Question about 2003 Kia Sedona

1 Answer

Changing the mirror

Can not fit passanger mirror (glass only) 2003 Sedona. Any advice? looks like the small pins do not fit the original fittings. Part bought from the dealer.

Posted by on

  • wucash Jul 23, 2009

    Thanks cookieeye! I did not have enough patients and had to cut a little bit of round part which the glass is attached. It was nightmare; trust me it did not fit! There were few people looking at it and no solution. I had to cut it a bit. It is in place now and works ok, so... job done. Thank you anyway.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,071 Answers

Just make sure it is lined up and no other pieces broken

Posted on Jul 23, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I change the glass in the outside mirror on a 2003 Lincoln towncare

behind the piece of glass there is a black plastic that the glass sticks to if you push it to one side stick your fingers behind it and pull you will disconnect the glass retainer from the mirror motors bracket do this on both sides of the mirror and make sure you don't lose the little barrel shaped arms that snap the glass retainer into the window motor housing where glove for broken glass splinters sometimes it's best to put those barrel arms in then press the glass in but I would say it's better to try to fit the arms in while attached to the glass it depends how big your hands/fingers are for the space allowed to get it in GOOD LUCK STEPHEN

Feb 04, 2015 | 2003 Lincoln Town Car

1 Answer

How do I fit a new mirror to the wing mirror on my kia sedona

are you talking about the mirror insert? or the whole mirror assembly? if it's the assembly open the door and look at the black trimpiece pop it off and you'll see 3 10mm bolts and a connector remove them and the whole mirror comes off. If its just the glass insert get some sand paper and sand the holding tabs a little then use any type of grease and put it on the base that you are attaching it to then try to line it up and start on 1 corner i use a rad hose pick tool to support the base as i press the glass into place.

May 07, 2010 | 2003 Kia Sedona

1 Answer

2003 subaru outback mirror glass replacement

You need some bathtub silicone sealer and some black electrical tape and a couple of small wooden blocks. Carefully break out the cracked mirror. WEAR gloves and glasses when you do this and have a bucket to catch the falling glass. Make sure the mirror back is clean and put a bead of silicone around the back of the new mirror. Keep it about 1/4 inch from the edge and some dabs in the center portion. Place the mirror on the back and tape one edge down using a wooden block for a spacer. Then do the other side. Make the tape snug so it squashes the silicone and leave the mirror alone for 24 hours. After that take the tape and blocks off and you are good to go. Hope this helps.

Jan 07, 2010 | 2002 Subaru Outback

1 Answer

How do i change the bulb in the mirrow for the turn signal in the mirror.

On that model you will find that there is in fact NO bulbs fitted for the turn signal in the mirror. It is 3 small L.E.Ds which are fitted in a clear strip on the bottom of the mirror. To fit this strip the mirror must be disassembled as this strip is held in place with internal screws. The upper trim of the mirror flicks off first and this will allow you to remove these screws.Its a tricky job... Be careful with the mirror glass. Breaks very easily.
Good Luck with it

Aug 15, 2009 | 2007 Volkswagen Passat Sedan

2 Answers

I broke my passanger side mirror. I bought new


Jul 15, 2009 | 2008 Hyundai Elantra

1 Answer

2003 GMC sierra side view mirror glass replacement

That dependso on if the housing itself is broken then yes. If the face plate that is attached to the mirror itself is flapping around then maybe. If it is just the mirror, just go to your neighborhood auto glass shop and but a "Ready-Cut" mirror for a small amount of money. they come already cut to fit perfectly. As for removing the old glass, take a very small flat screw driver and pry the glass away from the face plate. Once completely cleaned out use the adhesive from the ready cut and place them on the face plate. Next press the new mirror onto the flace pate, being careful not to press to hard or it will snap it in half.

Jun 03, 2009 | 2003 GMC Sierra 1500

1 Answer

How do I fit a drivers door glass mirror to a Mercedes SL320?

There is a good set of instructions at Do a search for outside mirror replacement and i think you'll find all you need to get this accomplished.

Mar 28, 2009 | 1998 Mercedes-Benz SL-Class

2 Answers

How do i remove and replace the driver's side mirror?

If the metal pivot arm is not broken you can just replace the glass and plastic housing. To remove the glass you tilt the glass down towards the floor and use a wide plastic or wood bladed object to prise from behind, the glass should pop off from its clips. Remember to catch it if its not damaged. To remove the housing once the glass is out you need to look underneath the mirror unit, there you will find a small plastic bung, gently prise it out and then use a long small flat bladed screwdriver straight up inside the hole and lever towards the front of the car whilst lifting straight up on the plastic housing, this should then lift off. To replace just slot the new housing on and click into place then fit the glass back, remember to connect the wires first if it is a heated glass.
If the metal pivot arm is broken then you will find the remaining screws behind the plastic trim inside the vehicle.

Oct 26, 2008 | 1998 Volkswagen Beetle

Not finding what you are looking for?
2003 Kia Sedona Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

80531 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides