn the check engine light on. .

Sep 23, 2014 | 2001 GMC Sonoma Extended Cab

2 Answers

Leaking fuel pump


If the fuel is leaking into the car you will need the replace the seal on the top on the pump assembly not the seals on the pump itself but before changing the seal just double check the fuel lines are tight and the leak is actually from the fuel splashing out of the tank. The seal your after is referred to as the pump assembly oring ( big rubber oring around the top of the assembly a smear of silcone can be used as a temporary fix but erge you to get it fix properly as soon as possible and fuel fumes in the cabin can be extremely deadly)
Hope this helps

Jan 15, 2014 | 2003 Nissan Altima

1 Answer

My digital gas gage reads full all the time I have to go by my miles and sometimes that don't work and I run out of gas..how do I fix my problem


This is a common problem and to correct this problem will require the replacement of the fuel sending unit. The fuel sending unit is inside the fuel tank and has the fuel pump mounted in it. This requires the removal of the gas tank and then the fuel sending unit can be removed from the tank.

REMOVAL AND INSTALLATION Fig. 1: Fuel pump unit 8470h037.gif
  1. Disconnect the negative battery cable.
  2. Relieve fuel system pressure.
  3. Remove fuel filler cap to release fuel tank vapors. Leave cap off until repairs are completed. Gasoline fuel vapors are extremely flammable. Ensure that fuel is stored in a container that can be properly sealed. Never store fuel in an open container. Store container in a safe place away from heat.
  4. Remove fuel tank by performing the following:
    1. Step 1: Drain fuel from the tank into an approved container for storage.
    2. Step 2: Raise and safely support the vehicle.
    3. Step 3: Remove rear stabilizer bar at links, pivot bar downward.
    4. Step 4: Remove hoses and pipes from tank unit.
    5. Step 5: Remove hoses at tank from filler and vent pipe.
    6. Step 6: Disconnect tank unit harness from rear body harness.
    7. Step 7: Support fuel tank and disconnect 2 fuel tank retaining straps.
    8. Step 8: Remove tank from vehicle.
  5. Remove sending unit, gasket and pump assembly by turning cam lock ring counterclockwise. Lift assembly from fuel tank and remove fuel pump from fuel tank sending unit.
  6. Pull fuel pump up into attaching hose while pulling outward away from bottom support. Take care to prevent damage to rubber insulator and strainer during removal. After pump assembly is clear of bottom support, pull pump assembly out of rubber connector for removal. To install:
  7. Push fuel pump assembly into attaching hose.
  8. Install fuel tank sending unit and pump assembly into tank assembly. Use new O-ring seal during reassembly.
  9. Install cam lock over assembly and lock by turning clockwise.
  10. Support tank and position in vehicle. Install tank straps and secure with retaining bolts. Tighten to 25 ft. lbs. (33 Nm).
  11. Connect tank unit harness to body harness.
  12. Connect hoses to filler and vent pipes. Tighten clamps.
  13. Connect hoses and pipes to tank unit.
  14. Connect rear stabilizer bar to links. Tighten bolts to 42 ft. lbs. (58 Nm).
  15. Lower vehicle.
  16. Refill tank and install filler cap.
  17. Connect negative battery cable.
  18. Start engine and check for leaks.

Dec 24, 2010 | 1992 Oldsmobile Toronado

1 Answer

Can I access the fuelpump through the trunk on a 94 concours c4.6


According to the instructions, it is not accessible through the trunk on the 94 Cadillac --- REMOVAL AND INSTALLATION Fig. 1: Fuel pump unit 8470h037.gif
  1. Disconnect the negative battery cable.
  2. Relieve fuel system pressure.
  3. Remove fuel filler cap to release fuel tank vapors. Leave cap off until repairs are completed. Gasoline fuel vapors are extremely flammable. Ensure that fuel is stored in a container that can be properly sealed. Never store fuel in an open container. Store container in a safe place away from heat.
  4. Remove fuel tank by performing the following:
    1. Step 1: Drain fuel from the tank into an approved container for storage.
    2. Step 2: Raise and safely support the vehicle.
    3. Step 3: Remove rear stabilizer bar at links, pivot bar downward.
    4. Step 4: Remove hoses and pipes from tank unit.
    5. Step 5: Remove hoses at tank from filler and vent pipe.
    6. Step 6: Disconnect tank unit harness from rear body harness.
    7. Step 7: Support fuel tank and disconnect 2 fuel tank retaining straps.
    8. Step 8: Remove tank from vehicle.
  5. Remove sending unit, gasket and pump assembly by turning cam lock ring counterclockwise. Lift assembly from fuel tank and remove fuel pump from fuel tank sending unit.
  6. Pull fuel pump up into attaching hose while pulling outward away from bottom support. Take care to prevent damage to rubber insulator and strainer during removal. After pump assembly is clear of bottom support, pull pump assembly out of rubber connector for removal. To install:
  7. Push fuel pump assembly into attaching hose.
  8. Install fuel tank sending unit and pump assembly into tank assembly. Use new O-ring seal during reassembly.
  9. Install cam lock over assembly and lock by turning clockwise.
  10. Support tank and position in vehicle. Install tank straps and secure with retaining bolts. Tighten to 25 ft. lbs. (33 Nm).
  11. Connect tank unit harness to body harness.
  12. Connect hoses to filler and vent pipes. Tighten clamps.
  13. Connect hoses and pipes to tank unit.
  14. Connect rear stabilizer bar to links. Tighten bolts to 42 ft. lbs. (58 Nm).
  15. Lower vehicle.
  16. Refill tank and install filler cap.
  17. Connect negative battery cable.
  18. Start engine and check for leaks.
prev.gif next.gif

Aug 26, 2010 | Cadillac Escalade ESV Cars & Trucks

2 Answers

I am getting no diesel into my fuel filter is their a electric pump in my tank or is the fuel pump part of the injector pump


Fuel Pump REMOVAL & INSTALLATION Navajo and B Series Pick-up Models NOTE: To gain access to the fuel pump, it is necessary to remove the fuel tank.
  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
  4. Remove the fuel pump and bracket assembly.
  5. Remove the seal gasket and discard it. To install:
  6. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove. Fig. 1: Fuel pump and sending unit used on the B Series Pick-up regular cab 89685g02.gif
    Fig. 2: Fuel pump and sending unit used on the B Series Cab Plus Pick-up 89685g03.gif
    Fig. 3: Fuel pump and sending unit used on the Navajo 89685g04.gif

  7. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  8. Install the tank in the vehicle.
  9. Install a minimum of 10 gallons of fuel and check for leaks.
  10. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF, then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
  11. Remove the pressure gauge. Start the engine and check for fuel leaks.
MPV Models
  1. Relieve the fuel system pressure and disconnect the negative battery cable.
  2. Remove the rear seat and lift up the rear floormat. Remove the fuel pump cover.
  3. Disconnect the sending unit/fuel pump assembly electrical connector and the fuel lines.
  4. Remove any dirt that has accumulated around the sending unit/fuel pump assembly so it will not enter the fuel tank during removal and installation.
  5. Remove the attaching screws and remove the sending unit/fuel pump assembly.
  6. If necessary, disconnect the electrical connectors and the fuel hose and remove the pump from the sending unit assembly.
  7. Installation is the reverse of the removal procedure. Be sure to install a new seal rubber gasket. Fig. 4: Remove the rear seat and floormat to service the fuel pump 90975g06.gif
    Fig. 5: Removing the fuel pump assembly 90975g07.gif
prev.gif next.gif

Aug 17, 2010 | 1995 Mazda MPV

1 Answer

How to replace fuel pump 91 lesabre


Removal & Installation The fuel pump is located in the fuel tank. The fuel tank must be removed from the vehicle in order to access the pump.
  1. Properly relieve fuel system pressure.
  2. If not already done, disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. Safely drain and remove the fuel tank assembly, as outlined later in this section.
  5. If necessary, detach the quick-connect fittings from the fuel sender assembly and remove the fuel lines.
  6. Remove the fuel gauge sender and pump assembly by turning the cam locking ring counterclockwise. It may be necessary to use a spanner wrench, such as tool J-24187, to perform this.
  7. Carefully lift the assembly from the fuel tank, then remove the fuel pump from the fuel gauge sender unit.
  8. Remove the sender O-ring from the top of the sender and discard.
  9. Disconnect the pump wires, hose clamps and the clamp from around the pump body.
  10. Pull the pump assembly out of the rubber connectors.
  11. Inspect the fuel pump attaching hose for any signs of deterioration, and replace as necessary.
  12. To install:
    1. Push the fuel pump assembly into the attaching hose. Attach the pump electrical wires and fasten the hose clamps to the attaching hose and around the pump body.
    2. Place the fuel tank sender and pump assembly into the fuel tank. Use a new O-ring seal during assembly.
    3. Place the cam lock over the assembly, then lock by turning clockwise, using a suitable spanner wrench, if necessary.
    4. If removed, attach the fuel sender fuel line quick-connect fittings.
    When installing the fuel tank, make sure all rubber sound isolators or anti-squeak spacers are replaced in their original locations.
    1. Install the fuel tank, as outlined later in this section.
    2. Refill the fuel tank.
    3. Connect the negative battery cable.
    4. Turn the ignition switch to the ON position to pressurize the fuel system and check for leaks.

