Hi can anyone give me the torque specs for a Ford Bantam 1.3, cylinder head, big ends and main bearings. It's a 1997 model

https://www.google.com/search?q=Ford+Courier+F8+motor+torque+settings

Torque setting for Ford Courier F8 motor from main bearing

Fixya https://www.fixya.com > Forum > Cars & Trucks > Ford
10 hours ago - Main Bearings Torque specs. 40-43 Ft. Lbs. Cylinder Head Torque specs. 56-60 Ft. Lbs. Read full answer. Oct 05, 2009 • ...

What are the torque settings for a 1997 ford courier 2.2

JustAnswer https://www.justanswer.com > Australian Car Repair
Jul 1, 2021 - Tighten special flywheel-to-crankshaft bolts to 73-87 Nm (54-64 ft. lbs.). 35.If equipped, install clutch disc and clutch pressure plate and ...

1 answer · Top answer: TORQUE SPECIFICATIONS Connecting Rod [https://my.alldata.com/repair/#/repair/vehicle/26150/component ...

1.8 ford courier 8valve torque settings on cylinder head

Fixya https://www.fixya.com > ... > Ford > Expedition
Sep 4, 2008 - First torque value is 58 ft lbs.....then final torgue is 72 ft lbs. Posted on Mar 21, 2009. 0.

Torque Settings

Kiwi Cylinder Heads Ltd https://www.cylinderheads.co.nz > torque-settings
Cylinder Head Torque Settings.

Torque Specifcations

MAHLE Aftermarket https://www.mahle-aftermarket.com > torque3
Make. Liter CID. Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. ACURA. 1.6. 97. D16A1. 86-89. 23 FT/LBS. 40 FT/LBS. 22, 47 FT/LBS.
124 pages
..

https://www.google.com/search?q=2012+chevrolet+captiva+2.2+VCDi+diesel+cylinder+head+torque+specs

https://www.google.com/search?q=2012+chevrolet+captiva+2.2+VCDi+diesel+big+end+torque+specs

Not too much information on the 2.2 diesel. A service manual is the best idea.

..

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

A cheap shop manual will have this and much more. If you are in this deep you probably need one.

Main bearing stage 1: 25NM, stage 2: 50NM
Big-end bearing stage 1: 14NM, stage 2: 28NM
Cylinder head stage 1: 30NM, stage 2: 60NM

1997 Toyota Prado 5VZ-FE
Cylinder head bolts:
Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Write your answer...please can give me torque settings for ford bantam 1.3 rowcam cylinder head.
Amos

This site has all the torque specs you should need make sure this is the correct engine.

http://www.davidfarmerstuff.com/C6Z06-Torque.pdf

I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Torque sequence:
Step 1: Torque 29 to 34 Ft/Lbs
Step 2: Torque an additional 90 to 120 degrees