Question about 1997 Hyundai Accent

2 Answers

Daignostics shown that the computre box needs to replaced

Daignostics shown that the computre box needs to be replaced.After fitting two boxes with the same serial number than the one installed, the vehicle won't start .At first we pluged the computer box in of the person that did the diagnostics (his spare) then he did a diagnostisc test again and the vehicle was running smooth and nice. The first box that I've purchest at a 2nd hand shop was not giving me the results that i've hoped for. When I plugged it in and try to start the vehicle it was mis firing and splatter when I press the accelerator. I then plugged it out and plugged my original computre box in .but the car was now in a worse condition. I've tried another box ,but the same results. Since then i've changed the airflow meter and the idle speed activator. but the vehicle will not start. I will go and start testing the wrea from the fuel pump. Please advise me

Posted by on

  • Anonymous Mar 25, 2014

    when I plugged the sensor on a different vehicle it came on

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Hyundai Master
  • 1,348 Answers

Unhook the battery for a few minutes.the ecu needs to relearn all the data

Posted on Jul 18, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 850 Answers

Disconnect battery when changing pooters
then scan it

Posted on Jul 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 mercury mountaineer that wont turn over at all the battery is good and there's a clicking noise coming from the relay box what would that be


The clicking noise will be relays. Possibly a starter relay and thats normal. Sounds as if the starter moter may be the culprit. You have to check for start power at the starter solenoid while cranking before any further daignostics can be done. Sometimes tapping on the starter motor while holding the key in the crank position will start the vehicle. If so the stater motor is defective

Apr 10, 2015 | 2002 Mercury Mountaineer

1 Answer

What engine is in the truck with this serial number 1ftef26h3epa74301


There is no vehicle shown here

Firing Order is shown on the internet
on dozens of places

You use Vin # for the engine code

At least here in north america

No idea why Europe needs the engine block numbers
& such,I guess has to due with motor vehicle agencies
& emission inspections

Aug 16, 2014 | Cars & Trucks

1 Answer

Looking at the fuze box in a 1996 BMW 328i, the drivers seat adjustment fuse is #40. Where is the #40 fuze located?


Fuse box should look like the one shown on these pages:

Fuse box diagram BMW 3 E36
http://bmw-e36.com/repair/8-bmw-e36-fuse-box-diagram-318i-1996.html


The longer single row of fuses is #31-46 (46 is closest to the double row of fuses).


Hope this helps!

Feb 28, 2018 | 1996 BMW 328i

1 Answer

How do I install a belt tensioner for my 93 buick


CAUTION To avoid personal injury when rotating the serpentine belt tensioner, use a tight fitting wrench that is at least 24 in. (61cm) long.
  1. Take note of the belt's routing. Lift or rotate the tensioner using a suitable sized breaker bar in the square opening or box end wrench on the pulley nut. Remove the belt from the pulleys.



0996b43f8021adee.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 8: You can use a box-end wrench on the pulley nut to rotate the tensioner ...


0996b43f8021aded.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 9: ... then remove the belt from the pulleys


0996b43f8021adc9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 10: Serpentine drive belt routing and removal - 3.8L (VIN L) engine shown, VIN C similar


0996b43f8021adca.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 11: Make sure to note the drive belt routing prior to removing it - 3.8L (VIN K) engine shown


0996b43f8021adcb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 12: Drive belt removal on a 1992-95 supercharged engine
To install:
Be sure the belt is aligned into the proper grooves of the accessory drive pulleys.

