Location of oil pressure sensor on 2003 kia rio 4 cylinder manual.

Need to remove the oil pressure sensor and install a mechanical gauge to read actual pressure. If the pressure is ok you have a bad sensor or a wiring issue

replaced crank and cam sensor [Archive] - Sorento Nation - KIA ...

www.sorentonation.com/forum/archive/index.php/t-913.html

20 posts - ‎6 authors
replaced crank and cam sensors put back together cranked up very rough idle some tapping any ... 12-17-2012, 12:24 AM ... It's a 2006 3.5 Kia Sorrento. ... I found theproblem the SUV has a aftermarket alarm and remote start system I tripped ...

Kia Rio Crankshaft Position Sensor Replacement - YouTube

? 4:44
https://www.youtube.com/watch?v=hihQxMWuSFY
Mar 21, 2014 - Uploaded by Jason Roush
While looking for how to replace a Kia Rio crankshaft positionsensor, ... is on and i have a P0340 code, think this is theproblem? kia rio 2002.

Kia Sorrento/Sedona: 3.5 Litre Engine/Timing Belt/Crank ...

? 20:23
https://www.youtube.com/watch?v=CjaD_zYPrUA
Mar 29, 2014 - Uploaded by JamieJones TheCarMan
Repair and/or Replacement tips for timing belt, crank sensor,cam sensor, water pump and drivebelt ...

Crankshaft position sensor - 2003 Kia Sorento - RepairPal

repairpal.com > Questions > Kia > Sorento > 2003 Kia Sorento

The cam sensor on a 2003 Kia Rio is located on the front, driver's side of the engine, Should be the same on the 2004 ki8a reo's. God-Bless! This is for the 1.6,

On 2003 Kia Rio the knock sensor is located under the intake manifold and must be changed from underneath the car. If you remove the oil filter it is directly above it and is in clear view once the oil filter is out of the way. The connector plugs in behind the intake manifold air breather on the top side. If you remove the air breather cover it will help you get to it. It's not Complicated it's Just a process Of Changing the Knock Sensor.

HERE'S A LINK ON HOW TO REPLACE YOUR KNOCK SENSOR. http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?fromSearchPage=true&pageId=0996b43f803762d2&partName=Knock+Sensor++KS&partId=0996b43f803762d2 HERE'S WHAT THE KNOCK SENSOR LOOK'S LIKE. http://www.autozone.com/engine-management/knock-sensor/duralast-knock-sensor/kia/rio/2004/4-cylinders-5-1-6l-mfi-dohc/363953_0_0

you want to know what kind of oil to put in its 5w30

My 2003 Kia Rio has almost 200,000 miles on it... 4 months ago I drove it over 2,000 miles with no problems. Before leaving, I took it in to my mechanic to have them change the oil and oil filter, and just generally check it over... fluid levels, brakes, tires ~ basic stuff.
Good luck!

Turn ignition off. Disconnect knock sensor 3
-
pin harness connector. Locate knock sensor, on cyli
nder block.
On Optima 2.7L engine, sensors are located on both
sides of cylinder block. . Remove knock
sensor from cylinder block. To install, reverse rem
oval procedure.

knock sensors thread into the head cylinder or intake manifold

2003 kia rio, It is located under the intake manifold. Get underneath the car, pull the oil filter...it is right above it and in clear view with the oil filter out of the way. The connector plug is up top behing the air breather on the firewall.