Question about 1991 Ford Econoline

1 Answer

No power to the hole van - 1991 Ford Econoline

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 424 Answers

Check battery connection and fusible link at the starter solenoid. I would start there. Good luck.

Posted on Jul 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windstar problem


Sounds like a blown head gasket and one of the cylinders is full of coolant. Try removing the spark plugs and see it it will crank.

Feb 06, 2014 | Cars & Trucks

1 Answer

Nissan quest sunroof drain clogged


open your skylight and feel in the front corners for muck stuck infront of the drainage holes. Use a pipe cleaner or other wire to poke through the holes and the water should drain out. It is a little difficult to see the holes but just feel around.

Apr 18, 2013 | 2004 Nissan Quest

1 Answer

Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




  1. Remove the wire clip.
  1. Disconnect the power outside rear view mirror electrical connector.




  1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal
  1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws.


    Remove the outside rear view mirror mounting hole cover.
Installation
To install, reverse the removal procedure. Mirror Control
Removal
  1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


May 13, 2010 | 1995 Mercury Villager

1 Answer

Where is oil fill plug on mitsubishi express van manual trans??


fuel filer will be located blow ur chasy near fuel pump, generally.

n about Oil fill hole, it will located next to the engine, below the hood, or above the gearbox, for manual transmission. thank u

Jul 17, 2009 | 1990 Mitsubishi Minivan

1 Answer

Hole in front bumper of Infiniti I30 2001


Sure. Use bondo. Do you have a paint sprayer?

Most composite bumpers have the paint in the composite, but I dont' know why, at least for a coupe or three years, the bumper wouldn't hold paint sprayed on.

May 05, 2009 | Hyundai Motor 2004 Sonata

2 Answers

2001 Chvy van: overheat+water leak/from strange(new?) hole


seems u have a blown head gasket or cracked head!

Mar 18, 2009 | 2001 Chevrolet Astro

2 Answers

My escort van is out of timing need to set timing again


YOU NEED TWO 6MM DRILL BITS, THERE ARE TWO HOLES TO PUT THESE IN, ONE ON THE CAMSHAFT AND THE SECOND ON THE PUMP. SLOWLY TURN THE ENGINE BY HAND UNTIL THE TWO HOLES LINE UP WITH HOLES BEHIND THEM, THEN PLUG WITH THE DRILL BITS. ITS NOW SAFE TO REMOVE THE BELT BY TAKING OFF THE TENSIONER AND LOCKING OFF. PUT ON THE NEW BELT AND RELEASE THE TENSIONER SLOWLY AND REMOVE THE DRILL BITS. TURN THE ENGINE BY THE NUT ON THE CRANK SHAFT A COUPLE OF TIMES. THEN PULL BACK THE TENSIONER ALL THE WAY, THEN LET IT GO SO IT SNAPS AGAINST THE BELT, IT IS NOW TENSIONED AND JOB DONE

Feb 28, 2009 | 1999 Ford Escort

Not finding what you are looking for?
1991 Ford Econoline Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...