  1. Lift the tensioner, and install the belt onto pulleys. Make sure the belt is routed properly.



0996b43f8021adf6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 13: Many vehicles have a label you can check to be sure the belt is installed and routed correctly

  1. For 1996-99 vehicles, raise and safely support the vehicle. Install the engine mounting bracket lower spacer, stud and nut.
  2. For 1996-99 supercharged engines, perform the following:
    1. Attach the connector to the crank sensor.
    2. Install the right-hand splash shield, then carefully lower the vehicle.
    Once you have the belt off there should be 1 bolt in the middle of the tensioner losen the bolt and remove the tensioner.
  3. Install the belt guard or reservoir.
  4. Connect the negative battery cable

May 11, 2012 | 1993 Buick LeSabre

1 Answer

Steering fluid leak; oil covering steering gear box


if the leak is coming from the steering box there are usually only 3 places it can come from;most common place is the pitman shaft seal,which can be replaced.this is were the pitman arm of the steering connects to the steering box.another place is the steering box input shaft seal,this is were the steering colume connects to the steering box,which can be replace.the last place is the power steering hoses were they connect to the steering box.there are seals that seal the lines when screwed into the box which can also be replaced.so first you need to see exactly were the leak is coming from.rare occasions the steering box is porous which means the box will need replacing.a car of this age should have shown up long ago.you will have to clean the box off at the car wash then run the car and turn the steering wheel all the way to one side,this will build up pressure in the system to show up the leak quicker.

Apr 04, 2012 | 2000 Jeep Wrangler

1 Answer

2000 alfa 156 stuck in gear (reverse), wont start. 2 mechanics had a look, couldnt fix it. its been 4 days and still at the workshop. please help...


Hi Regelyn,
Bad news because the box will have to be removed and the selector rods and forks will need to be checked and sorted out. You may do better to look for a second hand gearbox and have your shop mechanics fit it for you. Even if your mechanics manage to get it out of gear, something is wrong inside the box for the fault to have shown up in the first place and in all likelihood will happen again.
Regards Johngee10

Feb 08, 2011 | 2000 Alfa Romeo 156

2 Answers

I need to replace the horn fuse in my 1997 mercury mountaineer


In your owners manual go to the index and look for fuses then go to that page. Look for the horn fuse which should be in the fuse box under your hood around your engine, in your owners manual is should tell you where it's located. Find the fuse for it by looking at the diagram on your owners manual and then pull that fuse out. You should have replacement fuses in the fuse box that's in your car, you have to open the car door to get to it. If you don't have that fuse just take it up to auto zone and tell them you need a replacement for that fuse.

Dec 14, 2010 | 1997 Mercury Mountaineer

1 Answer

The radio says code and i need the code how do i get one


Call (1-888-648-7820)

As part of the radio's anti-theft system on some older model year vehicles (2002 and older), the radio resets itself whenever it loses power from the vehicle's battery. Radio security codes are associated with each individual radio unit rather than the vehicle identification number (VIN) (since a vehicle could have the radio replaced). The radio security code must be input in the radio in order for the radio to work.

When you purchased your vehicle, you should have received a card that lists the four digit security code for the radio. If you are unable to locate this card (sometimes owners find it inserted in the Owner's Manual or glove box), the radio will need to be removed so that you can locate the Part Number and Serial Number for your specific radio. The Part Number typically begins with the letters 'MR' and the Serial Number is generally a string of digits and both numbers can be located on the audit unit's chassis.

stereo.jpg
stereo_card.jpg

Please contact your local Authorized Mitsubishi Dealer if you need assistance removing the radio. Once the Part Number and the Serial Number are in hand, your Dealer can access the security code for that radio. You may also contact our Customer Relations Call Center at 1-888-MITSU2011 (1-888-648-7820) and one of our agents will be happy to provide you with the security code and steps to reset the radio as long as you have the Part Number and Serial Number for your radio unit. Agents are available Monday-Friday 7 a.m. to 4 p.m. (PT). Best of all they will give it to you free

urnuts73.jpg

Oct 30, 2010 | 1998 Mitsubishi Montero

1 Answer

Is the radio code for a 2003 escalade in the glove box?


HI. Actually, your code will be located in the drivers manual. This vehicle manual should be located inside the Glove box. If you have lost your vehicle manual, you will need retrieve the radio serial number, and contact your local dealership for the correct code. The ,radio/cd players serial number, will be located on the rear, or bottom side of the exterior of the radio cover. This will require you to remove the radio from the dash to expose the sticker, on the radio cover.

Nov 30, 2009 | Cadillac Escalade Hybrid Cars & Trucks

Not finding what you are looking for?
1997 Hyundai Accent Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...