Question about 2006 Dodge Caravan

1 Answer

Do you have to pull the motor to remove the crank?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Yes it has to be pulled

Posted on Jul 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

208cc motor is knocking and the connecting rod and piston seem to be fine


So you have raised a problem with a car or truck, and its engine has pull cord?

Dec 21, 2013 | Cars & Trucks

1 Answer

Crank shaft


You must remove the engine from the car and then pull it apart to replace the crank, this is a very time intensive job that requires lots of skill and special tools, it is not for the home mech.

Oct 08, 2012 | 1998 Dodge Intrepid

1 Answer

Can i replace the rear crank seal without removing the motor?


Afraid not.
Its a one piece seal that wraps around the crank.
You'll have to pull the motor or the transaxle to get access to the flywheel.

Aug 16, 2012 | 1996 Chevrolet Monte Carlo

1 Answer

Engine schematics 2002 pontiac montana


Hi there:
Isnt a diagram but If you have removed the motor, here is the motor installation procedure....

INSTALLATION PROCEDURE

6_23_2012_11_48_33_pm.gif

Align the wiper motor to the wiper drive system module. NOTE: Refer to Fastener Notice in Service Precautions.
Install the wiper drive system module to wiper motor screws. Tighten Tighten the wiper drive system module to wiper motor screws to 7 N.m (62 lb in) .
Connect the electrical connector to the wiper motor.
Install the crank arm on the wiper motor.


6_23_2012_11_49_39_pm.gif

Rotate the washer solvent container into the installation position.
Install the washer solvent container screws. Tighten Tighten the washer solvent container screws to 6 N.m (53 lb in) .
Inspect the wipers for proper operation.


6_23_2012_11_51_04_pm.gif

Also, here is the crank arm procedure...

REMOVAL PROCEDURE

Remove the wiper system module cover.
Remove the drive link from the wiper motor crank arm.

2.1. Loosen the drive link screws.
2.2. Remove the drive link from the wiper motor crank arm.

Remove the wiper motor crank arm cover and seal.
Remove the wiper motor crank arm from the wiper motor.

4.1. Loosen the wiper motor crank arm screw.
4.2. Tap on the wiper motor crank arm screw with a soft-faced mallet while holding up on the wiper motor crank arm until the wiper motor crank arm loosens from the wiper motor.
4.3. Remove the wiper motor crank arm screw and the wiper motor crank arm from the wiper motor.

INSTALLATION PROCEDURE


6_23_2012_11_52_10_pm.gif

Install the wiper motor crank arm onto the wiper motor.

1.1. Turn the ignition switch to the ACCY position.
1.2. Set the wiper switch to PULSE position. The wiper motor should be operating.
1.3. Turn the ignition switch to OFF when the wiper motor is in the innerwipe position.

IMPORTANT: Do not rotate the wiper motor shaft during the installation of the wiper motor crank arm.

1.4. Install the wiper motor crank arm on the wiper motor while maintaining a 4-8 mm (0.157-0.315 in) gap between the V-grove in the wiper motor crank arm and the tab.

NOTE: Refer to Fastener Notice in Service Precautions.

Install the wiper motor crank arm screw. Tighten Tighten the wiper motor crank arm screw to 16 N.m (12 lb ft) .
Install the wiper motor crank arm cover and seal.


6_23_2012_11_52_52_pm.gif

Check the gap between the wiper motor crank arm and tab. If the gap is not 4-8 mm (0.157-0.315 in) , remove the wiper motor crank arm and repeat installation steps.
Install the drive link onto the wiper motor crank arm.
Install the drive link screws. Tighten Tighten the drive link screws to 5 N.m (44 lb in) .
Install the wiper system module cover.
Inspect the wipers for proper operation.

Additional procedures: Wiper Motor Module Replacement.

TOOLS REQUIRED
J 39822 Wiper Arm Puller

REMOVAL PROCEDURE

Turn the ignition switch to the ACCY position.
Set wiper switch to the PULSE position.
Turn the ignition off when the wiper arms are in the innerwipe position and not moving.
Disconnect the washer hose from the washer nozzle.
Remove the cover from the wiper arm nut.
Remove the wiper arm nut from the wiper transmission drive shaft.
Using J 39822 remove the wiper arm from the wiper transmission.
Remove the wiper blade from the wiper arm.
Clean the knurls of the wiper transmission drive shaft with a wire brush.



Install the wiper blade onto the wiper arm.
Install the wiper arm onto the wiper transmission drive shaft. IMPORTANT: Hold the measuring device at 90 degrees (perpendicular) to the wiper blade tip.
Measure the distance from the wiper blade tip to the solid edge of the windshield blackout. Position the wiper arms at the following distances:

LH - 147 mm (5.79 in) above the glass blackout.
RH - 123 mm (4.84 in) below the glass blackout.

NOTE: Refer to Fastener Notice in Service Precautions.



