Question about 1991 Toyota Tercel

1 Answer

What the timing belt position - 1991 Toyota Tercel

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,757 Answers

My apologies for the delayed response. I am going back to answer unanswered questions.

CLICK
on the following LINK. It has all the Diagrams for your Timing Belt that you will need.
If you would: Before Clicking let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks!

http://www.2carpros.com/car_repair_information/year/1991/make/toyota/model/tercel/1991_toyota_tercel_timing_belt_diagram_marks.htm

Posted on Mar 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Problems of gm


You can rotate the cam/crank into a positon that will not move as you remove the old belt, as long as the new belt places the cam/crank in same position as the old belt had them, it don't matter where the timing marks are. Leave your old belt on, rotate to a position that will not move or have tension on belt, (no matter the marks) and replace the belt. Make sure to recheck timing marks after new belt is installed by rotating the crank/cam back to timing marks, or just trust that the belt was replaced without the cam or crank rotated. Easy off, easy on, just make sure the cam/crank are still in time as the old belt had them located. NOTE: timing marks are there in case of a broke belt, or for a car that has jumped time. As long as cam and crank are held in same positon, and car was in time before the procedure, it don't matter where the timing marks are at during belt replacement.

Dec 15, 2013 | Cars & Trucks

1 Answer

Were is ford escort timing marks position


I assume timing belt and that you have the Ford engine not the Mazda 1.8L used in tghe GT
. disconnect negative side of the battery
2. place cylinder no.1 TDC compression stoke
3. remove drive belt and tensioner
4. remove timing belt cover
5. raise and support car
6. remove right front tire and splash shield
7. remove crankshaft pulley
8. align timing marks
9. loosen timing belt tensioner
10. remove timing belt
water pump should be check and replaced too

11_4_2012_6_19_59_pm.jpg

11_4_2012_6_20_27_pm.jpg

Nov 04, 2012 | Cars & Trucks

2 Answers

How do I time a 1994 dodge caravan 3 0L Problem PLEAS IF ANY ONE HAVE THE DIGRAM


Is this what you needed?

jturcotte_1784.gif

Fig. Fig. 14: Sprocket timing for belt installation-3.0L engines


0900c15280215dd8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 15: Secure the sprocket when removing or installing the nut-3.0L engines


0900c15280215dd9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 16: Timing belt tensioner-3.0L engines


0900c15280215dda.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 17: Positioning the tensioner-3.0L engines
The timing belt can be inspected by removing the upper (front outer) timing cover.

  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts.
  3. Remove the timing belt covers.
  4. Identify the timing belt running direction to avoid reversal during installation.
  5. Loosen timing belt tensioner bolt and remove timing belt.
  6. Remove the crankshaft sprocket flange.

To install:
  1. Rotate the crankshaft sprocket until timing mark on crankshaft sprocket is lined up with the oil pump timing mark at 1 o'clock position.
  2. Rotate the (inner) camshaft sprocket until mark on (inner) camshaft sprocket is lined up with the timing mark on alternator bracket.
  3. Rotate the (outer) camshaft sprocket (radiator side) until mark on the sprocket is lined up with the timing mark on the timing belt inner cover. Refer to timing belt illustration.
  4. Install the timing belt on the crankshaft sprocket while maintaining pressure on the tensioner side.
  5. Position the timing belt over the camshaft sprocket (radiator side). Next, position the belt under the water pump pulley, then over the (inner) sprocket and finally over the tensioner.
  6. Apply rotating force in the opposite direction to the camshaft sprocket (radiator side) to create tension on the timing belt tension side.
  7. Rotate the crankshaft in a clockwise direction and recheck engine timing marks.
  8. Install the crankshaft sprocket flange.
  9. Loosen the tensioner bolt and allow tensioner spring to tension the belt.
  10. Again rotate the crankshaft in a clockwise direction (2) full turns. Recheck the engine timing. Tighten the tensioner bolt to 23 ft. lbs. (31 Nm).
  11. Install the timing covers.
  12. Install the accessory drive belts.
  13. Connect battery negative cable.

May 29, 2011 | Dodge Caravan Cars & Trucks

2 Answers

Seat belt buzzer , how do you turn it off.


Hope this helps ya.. Cobra.. :-)

Belt-Minder® Deactivating/Activating Vehicles Built After 5/27/03
Preparation
  1. Before deactivating/activating the belt minder, set the parking brake.
  1. Place the transmission range selector lever in PARK.
  1. Place the ignition switch in the OFF position.
  1. Close all the vehicle doors.
  1. Unbuckle the driver and passenger safety belts.
Deactivating/Activating
  1. Turn the ignition switch to the RUN position. (Do not start the engine.)
  1. Wait until the safety belt warning lamp turns off (approximately 1 minute).
  1. NOTE: Step 3 must be completed within 50 seconds after the safety belt warning lamp turns off or the procedure must be repeated.
    For the seating position being disabled, buckle then unbuckle the safety belt 9 times, ending with the safety belt unbuckled.
  1. NOTE: After Step 3, the restraint system warning indicator lamp turns on for 3 seconds.
    Within 10 seconds of the safety belt warning indicator turning on, buckle then unbuckle the safety belt.
  1. The beltminder activation or deactivation is confirmed by the following sequences:
    • If the beltminder is enabled, this procedure will disable the beltminder for that specific seating position. The safety belt warning indicator lamp will flash 4 times per second for 3 seconds to confirm that the deactivation procedure was successful.
    • If the beltminder is disabled, this procedure will enable the beltminder for the specific seating postion. The safety belt warning indicator lamp will flash 4 times per second for 3 seconds followed by a second series of 4 flashes per second for 3 seconds to confirm that the activation procedure was successful.
  1. After confirmation, the deactivation/activation procedure is complete.
Vehicles Built Prior To 5/27/03
Preparation
  1. Before deactivating/activating the belt minder, set the parking brake.
  1. Place gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission).
  1. Place the ignition switch in the OFF position.
  1. Close all the vehicle doors.
  1. Unbuckle the driver safety belt.
  1. Place the parklamps/headlamps switch in the OFF position. (if vehicle is equipped with Autolamps, this will not affect the procedure.)
Deactivating/Activating
  1. Turn the ignition switch to the RUN position (Do not start the engine.)
  1. Wait until the safety belt warning lamp turns off (approximately 1 to 2 minutes).
  1. NOTE: Steps 3 through 5 must be completed within 60 seconds or the procedure must be repeated.
    Buckle then unbuckle the safety belt 3 times, ending with the safety belt unbuckled. This portion of the procedure can be done before or during belt minder warning activation.
  1. Turn the parklamps/headlamps on then off.
  1. Buckle then unbuckle the safety belt 3 times ending with the safety belt unbuckled. After this step the safety belt warning lamp will be illuminated for 3 seconds.
  1. Within 7 seconds of the safety belt warning lamp turning off, buckle then unbuckle the safety belt. This will enable the belt minder if disabled and disable the belt minder if enabled.
  1. The following sequence of events confirm the belt mnider is enabled:
    • flashing of the safety belt warning belt lamp 4 times per second for 3 seconds
    • 3 seconds with the safety belt lamp off
    • flashing the safety belt lamp 4 times per second for 3 seconds again
  1. The safety belt lamp flashing 4 times per second for 3 seconds provides confirmation of belt minder disabled.
  1. After confirmation, the deactivation/activation procedure is complete.


Jun 15, 2010 | 2004 Ford F150

2 Answers

How to changing a timing belt on a 2000 ford focus SE


FOR A 2.0 SPI ENGINE:
Removal
  1. Remove the accessory drive belt.
  2. Detach the coolant expansion tank.
  3. Remove the bolt and position the expansion tank to one side. Detach the power steering reservoir and position to one side.
  4. Remove the right-hand front wheel and tire.
  5. Remove the crankshaft pulley/vibration damper.
  6. Lower the vehicle. Disconnect the ignition wires from the spark plugs.
  7. Remove the two ignition wire separators from the valve cover.
  8. Remove the spark plugs. Place a jack with a wooden block under the oil pan and raise slowly until the front engine mounting is free from strain.
  9. Remove the engine front mounting. Remove the timing belt cover.
  10. Remove the engine front mounting bracket. Align the timing marks.
  11. Remove the timing belt. Use an 8 mm Allen wrench and turn counter clockwise 1/4 turn.
  12. Insert a 3 mm (1/8 inch) drill bit to lock the timing belt tensioner in place.
  13. Remove the timing belt.

Installation
  1. Check the alignment of the timing mark on the crankshaft timing belt pulley.
  2. Check the alignment of the timing mark on the camshaft timing belt pulley.
  3. Install the timing belt. Install the timing belt over the pulleys in a counter clockwise direction starting at the crankshaft.
  4. Keep the belt span from the crankshaft to the camshaft tight while installing the timing belt over the camshaft.
  5. Remove the 3 mm (1/8 inch) drill bit to release the timing belt tensioner.
  6. Turn the crankshaft at least two turns in clockwise direction to TDC position for cylinder one.
  7. Check the alignment of the timing marks.
  8. If the alignment is not correct repeat the previous steps. Install the engine front mounting bracket. Install the timing belt cover.
  9. Install the engine front mounting. Remove the jack. Install the spark plugs.
  10. Push on the spark plug connector until it engages.
  11. Raise and support the vehicle. Install the crankshaft pulley/vibration damper.
  12. Position the drive belt on the crankshaft pulley.
  13. Install the right-hand front wheel and tire.
  14. Install the power steering reservoir.
  15. Install the coolant expansion tank. Install the accessory drive belt.

Nov 10, 2009 | 2000 Ford Focus

1 Answer

Timing belt timing marks, 1997 ford escort where are they?


Ford Escort/Tracer 1991-1999 Repair Guide

REMOVAL & INSTALLATION 1.8L Engine

(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers.
  3. Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
  4. Remove the crankshaft pulley and hub.
  5. If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
  6. Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
  1. Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
  2. Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
  3. Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
  4. Install the timing belt.
  5. Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
  6. Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.

fbe49f2.jpg
Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

5bb74d0.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

9cafc26.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

72dc9cd.jpg
Fig. 4: Check the timing belt deflection at the location shown-1.8L engines

  1. Make sure the camshaft pulley marks are aligned with the seal plate marks.
If the timing marks are not aligned, remove the belt and repeat the procedure.


I hope help you with this; remember rated this help. Good luck.

Sep 11, 2009 | 1997 Ford Escort

1 Answer

Timing belt position


crankshaft sprocket up on timing mark, the exaust timing on the shield behind the timing gear. it will be E on the exaust cam gear and the I in the intake cam gear. then install belt.

May 03, 2009 | 2001 Kia Sportage

1 Answer

My timing belt broke on my '99 Ford Escort ZX2. Please tell my husband how to replace it. Than k you



 
 
Timing Belt
REMOVAL & INSTALLATION
1.8L Engine
Disconnect the negative battery cable.
Remove the timing belt covers.
Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
Remove the crankshaft pulley and hub.
If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
Install the timing belt.
Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.
Fig. 1: Timing marks are located on the camshaft pulleys as shown — 1.8L engines


 
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned — 1.8L engines


 
Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position — 1.8L engines


 
Fig. 4: Check the timing belt deflection at the location shown — 1.8L engines

Mar 28, 2009 | 1999 Ford Escort

3 Answers

Need a timing scamatic for a 1998 ford contour 16v Zetec ct 2.0l


Installation
All Vehicles
  1. NOTE: Rotate the crankshaft clockwise.
    Rotate the crankshaft to TDC on cylinder No. 1.
6d7ac03.gif
NOTE: Cylinders No. 1 and No. 4 are at TDC when the Woodruff key points straight up.
Remove the blanking plug, completely screw in the special tool and auto-align the crankshaft to TDC.

0889b40.gif
  1. Position cylinder No. 4 to valves overlap" and install the special tool.
  2. Hold the camshafts by the hexagon using an open-ended wrench and turn them in the direction of engine rotation.
  3. Slide the special tool onto the ends of both camshafts.
6971087.gif
swp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not kink the timing belt (do not bend the timing belt less than a diameter of 35 mm).
swp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not rotate the crankshaft; as necessary check that it is still resting against the timing pin.
NOTE: Design with lower idler pulley shown (built up to 06/1999).
NOTE: The lug of the belt tensioner should not be hooked in the sheet metal cover during timing belt installation.
Position a new timing belt in place.
  • Starting from the crankshaft timing belt pulley and working counterclockwise, position the timing belt in place while keeping it under tension.

2907f65.gif
  1. swp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not rotate the crankshaft; as necessary check that it is still resting against the timing pin.
    NOTE: Design without lower idler pulley shown (built 06/1999 onwards).
    NOTE: The lug of the belt tensioner should not be hooked in the sheet metal cover during timing belt installation.
    Position a new timing belt in place.
    • Starting from the crankshaft timing belt pulley and working counterclockwise, position the timing belt in place while keeping it under tension.
143871c.gif
  1. NOTE: Incorrect timing belt tension will cause incorrect valve timing.
  2. Pre tension the timing belt.
  3. Rotate the tensioner locating tab counterclockwise and insert the locating tab into the slot in the rear timing cover.
  4. Position the hex key slot in the tensioner adjusting washer to the 4 o'clock position.
  5. Tighten the attaching bold enough to seat the tensioner firmly against the rear timing cover, but still allow the tensioner adjusting washer to be rotated using a 6mm hex key.
0afbc96.gif
CAUTION: Tension the timing belt, working counterclockwise. Using the hex key, rotate the adjusting washer counterclockwise until the notch in the pointer is centered over the index line on the locating tab (the pointer will move clockwise during adjustment).

4e30913.gif
While holding the adjusting washer in position, tighten the bolt
NOTE: Hold the intake timing belt pulley with special tool to stop it from turning.
Tighten the timing belt pulleys.
  1. Tighten the intake camshaft timing belt pulley bolt.
  2. NOTE: Hold the exhaust camshaft by the hexagon with an open-ended wrench to stop it from turning.
    Tighten the exhaust camshaft timing belt pulley bolt.
  3. Remove the special tool.
    • Install the blanking plug.
  4. Remove the special tool.
  5. NOTE: Hold the camshaft by the hexagon with an open-ended wrench to stop it from turning.
    Tighten the exhaust camshaft to stage 2.
    1. NOTE: Turn the crankshaft two revolutions in the normal direction of rotation.
      Check the valve timing by inserting the special tool. Correct it, if necessary.
      • Screw in special tool 303-574 and make sure that the crankshaft is touching it.
      • Insert special tool 303-465 into the camshafts; if necessary loosen the timing pulleys and correct the camshaft alignment.
      • Detach the special tools.
    1. NOTE: Use a new blanking plug.
      Install the blanking plug on the exhaust camshaft pulley.

Mar 10, 2009 | 1998 Ford Contour

Not finding what you are looking for?
1991 Toyota Tercel Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...