Question about 1999 Nissan Quest

1 Answer

Replacing ignition distributor on 99 mecury villager and have found top dead on cilander #1 where does the rotor point

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Well before you took the old distributor off take notice of rotor button location.If you already removed the old distributor locate number one cylinder and point rotor button to that cylinder. it might have to be done a couple of times to get it just right.

Posted on Jul 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the pick-up coil from the distributor. 1989 GMC 1500 4X4


The distributor does have to be removed and dis-assembled in order to replace the ignition pick-up coil/stator, and if the pick-up coil/stator is faulty then the distributor should be replaced because the distributor will come with a new pick-up coil/stator and the old distributor will have to be removed anyway and in the long run it will actually save money from not having to pay a mechanic to remove and dis-assemble the distributor to replace the pick-up coil/stator, however most of the time it is the ignition module inside of the distributor that is faulty.




When the engine is at TDC (Top Dead Center) is the ignition rotor pointing to the #1 position on the distributor housing as described below?



The engine should be set on TDC (Top Dead Center) with the distributor cap removed, and there is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. (Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing)

This static timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.



If the engine is at TDC and the ignition rotor does not point to the #1 mark on the distributor housing, then loosen the hold down bolt to the distributor and turn the distributor until the rotor is pointing to the #1 mark on the distributor and then tighten the distributor hold down bolt.


6_24_2012_9_32_16_pm.jpg

Jun 24, 2012 | GMC K1500 Cars & Trucks

1 Answer

Blown head gasket, replaced and now cant time. all books and web say that the vehical is not timeable it has to be done by a comp. tech 2. but we went to dealer and their tech 2 couldn't read it. i cant...


The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.

There is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. This "static" timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.

1. Place the engine at top dead center.

2. Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing indicating the number one position.

3. With the engine on top dead center the ignition rotor should be pointing to the number one mark or notch that is on the distributor housing, if it is not then loosen up the distributor and turn the distributor until the ignition rotor is pointing to the mark or notch on the distributor housing and then tighten down the distributor, the engine should now be static timed.

If the distributor can not be turned enough to align the ignition rotor with the number one mark on the distributor housing, or the distributor does not set properly and will not allow the installation of the spark plug wires then the distributor is not installed correctly and is most likely a tooth off and it will need to be re-installed correctly. (The distributor should set like it is shown in the firing order diagram when it is properly installed)


Let me know if you require a firing order diagram or any further assistance.

Sep 23, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

What is the timing specs for a chevy 98 suburban V8 350 gas.


The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these proceedures.

There is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. This "static" timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.

1. Place the engine at top dead center.

2. Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing indicating the number one position.

3. With the engine on top dead center the ignition rotor should be pointing to the number one mark or notch that is on the distributor housing, if it is not then loosen up the distributor and turn the distributor until the ignition rotor is pointing to the mark or notch on the distributor housing and then tighten down the distributor, the engine should now be static timed.

If the distributor can not be turned enough to align the ignition rotor with the number one mark on the distributor housing, or the distributor does not set properly and will not allow the installation of the spark plug wires then the distributor is not installed correctly and is most likely a tooth off and it will need to be re-installed correctly. (The distributor should set like it is shown in the firing order diagram when it is properly installed)

Here is a firing order diagram to also help assist you.


45b5651.jpg

Aug 05, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

1999 silverado 4.3 cranks but no start can hear fuel pump, swaped out coil and crank sensor w/ known good parts no change, engine did start once after coil was changed ran rough and stalled and wont...


First check to see if full battery voltage is even getting to the "Pos" (+) positive side of the ignition coil when the key is in the "Run" position, and also that full battery voltage is getting through the "Pos" (+) or positive side of the ignition coil and over to the distributor ignition module

The ignition module and the pick-up coil/stator located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil, and a faulty ignition module can cause any one of these systems to malfunction.

That does sound like a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores. If the ignition module does test out alright then the problem could still be in the pick-up coil/stator, (it can be tested using an ohm meter by dis-connecting the wire connector from the pick-up coil/stator and the ohm reading between the two wires from the pick-up coil/stator should be between 500 and 1500 ohm's, and both of the wires from the pick-up coil/stator should show an open loop or an infinite reading between each wire and ground) and if the pick-up coil/stator is found to be faulty then replace the entire distributor, or the distributor will have to be dis-assembled to install a new pick-up coil/stator.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

To replace the distributor follow this procedure;

The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.

There is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. This "static" timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.

Removal;

1. With the engine at top dead center.

2. Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing indicating the number one position.

3. With the engine on top dead center the ignition rotor should be pointing to the number one mark or notch that is on the distributor housing, Then make a reference mark of the position that the ignition rotor is pointing to (out on the engine or firewall) and the more precise you mark the position, the easier the installation of the new distributor will be. This will be reference mark #1.

4. Remove the distributor lock down bolt, (the lock down clamp will most likely be attached to the distributor and if so it should not be removed from the distributor) then slowly lift up on the distributor about three inches and note the direction that the ignition rotor turns, and when the ignition rotor stops turning then mark the position that the ignition rotor is pointing to (out on the engine or firewall) and then lift the distributor striaght up and out, and remove the gasket or any left over gasket material from the intake manifold. The more precise you mark the position the easier it will be to install the new distributor and an assistant might be helpful. This will be reference mark #2

Once the distributor has been removed it is important that the engine does not get cranked over by the starter or the crankshaft turned at all, or the reference marks will become useless.

Installation;

Be sure that the new distributor is complete with a new module and that there is a new gasket in place on the distributor.

1. Lower the distributor with gasket down into the distrbutor well and align the ignition rotor with the #2 reference mark and when the distributor gear engages the drive gear on the camshaft then the ignition rotor should turn to the #1 reference mark as the distributor sets all the way back down flush on the intake manifold.

2. Install and tighten the lock down bolt, and If the distributor is properly installed then the ignition rotor should be pointing to the #1 reference mark and the #1 position on the distributor housing with the engine on top dead center.

Replace the distributor cap and connect the spark plug wires, and see if the engine will start, if the engine does start and the check engine light does not come on (assuming that it was not on before) then the distributor is properly installed and there is no further timing requirements.

Let me know if you require any further assistance.



a4e111e.jpg

71a37c7.jpg

91bcf9e.jpg

Jul 31, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Installed new crate engine 1997 5.7 vortec, how do you adjust the timing? 1997 GMC Serria 4x4 1500


The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these proceedures.

There is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. This "static" timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.

1. Place the engine at top dead center.

2. Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing indicating the number one position.

3. With the engine on top dead center the ignition rotor should be pointing to the number one mark or notch that is on the distributor housing, if it is not then loosen up the distributor and turn the distributor until the ignition rotor is pointing to the mark or notch on the distributor housing and then tighten down the distributor, the engine should now be static timed.

If the distributor can not be turned enough to align the ignition rotor with the number one mark on the distributor housing, or the distributor does not set properly and will not allow the installation of the spark plug wires then the distributor is not installed correctly and is most likely a tooth off and it will need to be re-installed correctly. (The distributor should set like it is shown in the firing order diagram when it is properly installed)

Here is a firing order diagram to also help assist you.


445ea9b.jpg

Jul 06, 2010 | 1997 GMC Sierra K2500

2 Answers

How to remove distributor on a 1998 gmc pick up with 5.0 engine, do I have to mark anything or just take off bolt and pull out.


You need to mark in 2 places. With the cap off mark the position of the rotor button on the distributor housing first. Then you need to make a mark on the distributor housing that will line up with a mark on the engine itself.
When you put the distributor back in back the rotor button up before you put it in because the cam gear will turn it ahead as it seats. For example, if the rotor button is at 3 o'clock then back it up to 1 o;clock.
Don't force the distributor down at the end because you can damage the end that drives the oil pump. Fidle and wiggle it as you push and it should line up and drop onto the oil pump. Also DON'T turn the engine over while it's out or you will have to retime the engine. Hope this helps.

Jul 03, 2010 | 1998 GMC Sierra

1 Answer

Cam/Crank Sensor correlation problem


Thr problem should be the static timing for the distributor, and this is how it should be set;

There is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. This static timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.

1. Place the engine at top dead center.

2. Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing.

3. With the engine on top dead center the ignition rotor should be pointing to the mark or notch that is on the distributor housing, if it is not then loosen up the distributor and turn the distributor until the ignition rotor is pointing to the mark or notch on the distributor housing, the engine should now be static timed.

Jun 12, 2010 | 1999 Chevrolet C2500

2 Answers

How do you set the timing on a 1998 GMC Sierra?


The timing is not adjustable and it is computer controlled, but the distributor must still be clocked in properly and static timed, and here is how it is done.

There is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. This static timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.

1. Place the engine at top dead center.

2. Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing.

3. With the engine on top dead center the ignition rotor should be pointing to the mark or notch that is on the distributor housing, if it is not then loosen up the distributor and turn the distributor until the ignition rotor is pointing to the mark or notch on the distributor housing, the engine should now be static timed.

Jun 12, 2010 | 1998 GMC Sierra

1 Answer

Setting the distributor in a v 8 vortech engine


the first cylinder on top dead center put the distributor rotor should be positioned first cylinder.

Oct 14, 2008 | 1998 Chevrolet C3500

Not finding what you are looking for?
1999 Nissan Quest Logo

Related Topics:

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...