Question about Chrysler 300M

1 Answer

Remove starter from chrysler 300m

We removed the bolts from the starter, but still can't get it off. How do we remove and replace it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,071 Answers

There is a bracket bolted to the end of starter to block

Posted on Jul 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a video on how to change the ac belt on a 2003 chrysler 300m


You should not need a video. Just loosen the center bolt on each tensioner the there is a bolt under each tensioner that needs to be loosen to remove the belts.

Jul 14, 2014 | 2003 Chrysler 300M

1 Answer

How u replace starter 2000 chrysler 300m


Support engine and remove motor mount to reach starter.

Mar 07, 2012 | 2000 Chrysler 300M

2 Answers

Could you please tell me how to replace the air conditioner belt on a 2002 Chrysler 300M


  • On the lower front passenger side of the engine there is an adjustable idler pulley for the AC. Loosen that center bolt a few turns to release the tension on the AC belt.
  • Remove the old belt.
  • Place new belt on.
  • Tighten the idler pulley bolt until the belt is snug.
  • Job complete.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jun 14, 2011 | 2002 Chrysler 300M

1 Answer

How to replace the a/c belt on a 2001 chrysler 300M


you need to remove upper radiator core support set on engine loosen 15mm bolt on front of alternator tensioner and 13mm bolt behind the tensioner pulley remove this belt then go under passenger front and you will see the tensioner bolt for the ac belt turn until tension is released remove belt replace belt and reverse instructions to put back together

May 24, 2010 | 2001 Chrysler 300M

1 Answer

Need to replace a idle air control valve on a 1999 300M Chrysler


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the IAC electrical connector.
  3. Remove the IAC mounting screws.
  4. Remove the IAC.



da3669e.gif

To install:
  1. Install the IAC to the throttle body.
  2. Tighten mounting screws to 5.1 Nm (45 inch lbs.) torque.
  3. Attach electrical connector to the IAC.
  4. Connect the negative battery cable.
  1. Disconnect electrical connector from IAC motor.
  2. Disconnect air plenum (where applicable).
  3. Remove two mounting bolts (screws).
  4. Remove IAC motor from throttle body.

3ccd55e.gif

To install:
  1. Install IAC motor to throttle body.
  2. Install and tighten two mounting bolts (screws) to 60 inch lbs. (7 Nm) torque.
  3. Install electrical connector.
  4. Connect air plenum (where applicable).

Mar 06, 2010 | 1999 Chrysler 300M

1 Answer

Need to find starter on 2000 chrysler 300m


The starter is under the car on the left side by the oil filter. You will need to take off the oil filter, the motor mounts, and then take the starter off, their are 3-4 bolts holding the starter on, the hardest one to get off is the one on the top . You will need a swivel to get the top one off. It will take about 3 hrs or so as long as they give you a good starter at the store.

Jul 02, 2009 | 1999 Chrysler 300M

1 Answer

I need to know where the location of the thermostat is on a 1999 chrysler 300m so i can replace


The 2.7L engine lower radiator hose, connects to the thermostat housing.

To Remove:
1.Disconnect the Negative battery cable.
(Engine COLD!)
  1. Drain cooling system.
  2. Remove radiator lower hose from thermostat housing.
  3. Remove nuts from heater tube flange studs.
  4. Loosen starter bolt at heater tube bracket.
  5. Pull heater tube out of thermostat housing and position out of the way.
  6. Remove bolt and two studs.
  7. Remove thermostat housing, O-ring and thermostat.
  8. Remove thermostat housing bolts.
To install:
A.Clean gasket sealing surfaces.
B.Install thermostat with the bleed valve located at the 12 o'clock position, between tabs on seal.
  1. Install thermostat and seal into thermostat housing .
  2. If removed, install two studs.
  3. Install thermostat, thermostat housing and O-ring and bolt. Tighten attaching bolts to 105 inch lbs.(12 Nm).
  4. Lubricate new heater return tube O-ring with coolant.
  5. Position heater return tube flange over two studs. Install nuts.
  6. Tighten retaining nuts to 53 inch lbs.(6 Nm).
  7. Tighten starter bolt to 40 ft. lbs. (54.3 Nm).
  8. Connect the lower radiator hose to the thermostat housing. Install hose clamps.
  9. Refill cooling system.
  10. Inspect for leaks.
  11. Connect negative cable.
3.2 and 3.5L engines:
Disconnect the battery cable. (Again engine COLD)
  1. Drain cooling system.
  2. Raise vehicle on hoist.
  3. Disconnect electrical connectors from engine oil and power steering pressure switches.
  4. Disconnect radiator and heater hoses from thermostat housing.
  5. Remove thermostat housing bolts.
  6. Remove housing, thermostat, and gasket.
The OEM thermostat is staked in place at the factory. To ensure proper seating of replacement thermostat, carefully remove the bulged metal from the thermostat housing, using a suitable hand held grinder. It is not necessary to restake the replacement thermostat, into the thermostat housing.

To Install:
  1. Position gasket on thermostat and housing.
  2. Install thermostat housing, gasket and mounting bolts onto block. Tighten attaching bolts to 105 inch lbs. (12 Nm).
  3. Install radiator hose.
  4. Install bypass hose.
  5. Connect electrical connectors from engine oil and power steering pressure switches.
  6. Connect negative cable.
  7. Fill cooling system.
  8. Inspect for leaks.
  9. Lower vehicle on hoist.
From AutoZone Repair Guides

I feel this way, I can give you an accurate description, and have taken into account your safety.

May 12, 2009 | 1999 Chrysler 300M

1 Answer

Inner cv hub removal chrysler 300m


I hate to ask but, the 3 retaining bolts are out right.? Should be able to pry with 2 bars side to side etc. Not working that way?

Apr 27, 2009 | 2003 Chrysler 300M

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

944 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...