Question about 1991 Toyota Corolla
44 ft lbs.is your torque.but you have to do it in 3 steps.first you torque it to 22 ft lbs.then an additional 90 degrees + an additional 90 degree turn.
Posted on Jul 19, 2009
There are apparently 2 different 1.6 motors.
The 4AFE: front 8-6-1-3-9
of vehicle 10-4-2-5-7
tighten in 3 steps, 1. 20 ft lbs 2. 30 3. 44
The 4AGE front 8-4-2-5-9
of engine 10-6-1-3-7
tighten in 5 steps: 1, 10 2. 15 3. 22 4.an additional 90degrees and 5. an additional 90 degrees again.
Posted on Jul 19, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The 2002 2.4 engine head bolts are 'torqued to distance'.
First, install all the bolts, and, in a sequential fashion, starting at the innermost, working outward, torque all bolts to 70 N-m/806 kgf-cm/58 foot lbs.
Next, mark the front side of each head bolt with a dot of paint. Retighten te cylinder head bolts 90 degrees, starting at the inner 2, and working outward.
We hope that this helps you out.
Posted on Dec 29, 2009
SOURCE: torque specs for toyota tercel
Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using FixYa. Roger
Posted on Apr 15, 2009
The toyota previa uses a formed silicone gasket for the valve cover and the cover is held in place by metric shoulder bolts ( 10mm). The valve gasket leaks because you can't get enough preload on the bolts to re-seat the old gasket when it gets old and shrinks. The shoulder bolts only allow you to tighten the gasket enough to seat the shoulder on the bolt. If you continue to torque down the suspected bolts, you will snap the bolt off ( don't ask me how I know this ). You can either 1.)replace the old gasket with a new one or 2.) remove the existing bolts around the leak area and put in new metric bolts that do not have a shoulder. You may want to put in a small sleeve into the existing bolt hole but shorter than the thickness of the valve cover to account for the smaller diameter bolt. You can now torque down the bolt and get enough preload to seal the valve cover without removing the old gasket. Make sure you use a torque wrench ( in-lbs) or be very careful not to snap these small valve cover bolts.
Posted on Jul 15, 2009
Tips for a great answer:
Dec 14, 2016 | 1992 Toyota Tercel
Sep 27, 2013 | 1992 Ford Ranger
Oct 11, 2012 | 1992 Dodge Spirit
Mar 06, 2011 | 1992 Toyota 4Runner
May 12, 2010 | 1998 Toyota Sienna
Apr 17, 2009 | 1992 Mercedes-Benz E-Class
Jan 21, 2009 | 1996 Toyota Tercel
Dec 09, 2008 | 1992 Pontiac Grand Prix
484 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: