Question about 1994 Plymouth Grand Voyager

2 Answers

Need to remove the alternator

Can you please provide step by step instructions for removing the alternator from a 2000 Plymouth Grand Voyager SE with a 3.3L engine? Thanks

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Remove windshield wiper blades (mark the arm and stud to put back exact). The next two steps you might have to lower/raise the hood. Remove cover just below the windshield(each end has a phillips screw turn 90 degrees so arrow points toward center of van). Remove the 4 metal braces. Remove windshield wiper motor/linkage assembly(the whole tray comes out). Remove drive belt. Disconnect negative side of the battery. Remove alternator horizontal mounting bracket. Loosen vertical bracket bolts to get to electrical connectors. Finish removing bolts and alternator.

Posted on Jul 24, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 123 Answers

Go to a nearby workshop

Posted on Jul 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install alternator ground wire and alternator in 1997 Plymouth Grand Voyager SE


The alternator is self grounded when installed. There is no ground wire
Remove the 3 bolts holding it on
unplug the wires remove belt from pully
install new do not tighten yet
put belt back on pully and pull alt till belt is tight hold there and tighten bolts
plug in elect wires
test
MDS

Nov 03, 2015 | Plymouth Cars & Trucks

1 Answer

How do i change out a torque converter for a 2000 plymouth grand voyager se??


Drop the transmission and replace convertor and then reinstall. Not a DIYS job, you really need a lift

Jan 04, 2015 | 2000 Plymouth Grand Voyager

1 Answer

How can I down load the user manual for a 1993 Plymouth grand voyager SE?


Plymouth.com/manuals Look for your year. You may have to look under archives.

Dec 28, 2014 | 1993 Plymouth Grand Voyager

1 Answer

I need to replace a water pump on my plymouth grande voyager se 3.3l


Jack up the passenger side and remove the tire. Remove the splash shield to gain access to the belt and tensioner. Remove the serp belt. Remove the bolts holding the pulley to the water pump. Remove the pulley Remove the bolts holding the water pump to the timing cover. Remove the water pump. Be prepared for the bolts to break. It happens often!

Jul 13, 2013 | Cars & Trucks

1 Answer

How to replace an alternator on a plymouth grand voyager


well what kind of engine you have? on 3.0L the alternator is at the front right side of the engine on the top. there are two bolts to remove one you can see just by looking at it but the other one is in the back and you cant see it. just feel with your hand where is it and you socket n rachet and remove it and disconnect the wire that are connected to the alternator. CAUTION: before you remove the bolts take the belt off by turning the belt tensioner clockwise. hope it helps.

Dec 30, 2010 | 2000 Plymouth Grand Voyager

1 Answer

How to take out alternator on a voyager 2000 model


What Size Engine Do You Have? Do you have AC or no AC? These make a huge difference in the Step by Step Instructions you will receive!
Let me know in the Comments Section of your Posting and I will Reply!
Thanks!

Feb 06, 2010 | 2000 Plymouth Grand Voyager

1 Answer

How to remove altenator for 1999 Plymouth Grand Voyager 3.3 litre


Before the step-by-step instructions I want to make sure this is the Alternator that needs to be replaced and not something else. This will save you money for an Alternator you don't need and save you time for replacing a good alternator.
Start the vehicle. With the engine running - disconnect the Negative Cable from the Battery. If the Engine dies - it is the Alternator. If it doesn't die - it is not the Alternator. I have had plenty of people who have replaced perfectly good Alternators only to find out it was something else.
Step-by-step:
1. Disconnect the Negative Cable from the Battery.
2. Using a 15mm closed end wrench/bar - Rotate the Belt Tensioner towards the front of the vehicle and remove the Surpentine Belt off the Alternator. You do not have to take it completely off the vehicle.
3. Remove the bolt holding the top of the Alternator Mounting Bracket to the Engine Air Intake.
4. Remove the bolts (plural) holding the outside of the Alternator Mounting Bracket to the Alternator Mounting Plate.
5. Remove the bolt holding the top of the Alternator to Alternator Mounting Bracket.
6. Remove the Alternator Mounting Plate.
7. Remove the the Altenator Mouting Bracket.
8. Rotate the Alternator towards the rear.
9. Discoonect the electrical connections (plural), including the nut holding the wire on.
10. Remove the lower Pivot bolt located at the bottom of the alternator.
11. Remove the alternator.
12. Installation is reverse of above.
Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Jan 11, 2010 | 1999 Plymouth Voyager

1 Answer

1996 Plymouth grand voyager se-need diagram showing where body control module would be located.


The BCM is located on the drivers side under the the steering column. It is behind the fuses and to get to it you have to remove the bash board plastic, than a pice of metal and than you have to remove the fuses box. It will take you approximately 20 min to remove everything. Once you remove the BCM you need to take note of the Part Number P/N. It has to be the same P/N on the replacement BCM. You can use any BCM from years 1996-2000 but make sure the electrical configuration is the same as yours (Power windows, alarms, etc.). I bought my BCM on the junk yard for 35 dollars and my car works perfectly.
I hope this may have assisted you,
Tom

Oct 28, 2009 | 1996 Plymouth Grand Voyager

Not finding what you are looking for?
1994 Plymouth Grand Voyager Logo

576 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...