Question about 1996 Ford F350 Crew Cab

1 Answer

My 20001 f350 2 wheel drive front tires lean in at

My 2001 f350 2 wheel drive front tires lean in at the top i have replaced all the bushings and ball joints and wheel bearings....What elsr could it be

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 64 Answers

On the 01 there is a camber bushing that goes in the knuckle with the upper ball joint( the factory ones wear out), take it to a alignment shop, specify you want the camber set, and they will be able to provide a shim and install it for you,it only take a couple secs to install, you can turn the aftermarket shim to achieve correct camber.

Posted on Jul 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford e150 pulling to left, also when backing up it goes left without turning the wheel.


wheel bearing failure allows wheels to lean it that top
next is ball joint failure followed by suspension bush failure
Take it to an accredited suspension shop and when finished with the repairs have a wheel alignment done

May 08, 2017 | 2003 Ford E150

1 Answer

What is causing my right front tire to lean inwards at the top


Usually if the tire is leaning noticeably, it's a bad ball joint or radial arm bushing.

Jan 18, 2016 | 1996 Ford F150 Regular Cab

2 Answers

Shaking wheels on my 2001 E150


There should be problems on the balljoint or it might the tie rod worn out..

Aug 06, 2013 | Cars & Trucks

1 Answer

Front passenger wheel leaning on 98 expedition


This is most likely a ball joint problem. If you can, jack that tire up in the air and see if you can move the whole tire in and out from the top. Try to see if there is movement in the ball joints while you move the tire. If that is not the problem, it could be a wheel bearing, but i would check the ball joints first. Hope this helps.

Feb 23, 2013 | 1998 Ford Expedition

1 Answer

2001 durango right front tire leans out on top why


ball joints or wheel bearings are bad get this fixed before driving very far

Oct 13, 2012 | 2001 Dodge Durango

1 Answer

Car sways and leans


possibly worn out shock absorbers. however could be top strut mounts , lower ball joint bushes, rear axle bushes , subframe bushes best to get it checked out at your local garage

Apr 29, 2012 | 1999 Isuzu Rodeo

1 Answer

Front tires are leanin in


After double checking the design, it makes no difference if your truck is 2 or 4 wheel drive. There is an eccentric bushing located between the upper ball joint and the top section of the front axle. You can adjust the camber [inward to outward tilt] of each wheel by removing the upper ball joint from the axle and rotating that bushing. Make sure there is no play in either of the ball joints on each wheel. Replace any worn ball joint, before adjusting the eccentric bushing. The link below shows what an eccentric bushing looks like, although the linked item is not specifically for your truck. See

http://automotivetoolsusa.com/moog-k8979-caster-camber-bushing

If you can not adjust the camber [tilt] to be within specifications, you will need special equipment to heat and bend the front axle to achieve proper camber. This sort of thing is best done by a truck alignment shop.

Nov 24, 2011 | 1989 Ford F 150

2 Answers

My honda has been shredding my tires on the front axle. I thought it was a alignment i needed, but now its making a horrible noise on the left front side of my car, and it feels like the tire wants to fall...


You may have an issue with a ball joint or "A" arm bushing - I recommend you stop driving it and have it towed to your local auto shop for a hands on diagnostic. If the ball joint breaks you could possibly lose your entire wheel assembly while moving- this happened to my wife's van 2 months ago and was an expensive fix. If a bushing goes on the "A" arm then your wheel will lean and that will shred the tire too and may ruin the arm requiring replacement. Either way you would be safer to get it towed right away!!

Nov 26, 2010 | 2000 Honda Accord

3 Answers

I just got my hands on a 95 Pathfinder. The front tires have a lot of wear on the inside edges. I was told by seller that this is caused by driving on pavement in 4WD. As this is my first 4x4, I wasn't...


I'm guessing the lower ball joints are shot. This will cause the tires to lean in on the top and and wear the inside of the tire. I could be wrong! Try jacking the front wheels up and support the vehicle on jack stands, now grab the tire top and bottom and try to rock it in and out. If there is movement, you will have to have someone watch to see what is moving, while you rock it. If it's the ball joints, they will need to be replaced before you can align it. This can be spendy, there's a lot of labor involved.

Mar 27, 2010 | 1995 Nissan Pathfinder

1 Answer

Front tire on pasingers side is waring on the out side and yet it will not pull eather way whenyou let go of the wheel, the drivers side is not wearing at all ,ondly the pasingers side


There is excessive camber in the front suspension, causing the wheel to lean too much to the inside or outside and putting too much load on one side of the tire. The car may simply need the wheels aligned, but misalignment could be due to sagging springs, worn ball joints, or worn control arm bushings. Because load has a great affect on alignment, be sure the car is loaded the way it's normally driven when you have the wheels aligned

Jul 07, 2009 | 2001 Chevrolet Astro

Not finding what you are looking for?
1996 Ford F350 Crew Cab Logo

363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...