Question about 2001 Hyundai Accent

1 Answer

Showing code 1606 doesnt shift properly wont hardly run until code scanner is hooked up then works perfect ? new engine and computer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 850 Answers

Sorry 1606 is not on my code list
i suggest its the ecu
It might be new, but that still doesnt guarantee its ok

Posted on Jul 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 mazda 6s 3.0 v6. I have a check engine light for Low Barometric pressure. what could cause this issue and what could it affect? also tcs is disabled and i assume it is because of this code


It would be helpful if you included the code you read on the scanner, rather than an abbreviated interpretation of what the scanner gave you. For instance, P0107 means "Manifold Absolute Pressure/Barometric Pressure Circuit Low Input". This indicates that the MAP (manifold absolute pressure) sensor is providing a signal not in agreement with what other sensors are 'telling' the ECM. The MAP sensor is like a vacuum gauge - it is located somewhere in the intake manifold or intake plenum and reports how 'hard' the engine is working to the ECM. These codes indicate there is a problem with the MAP sensor itself or with the wiring between the sensor and the ECM. Double check all the connectors that you disconnected when replacing the valve cover gaskets. As this problem only showed up after you did this work, it's probably a loose connection or pinched wire.

Jan 07, 2017 | 2006 Mazda 6 s

3 Answers

2002 rav4 2.0; when engine is hot doesn't idle and give hard start: tps,GDI,egr,fuel pump,spark plugs and coil are all okay..when its cold first key the engine is fired up


Crank sensor , cam sensor , temp. sensor , Need to have a diagnostic scan tool hooked up ! one that can read engine sensor data !

Apr 22, 2015 | 2002 Toyota RAV4

1 Answer

1995 blazer 4l60e trans just rebuilt. Hard 1-2


Sounds like full pressure apply from pcm. Must check for full 12v at trans connector. Also check all ground twice. That is a hard trans to install and things tend to get left loose.

Sep 11, 2014 | 1995 Chevrolet Blazer

1 Answer

Electronictransmissionlightison


a lot of new cars have a pressure solenoid switch in them that will make car shift hard when they become defective plus also the engine computer controls when your car shifts gears as well. have it hooked up to scanner to check for any default codes .if it is the seloniod it will have a code stored for it a well but also check you transmission fluid to make sure it is not in need of fluid a well. hope this helps thanks 10 zacks

Mar 30, 2014 | 2008 BMW 528i Sedan

1 Answer

Misfires, caughs and spudders under load until at warm operating temp


if it has distributer cap replace it --cud be u need a new computer or havit reflashed--bad ones dont show on a scan--a bad torque converter can mimic engine issues--bad ignition parts like coil-alternator or worn ignition module can also give these symtoms--even a bad themostat that doesnt let motor warm properly--each car is different--dirty throttlbody and idle air controlpossibl--since car is old running a data stream that displays values or voltages can pinpoint bettr then a 40$ scanner

Nov 05, 2013 | 1994 Jeep Grand Cherokee

3 Answers

Why doesnt my engine light go off


Auto Zone will scan your computer and find out what that code is for free (except in CA), just be sure to get them to write them down or print them so you can post them here. Check the fuse for the cigarette lighter, it is probably blown. The owners manual will show you the location of that fuse.

Dec 09, 2011 | 1999 Ford Windstar

1 Answer

Car starts and runs perfectly until engine reaches operating temp then loses power starts poping spitting firing all over the place until it dies. then it wont start again for 2-3 hours until engine cools...


Possibly the catalytic is plugged. How to know? Has this been getting worse over short time period week or two? Check out at exhaust shop..
Good luck.

Aug 18, 2011 | 1997 Chrysler Sebring

1 Answer

I have a1997 Jeep Grand Cherokee LMT v-8 4x4. The code reader said that it is the camshaft sensor bad, but i am then told that the vehicle doesnt have one. the vehicle runs great untill you turn it off. ...


This is common when using a aftermarket scanner to read codes. the problem you are having is a common one. replace the crankshaft sensor, its located at rear of the engine, its hard to see but its there. look at where the engine and tranny meet, i think is on the top near the driverside but if not there then look at pass/side but its near the top of the tranny housing. its common for this, crank sensor problem, good day.

May 10, 2011 | 1997 Jeep Grand Cherokee

2 Answers

My suburban with 4l60e wont shift out of 2nd gear. when you put it in drive, it does fine til time to go into 3rd. it seems to just go into neutral, letting the rpms fly so i just put it in 2nd gear and...


The check engine light should be on. With a scanner pull the transmission control codes. and follow up on their leads speed sensers ( thiers 3 and shift soliods ( thiers 4) the connectors and the wires and more likly to be a problem than hard parts as this transmission is thris on up shifteed sllectonically

May 09, 2011 | 1999 GMC Suburban

Not finding what you are looking for?
2001 Hyundai Accent Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...