Install the wiper arm nut onto the wiper transmission drive shaft. Tighten Tighten the wiper arm nut to 48 N.m (35 lb ft) .
Install the cover on the wiper arm nut. IMPORTANT: Lubricate the washer hose with the windshield washer solvent to ease installation on the washer nozzle.
Install the washer hose on the washer nozzle.
Inspect the wipers for proper operation.



Remove the wiper arms from the vehicle.
Remove the air inlet grille panel.
Remove the wiper motor.
Remove the air inlet panel to wiper motor module screws.
Remove the wiper motor module from the vehicle.
Remove the insulators from the wiper motor module.

INSTALLATION PROCEDURE

Install the insulators onto the wiper motor module.
Align the wiper motor module to the air inlet panel. NOTE: Refer to Fastener Notice in Service Precautions.
Install the air inlet panel to wiper motor module screws. Tighten Tighten the air inlet panel to wiper motor module screws to 10 N.m (89 lb in) .
Install the wiper motor.
Install the air inlet grille panel.
Install the wiper arms onto the vehicle.
Inspect the wipers for proper operation.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 2002 Pontiac Montana

1 Answer

Can the pistons be removed from my 1964 3.4 jaguar without taking the engine out


yes, drop the oil pan to expose the crank and pull off the heads to expose the top of the pistons but if you have to do any work on the crank, you are probably going to have to pull the motor out

Mar 25, 2011 | Jaguar S-Type Cars & Trucks

1 Answer

I'm looking for instructions on how to replace the window wiper motor and switch


Windshield Wiper Motor Removal & Installation To Remove:
Using the J 39232, remove the wiper transmission from the wiper motor crank arm. gmpc_wa_1.gif

  1. Remove the wiper arms
  2. Remove the air inlet grille panel.
  3. Disconnect the connectors from the wiper motor assembly.
  4. Remove the three screws and the wiper drive system module.
  5. Using GM special tool J 39232 or equivalent, separate the wiper motor crank arm from the wiper drive ball joint.
  6. Remove the wiper motor crank arm from the wiper motor.
    • Remove the rubber boot.
    • Loosen the mounting screw.
    • Tap on the screw with a plastic or leather faced hammer while supporting the wiper motor crank arm.
    • Tap the screw until the crank arm is loose.
    • Remove the screw and crank arm from the motor.
  7. Remove the three screws and separate the wiper motor from the module assembly.
To Install:
  1. Position the wiper motor on the wiper drive system module assembly. Install the three mounting screws. Tighten the screws to 62 in lb (7 Nm).
  2. Install the wiper motor crank arm on the wiper motor.
    • Connect the wiper motor electrical connector.
    • Turn the wiper switch to the accessory position.
    • Turn the wiper switch to the pulse position.
    • Turn the wiper switch off when the wiper motor is in the middle of the wipe cycle.
    • Disconnect the connector from the motor.
    • Maintain a gap of 0.157-0.314 in (4-8 mm) between the wiper motor crank arm and the bracket tab. If the gap is not 0.157-0.314 in (4-8 mm), remove the wiper motor crank arm and repeat installation.
    • Install the mounting screw. Tighten to 142 in lb (16 Nm).
    • Install the rubber boot.
  3. Position the wiper drive system module on the vehicle. Install the three mounting screws. Tighten the screws to 68 in lb (10 Nm).
  4. Using GM special tool J 39232 or equivalent, connect the wiper motor crank arm to the wiper drive ball joint.
  5. Connect the wiper motor assembly electrical connector.
  6. Install the air inlet grille panel.
  7. Install the wiper arms.
  8. Check the windshield wiper operation.
---

Oct 28, 2010 | 1999 Buick Regal

2 Answers

Sunroof motor and cable replacement


The motor is located in the recess above the near side wheel arch and is mounted on a small frame held in place by two 10mm bolts. In order to remove the motor you will need first to extract the sunroof cable that runs though it. What follows sounds complicated but is quite quick and easy. 1) Ease the sun roof back to half open, if the motor is not working just put a 17mm socket on the nut in the centre of the motor and hand crank it open. 2) Between the sliding metal roof and the headlining panel, about 10cm from the leading edge, are 4 pop connectors. Slip a large bladed screw driver between these and separate. 3) Ease the headlining panel forward and pull it up and out through the sunroof aperture. 4) Now close the sun roof, if necessary using the same hand crank method used to open it. 5) On the under side of the sliding roof panel at the rear in the middle you will see the end of the cable tube guide . Mounted at the end there is a metal butterfly mount located with two 8mm bolts. This mount is what actually holds the end of the cable to the sunroof bridge mechanism. Remove these two bolts and withdraw the whole cable forwards, again the hand crank can help here. Take care this cable will be filthy. Check the end for signs of teeth missing - if so replace and clean the motor gear box of metal shavings 6) Returning to motor - disconnect the electrical connector block. 7) To the front of the motor the sunroof cable tube is held in place with a clip. Push the tube end at 90 degrees to the motor body towards the outside skin of the car to un-clip and to disengage it. 8) to the rear of the motor you will see a similar exit cable tube. This time the the tube must be pulled at 90 degrees to the motor towards the car interior and when unclipped this needs to be moved away towards the rear to clear the motor assembly. 9) Once the two 10mm frame mounting bolts are removed the motor can be extracted 10) Check the health of the (replacement) motor gear box by removing the three 8mm bolts holding the steel backing plate in place. The large plastic driven cog can be removed by undoing the 17mm nut on the other side whilst holding the central spindle with a 6mm open spanner to stop it rotating. 11) Clean everything to a shine and re-grease liberally. 12) Reassembly is the reverse of the above remembering to clean the drive cable and re-greasing prior to reinstallation

