Question about 2003 Jeep Liberty

1 Answer

The top light is out, the right light is out, but comes on when it breaks, and the left light is on but does not break. Replacing the bulbs does not help. What should i do

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Check the ground wire

Posted on Jul 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right rear break light doesnt come on


check the ground wire that is most likely the problem. also on some there is a fuse rare but sometimes there is one .

Jan 13, 2014 | 2005 Volkswagen Sharan 1.9

1 Answer

Break light problems


I suggest to check ground connections.

Nov 20, 2012 | Cars & Trucks

2 Answers

Break lights, turn signals not working properly. Left break light only works when right signal is on. All fused have checked okay.


Without being there to actually do some checking, I'd take a look at the signal switch itself. (In the top of the column) First though, check the bulbs, as I have seen (but rarely) a filament in a bulb break and re-connect itself to the other leg of the circuit.

May 05, 2011 | 1983 Chevrolet Silverado

1 Answer

My middle break light comes on but the break light to the right and the left of of the middle light are not coming on. I've checked the fuses and the bulbs. Any suggestions on what the problem is and how...


Check the two outside bulbs to see if they are the same model of bulb that is in the middle. I'm thinking that the two outside bulbs are just taillights and not brake lights.

Dec 25, 2010 | Oldsmobile Alero Cars & Trucks

1 Answer

Bulb failures with no real pattern


check the front and rear turn signal and brake bulbs ,check for filament wear or drakness in bulb glass.if this is found replace bulb,you may also have a bad ground to a bulb socket, turn lights on (signal and break) and wiggle wires at bulb socket, watch light, if it dim any replace that socket and check the ground wire.

Mar 04, 2010 | 1989 Jaguar Vanden Plas

1 Answer

Brake Lights


could be 1 of 2 things. a wiring issue, or the bulbs may simply need to be pulled out and contacts cleaned. sometimes the bulbs contacts will wear or get a film of humidity on them causing them to intermittenly come on and off.

Apr 21, 2009 | 2001 Volvo S80

1 Answer

How replace break light bulb in on a4 2005


Replacement of any bulb in the Tail-light assembly is easier then one thinks.

First thing you need to do is gain access to the trunk area. At the top of
the tail-light area inside the trunk is a small circle that needs to be
opened to expose the bolt that you need to remove.

WARNING: Be careful not to loose this bolt or you are going to have to take
apart your trunk interior to retrieve it.

After the bolt is removed the Tail-light assembly will pull out as follows;
Left side: pull out the right side of the assembly
Right side: pull out the left side of the assembly.
The out side of the assembly is held in place by 2 or 3 small nipples.

There will only be one cable that is connected to the assembly. This does not
have to be removed unless you really want to. On both sides of the assembly
there are 2 clips that hold the light plate to the break light lens. After
the clips are loosened the whole light bulb assembly can be removed and the
bulbs replaced.


Restoring the Break-light assembly.

After you have replaced your bulbs and re attached the the bulb assembly, you
will have to first fit the nipples on the outer side of the assembly then
push the inter side into place. Replace the bolt and tighten. You are done.

Jul 14, 2008 | 2005 Audi A4

Not finding what you are looking for?
2003 Jeep Liberty Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...