Oct 10, 2009 | 1991 Buick LeSabre

1 Answer

I need to replace the fuel pump in my 940 Volvo.


Disconnect battery ground strap before beginning to work on the fuel/electrical system. Do not smoke or have anything in the area which can ignite or cause sparks

  1. Drain enough fuel from tank to prevent spilling, no more than 4 gallons (16 liters) of fuel should remain. Use suitable pumping equipment.
  2. Remove floor mat and panel from trunk.
  1. Disconnect wiring harness connector to sending unit. Remove wires from connector.
  2. Disconnect ground wire to sender. Push wires through grommet.
  3. Remove cover for access to tank sending unit.
  1. All models: Disconnect from the fuel tank sending unit:
    1. Breather hose C
    2. Return hose A
    3. Supply hose B
    4. Filler hose D
    5. Wiring harness from clip E
  1. Clean area and unscrew fuel tank sender/pump cap or equivalent. Remove tank sender/pump and seal.
  2. Remove pump from sender/pump assembly.
INSTALLATION
  1. Inspect the pump for damage, feed pump hose and wiring for wear. Replace as needed.
  2. Install new pump to sender/pump assembly.
  3. Install rubber seal in neck of tank. Lubricate inside of seal.
  1. Install fuel tank sender/pump unit. Align it with the moulded joint (arrows) on tank.
  2. Apply rustproofing compound to exposed metal portions of tank sender.
CAUTION : With tape or rubber caps, protect fuel sender openings from overspray.
  1. Torque fuel tank sender/pump lock ring to: 22 ft-lb (30 Nm)
  2. Reassemble components in reverse order. Use tie straps to secure all hoses and wiring.

Jun 04, 2009 | 1995 Volvo 940

1 Answer

I need to replace the fuel pump in my 1985 Chevy S10 pickup, need all help. What is the procedures?


EXACT PROCEDURE ! Please Rate Me Fairly for this!! Thank you And Good Luck !!


ELECTRIC PUMP

REMOVAL
  1. Before servicing the fuel pump the fuel system pressure must be relieved. See: Fuel Pressure Release
  2. Disconnect the negative battery cable.
  3. Raise the car on a hoist.
  4. Remove the fuel tank. See Fuel Tank / Service and Repair.
  5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
  6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal. NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.
INSTALLATION
  1. Push the fuel pump assembly into the attaching hose.
  2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal. NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.
  3. Install cam lock over the assembly and lock by turning clockwise.
  4. Reinstall fuel tank.
MECHANICAL PUMP

REMOVAL and INSTALLATION

NOTE: To ease pump installation, rotate the camshaft so the camshaft eccentric is out of the way of the fuel pump rocker arm.

  1. Disconnect fuel lines from fuel pump.
  2. Remove fuel pump mounting bolts and the fuel pump.
  3. Remove all gasket material from the pump and block gasket surfaces. Apply sealer to both sides of new gasket.
  4. Position gasket on pump flange and hold pump in position against its mounting surface. Make sure rocker arm is riding on camshaft eccentric.
  5. Press pump tight against its mounting. Install retaining screws and tighten them alternately.
  6. Connect fuel lines. Then operate engine and check for leaks.

Mar 22, 2009 | 1985 Chevrolet S-10

3 Answers

2005 Buick Rendezvous Fuel Gauge


well the gage is made of rubber it could be sticking no other way than to replace the gage itself/ please rate my response thank you very much

Jan 31, 2009 | 2002 Buick Rendezvous

Not finding what you are looking for?
1995 Ford Explorer Logo

Related Topics:

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...