Question about 2000 Plymouth Voyager

2 Answers

Where is the water pump located on a 99 plymouth voyager, 3.0Lit?

What parts do I have to remove to get to the water pump?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 323 Answers

It is driven by the timing belt. You'll need to support the front of the engine, remove the mount and timing covers. The pump sits in the center between the heads and has a tube running into the back of it that sometimes is difficult to get out. If you are uncomfortable with setting up the timing belt you may want to have a professional do the job.

Posted on Jul 24, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 227 Answers

I have a 2000 plymouth voyager with the 3.0 ltr. If i am not mistaken the engines are the same, and if that being the case, the water pump is located behind the timing cover. It is also driven by the timing belt, so while in there making the repair to the water pump you should go ahead and throw a new timing belt on there.

Posted on Jul 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to change water pump in 99 plymouth voyager 3.0 liter


  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the drive belts. Remove the timing belt covers and the timing belt.
  4. Remove the water pump mounting bolts.
  5. Separate the water pump from the water inlet pipe and remove the water pump.
  6. Inspect the water pump and replace as necessary.

To install:
  1. Clean all gasket and O-ring surfaces on the water pump and water pipe inlet tube.
  2. Wet a new O-ring with water and install it on the water inlet pipe.
  3. Install a new gasket on the water pump.

  1. Install the pump inlet opening over the water pipe and press until the pipe is completely inserted into the pump housing.
  2. Install the water pump-to-block mounting bolts and tighten to 20 ft. lbs.
  3. Install the timing belt and timing belt covers. Install and adjust the drive belts.
  4. Reconnect the negative battery cable. Fill the cooling system to the proper level with a 50 / 50 mixture of clean, ethylene glycol antifreeze and water.
  5. Run the engine and check for leaks. Top off the coolant level, if necessary.

Oct 16, 2013 | 1997 Plymouth Voyager

1 Answer

I need to replace a water pump on my plymouth grande voyager se 3.3l


Jack up the passenger side and remove the tire. Remove the splash shield to gain access to the belt and tensioner. Remove the serp belt. Remove the bolts holding the pulley to the water pump. Remove the pulley Remove the bolts holding the water pump to the timing cover. Remove the water pump. Be prepared for the bolts to break. It happens often!

Jul 13, 2013 | Cars & Trucks

1 Answer

What all is involved in replacing the water pump on a 99 Plymouth grand voyager 3.3l


Not much. Jack up on the right side, remove the wheel, and the shroud, remove then serp belt, take out the bolts, and replace the pump. You can try to drain the system first, but we usually catch what we can and add new coolant.

Apr 28, 2011 | 1999 Plymouth Grand Voyager

1 Answer

How do I remove oil pump on 2000 Plymouth voyger


The oil pump removal procedure for Plymouth Voyager 2000.
A oil pump is usually located in the oil pan. If you want to change the oil pump and replace it with a new one, roll up your sleeves and get ready for some dirty work.
The procedure to remove oil pump is as follows:--
  • Drive your vehicle up onto ramps or lifts so you have room to work as you pull out the oil pump. You could also use a jack, but make sure you brace the front wheels so they don't roll. In addition, set the emergency break firmly into position so the car doesn't roll.
  • Remove the engine front cover then drain the engine oil and take out the oil pan. It is under the engine and looks like the bottom of the motor.
  • Unscrew the oil pump mounting bolts with a wrench and proceed to remove the oil pump itself by pulling it down and out of the engine. Avoid getting any contaminants into the oil pump assembly while removing.
The Water pump removal procedure for Plymouth Voyager 2000.
The water pump is the heart of the Plymouth Voyager's cooling system, circulating the coolant. When the water pump is faulty, it can cause serious damage to the engine of your Plymouth Voyager.
  • Disconnect the negative battery cable.Place a drain pan underneath the radiator. When the engine is cool, drain the cooling system from the radiator into the pan.
  • Remove the right inner splash shield and the accessory drive belts. Support the engine underneath and remove the right motor mount with the bracket.
  • Take off the front cover and remove the timing belt along with the timing belt idler pulley. Also remove the camshaft sprockets, the rear cover to the timing belt and the alternator with its bracket.
  • Loosen and remove the bolts to the water pump and remove it from the engine.Install the new water pump after inserting a new o-ring gasket. Tighten the bolts to 105-inch lbs. Make sure that the pump can move freely by rotating it by hand.
  • Replace all components in reverse order. Tighten the camshaft sprocket bolts to 75 foot pounds and the timing belt idler pulley to 45 foot pounds.
  • Refill the cooling system with coolant and reconnect the negative battery cable. Start the engine and check for leaks when it reaches normal operating temperatures.

Loud noises coming from the cooling system could be a sign that your water pump needs replacing. A leak in the coolant may also be an indicator. You can expect that a water pump will need to be changed every 70 to 100 thousand miles or so in a Plymouth Voyager vehicle.
Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Jun 13, 2010 | 2000 Plymouth Voyager

1 Answer

How to change waterpump on a 99 plymoth grand voyager 3.3 motor


i need your help about problem water pump. I did exchanged new water pump. but it keep increase hot up .. i still figure something out about water pump. do you think fan cooling broke either fuse blow out .. thank you ..

Jan 17, 2010 | 1998 Plymouth Grand Voyager

2 Answers

Where is the water pump located 99 plymouth voyager


the reason u can't see the pump is because it is driven by the timing belt and is hidden under the plastic7b4ce03.jpg cover that is over that belt.

Mar 06, 2009 | 1999 Plymouth Voyager

2 Answers

WHERE IS THE WATER PUMP LOCATED ON A 1998 PLYMOUTH GRAND VOYAGER


Here are the steps required to change the water pump on the 3.0L engine.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the drive belts. Remove the timing belt covers and the timing belt.
  4. Remove the water pump mounting bolts.
  5. Separate the water pump from the water inlet pipe and remove the water pump.
  6. Inspect the water pump and replace as necessary.
To install:
  1. Clean all gasket and O-ring surfaces on the water pump and water pipe inlet tube.
  2. Wet a new O-ring with water and install it on the water inlet pipe.
  3. Install a new gasket on the water pump.
  1. Install the pump inlet opening over the water pipe and press until the pipe is completely inserted into the pump housing.
  2. Install the water pump-to-block mounting bolts and tighten to 20 ft. lbs. (27 Nm).
  3. Install the timing belt and timing belt covers. Install and adjust the drive belts.
  4. Reconnect the negative battery cable. Fill the cooling system to the proper level with a 50/50 mixture of clean, ethylene glycol antifreeze and water.
  5. Run the engine and check for leaks. Top off the coolant level, if necessary.
34bef4a.jpg

Jan 12, 2009 | 1998 Plymouth Grand Voyager

1 Answer

Where is the water pump located on a 2000 plymouth voyager 2.3l?


the water pump will be in front of the engine and the belt will go around its pully , there will be the radiator hoses connected to it and also the heater radistor hoses

Nov 23, 2008 | 2000 Plymouth Grand Voyager

Not finding what you are looking for?
2000 Plymouth Voyager Logo

Related Topics:

487 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...