Apr 14, 2010 | 1993 Mercedes-Benz 190

1 Answer

Rear main seal is leaking bad so I need to pull the motor (k1500 305)should I pull motor and trans together or just the motor. Any tips and shuold I replace anything else since I have the engine out.


you dont have too pull the motor!!
remove the radiator shroud, remove the distributor cap and rotor, take pipes lose from exsaulst manifold, take out motor mount bolts pick the engine up with a hoist, you now have enough room too drop the oil pan!!remove rear main bearing cap, take lower half of seal out of cap, too remove the up half of seal ,i use a small screwdriver too slide it around the crank ,
grease up the new one and it will slide right in!!
in spect the rod and main bearings while you have it apart and think about replacing them they dont cost much about 4.00 each and if you go that far replace the oil pump its not much either under 30.00!!

Mar 05, 2010 | 1988 Chevrolet K1500

2 Answers

Wiper motor does not work on my 1994 dodge intrepid?


REMOVAL & INSTALLATION
(I made images larger at the end of instructions)

See Figures 1, 2 and 3
0900c1528006ad4a.jpgFig. 1: Unbolt the wiper motor from the housing 0900c1528006ad4b.jpgFig. 2: A little maneuvering may be required to pull the motor out 0900c1528006ad4c.jpgFig. 3: Exploded view of the wiper motor and associated components that make up the wiper system
  1. Disconnect the negative battery cable.
  2. Remove the wiper arm and blade assemblies, then disconnect the in-line hose connections. Do not discard the in-line connectors.
  3. Remove the rear hood seal with the cowl top plastic screen. Disconnect the washer hose in-line connectors.
  4. Disconnect the motor wiring harness at the back side of the housing.
  5. Remove the four wiper housing module mounting screws, then remove the housing.
  6. Remove the nut and disconnect the wiper drive linkage from the motor crank.
  7. Remove the three motor mounting screws. Lift the motor and mounting plate out of the housing.
  8. Disconnect the motor harness grommet from the housing.
To install:
  1. Assemblethe linkage to the motor. Make sure that the crank fits over the D sloton the motor shaft. Tighten the mounting nut to 90-106 inch lbs. (11-14Nm). Be sure the motor is still in the park position before assemblingto the linkage; if it is not, temporarily connect the motor to thewiring and operate the switch to park the motor before assembling thelinkage.
  2. Position the wiper motor and install the retaining nuts until snug.
  3. Attach the linkage drive crank to the motor crank arm.
  4. Plug the wiper motor wiring back together.
  5. Install the wiper motor cover.
  6. Install the wiper arms and plastic cowl removed previously.
  7. Connect the negative battery cable and check the wiper motor for proper operation.

0900c1528006ad4a.gif
Copyright © 2002 Delmar, All Rights Reserved.
0900c1528006ad4b.gif
Copyright © 2002 Delmar, All Rights Reserved. 0900c1528006ad4c.gif
Copyright © 2002 Delmar, All Rights Reserved.

Jan 29, 2009 | 1999 Dodge Intrepid

1 Answer

Windshield washer doesn't work. I'm looking for the location of motor


Service and Repair
  1. Turn ignition switch to the ACCY position, then set wiper switch to the "PULSE position.
  2. Turn ignition switch off when wiper arms are at bottom and not moving.
  3. Lift wiper blade assembly up from windshield.
  4. Pull out retaining latch with a screwdriver.
  5. Pull wiper arm assembly off transmission driveshaft.
  6. Disconnect battery ground cable.
  7. Disconnect hose from washer hose.
  8. Remove five air inlet panel retainers.
  9. Push washer hose into firewall.
  10. Remove air inlet panel from vehicle.
  11. Using wiper transmission separator tool No. J-39232, or equivalent, remove transmission drive link socket from wiper motor crank arm.
  12. Pull two harness connector retainers out of wiper motor connector.
  13. Disconnect two harness connectors from wiper motor.
  14. Remove wiper motor attaching bolts and stud, then the wiper motor from the vehicle.
  15. Reverse procedure to install.

Dec 10, 2008 | 1995 Oldsmobile Aurora

Not finding what you are looking for?
2006 Dodge Caravan Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...