Question about 2000 Chevrolet S-10

1 Answer

My 4wd hi isnt engaging on my 2000 chevy s10. 4Lo works perfectly but when i hit the 4hi button the light blinks but nothing happens with the transfer case. any suggestions?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 65 Answers

Defective switch likely

Posted on Jul 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chevy suburban stuck in 4 lo anyone out that cant help


Put truck in Neutral while key in run position engine off or on (doesn't matter which). If it's pushbutton 4wd then try hitting 4low again. if that doesn't work some of the chevy trucks required you to press 4hi to get into 4high and then press 4hi again to get back to 2hi, unless yours has a 2hi button. In that case press 4hi to get into 4high and then press 2hi to get back to 2wd. either way you need to be in neutral to get out of 4lo. I have shift on the fly (Mechanical Shifter on floorboard for transfer case) on my 1990 Suburban and still have to put it in neutral to get out of 4lo. Good Luck.

Jan 30, 2014 | 2000 Chevrolet Blazer

1 Answer

My 1997 GMC Sierra lights for 4hi and 4lo blink when i push the 4hi button and then goes back into 2hi. but when i push 4lo it locks in and works fine. I tried changing the 4wd motor on the transfer c


THE TRANSFER CASE MOTOR IS ONLY FOR 4WD LOW. That would have never been the problem as soon as you confirmed it shifted into 4wd Low. 2wd and 4 Hi work off of vacuum. You may have one or two issues. A vacuum leak up by the front axle that engages the 4wd HI or the sensors on the transfer case.

Nov 22, 2013 | 1997 GMC Sierra

1 Answer

Chevy trailblazer 4wd is not engaging 4hi blinking and service 4wd light is on


There are two actuators that activate the 4WD components, one is for the Transfer case modes and the other is for the front axle disconnect. Both of these actuators make a distinctive noise (motor noise) when activated. First thing to do is with engine off and ignition on, switch from 2HI to 4HI and listen for two distinctive noises. If you hear both, more than likely the front spline disconnect assembly (at the front axle) is defective.
In order to troubleshoot the 4WD system, you need to have an understanding of the whole thing, it is not a DIY item.

Feb 21, 2013 | 2002 Chevrolet TrailBlazer

1 Answer

2001 Chevy 4WD button lights don't come on - 4WD wont engage


check the solenoid on the front chunk these vehicles have had a lot of problems with these solenoids. have personally replaced about 10 of these on 98-02 models.

Aug 26, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

Chevrolet truck 4wd switch blinks


If they are blinking I believe it means that there are fault codes present in the pcm. You need to get the computer scaned to see if there are an codes present. If you live near an Autozone or Checker autoparts they can scan it for free.

Jun 21, 2009 | 1996 Chevrolet K1500

1 Answer

97 chevy k1500 wil not shift into 4 high, just 4 lo and 2 hi


The motor that drives the transfer case is not working it has to be replaced.

Nov 03, 2017 | Chevrolet Cars & Trucks

1 Answer

98 K1500 suburban, can not engage 4wd, HI or Lo runs otherwise


your doing it right but your accuater is bad 59.00 auto zone easy install

Feb 23, 2009 | 1998 Chevrolet Suburban

1 Answer

On my 2000 chevy S10 blazer, when I push the 4HI button, the 4HI and 4LO buttons flash a yellow light and it won't shift to 4WD, stays in 2HI and the light in the 2HI button is on yellow......I hear...


vacuum leak or vacuum locker solenoid problem. a great way to check for both is to remove both vacuum lines from the solenoid (located on firewall above destributor), and put a connector between them, push the button on the dash and see if it locks in.

Jan 18, 2009 | 1999 GMC Jimmy

1 Answer

My 98 chevy blazer won't shift into 4wd.


Most common problem is the vacuum diaphragm that is so inconviently mounted UNDER the battery tray.The cable that locks in the front diff is attached to it and vacuum pulls it in/out.

Dec 22, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2000 Chevrolet S-10 Logo

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...