2001 Chrysler Sebring convertible is it possible that if the fuel pump is bad that it would cause it to NOT be able to go over 2500RPMs

SOURCE: 2000 chrysler sebring convertable top will go down but will not

Typically, when when this happens, the system is low on fluid and/or must be bled. Here are the procedures:
Lower the top to the full down position.

1. Remove the rear seat cushion, seat back and inner quarter trim panels. Pull up sharply on the seat cushion at the front about midway between the middle of the seat and the outside edges. The seat back is held in by nuts. The quarter trim panels are held in by screws I think.
2. Remove the cylinder mounting brackets and remove the cylinders from the trunnion pivot mounts.
3. Rotate the cylinders 180 degrees (the hose fittings will now face to front of the vehicle.
4. Disconnect the motor/pump retaining clips from the body.
5. Rotate and raise the motor/pump assembly so the reservoir is in the up position. The rubber filler plug will be at the top.
6. Raise motor/pump fitting to at least 2 inches above the horizontal rear seat back reinforcement.
7. Tilt the motor/pump assembly to approximately the 10 o'clock position, with the rubber filler plug still at the top CAUTION: THE MOTOR/PUMP ASSEMBLY MUST REMAIN IN THE CURRENT POSITION UNTIL THE RUBBER FILLER PLUG IS REINSTALLED IN THE Step 12.
   
8. Remove the rubber fill plug from reservoir.
9. Fill the hydraulic system by adding Dexron 2 Automatic Transmission Fluid to the bottom of the fill hole CAUTION: DO NOT OPERATE THE TOP SWITCH IN THE UP (CLOSING THE TOP) DIRECTION.
   
10. With two people, activate the top switch in the down (opening the top) position to fully retract the cylinder rods and hold for approximately 5 seconds, until the motor/pump stalls. A percolating or gurgle sound/feeling is an indication that the procedure is working.
11. Top off the motor/pump with Dexron 2 and insert the filler plug.
12. Install the motor/pump assembly into the vehicle mounting bracket.
13. Rotate the cylinders back to the original position (hose fitting rearward)
14. Install the motor/pump lead and hydraulic line clips (the hydraulic line clips are to assist in the production process) to ensure that the seat back/seat cushion do not pinch the lines. If the sticky side is no longer holding to the floor pan, the clips can be left off.
15. Ensure that the bushing is still on the trunnion pivot mount and bracket. Tap the top switch in (raising the top) to get the cylinder trunnion onto the trunnion pivot mounts, if needed.
16. Install cylinder mounting brackets.
17. Raise and lower the top to ensure proper operation.
18. Install the inner quarter panels, and the rear seat back and cushion.
19. And Just a fair warning here - you WILL spill fluid inside your car. If you manage not to, I want to know how. I cover everything with garbage bags because there have been a few instances where I accidentally hit the button the wrong way and that stuff went EVERYWHERE. Be careful and good luck.

SOURCE: replace air filter 2002 Chrysler Sebring convertible

you need to loosen the clamp on the throttle body and unplug the map sensor then there are two clips on the other end pull that out and you should be able to pull the filter out you don't need to take the box off.

SOURCE: 2002 Sebring Convertible Start/Fuel fuse blows intermittently

HAVE SEEN THIS BEFORE AND THE STARTER HAS BEEN THE CULPRIT..HAVE NEVER REPLACED A FUEL PUMP ON ONE OF THESE VEHICLES AT ALL

Testimonial: "I replaced the starter. This job is quite substantial. Also found the nut connecting the cable to the starter coil was not tight. I think it is fixed."

SOURCE: How do I replace the water pump on a 2003 Chrysler

Dont try this at home. Get a shop to replace it and check the timing chain components. If its not done right, bent valves wil be your New Years present. I recommend this. http://www.fix27engine.com/

SOURCE: need the crankshaft main bearing torque specs and

Hello tlittle3: My name is Roger and I will help you.See the attached image. Be sure to follow steps as it is very inportant. You will notice that you need to index some of the bolts. That is merely turning the bolt a specified degree. The crankshaft tie bolts are the bolts that are in the side of the block. install horizontal. Shold you need further help please just ask. Please rate the answer you received. Thank You for using Fix Ya. Roger

Testimonial: "thanks that what i needed"