Question about 2006 Chrysler Sebring

1 Answer

Fan only works on High

Just all of a sudden. No matter what setting, the fan only works on High speed

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 180 Answers

U will need to replace the swich

Posted on Jul 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blower fan not working.


Possible speed control is open circuit or the fan motor. Check you have supply to the switch/motor.

Apr 01, 2017 | 2006 Chevrolet Malibu LT

1 Answer

Mercedez e200 model 2004 fan speed problem


I assume you mean your fan will only go to a high or low setting no matter what speed you set on your panel? That is most likely going to be your resistor for the fan.

Nov 04, 2012 | Cars & Trucks

1 Answer

Why wont my a/c or heater fan come on?


When the blower works only on the high setting its usually a bad blower resistor which is right near the blower motor. now you say it would always blow high regardless of the fan speed setting that would indicate probably the climate control unit or a connector problem somewhere. finally it not working at all may be the climate control unit or connection went bad even further. it might have a blown fuse or a bad blower motor in addition to the climate control unit or connector problem .check for power and ground at the blower motor. the power is supplied from fuses and may have a relay also. the ground is supplied from the climate control unit and goes through the resistor to control the fan speed. good luck

Oct 30, 2011 | 1997 Lincoln Continental

1 Answer

Fan control knob on a/c and heater will only run on high speed. 2003 dodge mini van


I replaced the fan module under the glovebox on my 2005 Town & Country last night. Mine would not shut off at all with key on. It only blew on high no matter where I set the switch. Mine also had the climate control which makes a difference. If it is not the auto climate control it is usually the blower resistor if the other fan speed selections don't blow at all except on high.

Jun 06, 2011 | 2003 Dodge Grand Caravan AWD

1 Answer

AC and Heater fan will only work on high speed, all fuses good. any ideas thanks, Dave


When the blower fan will only work on high speed setting this means the fans speed control resistor is burned out, when it fails the fan defaults to high speed only. The fan resistor is located next to the fan and held into the cooling air duct by 2 screws near the blower motor. The part is fairly cheap and easy to replace.

May 11, 2011 | 2000 Mercury Villager

1 Answer

Fan on High Only


The fan motors use a set of resistors to control fan speed. The lower speeds generate more heat in the resistors and these tend to burn out. While it is possible the switch could be the issue, I would start with the resistors. It is usually a module located somewhere near the blower motor.

Note: One of the reasons these go out, is that with time the bearings on the blower motor go bad and the motor takes more power to run. If the replaced resistors fixes the problem, but then fail too soon, look at replacing the blower motor as well.

Aug 29, 2009 | 2005 Ford Excursion

1 Answer

Heater Fan does not work


Sounds like the fan control knob has shorted out. You can check the fan "blower" relay and fuse in the engine compartment but you need to make sure the control knob is good or you will keep blowing fuses and relays. If your blower fuse and relay are good, then just have the control knob checked and replaced if needed.

May 08, 2009 | 1999 Volkswagen Passat

1 Answer

Fan on high setting all the time, and won't quit


You need to replace the blower resistor/relay.

Mar 02, 2009 | 2000 Pontiac Grand Prix

Not finding what you are looking for?
2006 Chrysler Sebring Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...