Question about 1994 Buick Park Avenue

1 Answer

The switch you use to operate the wipers and operate turn signals broke off what is that part called? and where can I get another one?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

It's calledthe multi function switch and any parts store sell them.

Posted on Jul 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE A 2008 SATURN VUE 3.5 WIPERS WILL NOT PARK OR SHUT OFF OR WILL PARK ANYWHERE I HAVE REPLACED MOTOR AND SWITH STILL HAVE PTOBLEM


Your windshield wiper's are computer controlled by the BCM - body control module . The wiper switch is an input to the BCM , which energizes two different relay's to turn on the wiper's . Taking the vehicle to a qualied repair shop an having diagnostic's run would be your best bet , unless you have a professional scanner that can read DTC'S - diagnostric trouble code's in the BCM !
DTC B3715 00: Front Wiper Relay Drive Circuit
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
This is always the first step in the diagnostic process . An if you do not know how they work ,reading factory service manual info. should be done .
Circuit/System Description
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
Your best bet , take it to a qualified repair shop.

Dec 10, 2017 | Saturn Cars & Trucks

1 Answer

I have a 2009 gmc sierra, where is the wiper relay location.


The PCB wiper relays are soldered directly to circuit board inside the under hood fuse box.
The windshield wiper/washer switch signal circuits are inputs to the body control module (BCM) and the BCM controls wiper motor low speed operation, washer pump and high speed operation. The windshield wiper/washer switch is provided a low reference from the BCM and each of the switch signal circuits is supplied 12 volts through a resistor and monitored within the BCM. During LOW or INTERMITTENT operation the wiper switch low signal circuit is closed to the low reference circuit through a series of resistors within the switch assembly and the signal circuit voltage monitored by the BCM will depend on the switch contact location to the resistor assembly. During HIGH or WASH operation the high and wash switch signal circuits are closed directly to the low reference circuit within the switch assembly and nearly all the signal circuit voltage will be dropped across the BCM resistors. The BCM controls the wiper motor through the WIPER CONTROL PCB Relay and the WIPER SPEED PCB Relay. During any wiper motor function that uses low speed the BCM supplies the voltage to energize the WIPER CONTROL PCB Relay and battery voltage will be supplied from the WIPER CONTROL PCB Relay through the de-energized WIPER SPEED PCB Relay to the wiper motor low speed control circuit. During high speed wiper motor operation the WIPER CONTROL PCB Relay is energized as in low speed and the BCM provides a ground to energize the WIPER SPEED PCB Relay and the battery voltage is supplied to the wiper motor high speed control circuit. Wiper motor park operation is controlled by the BCM using an input from the park switch within the wiper motor assembly. The BCM supplies the park switch signal circuit 12 volts through a resistor then monitors the circuit. Whenever the wiper motor is out of the park position the park switch signal circuit is closed to ground and nearly all the signal circuit voltage will be dropped across the BCM resistor. When the wiper switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the BCM will continue to operate the motor until the wipers reach the park position. If the ignition is turned OFF while the wipers are in mid-cycle, the wipers will stop immediately where they are and the BCM will park the wipers the next time the ignition is cycled ON.

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
Have it checked for DTC'S - diagnostic trouble codes .

The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low.
Your best bet , take your vehicle to a qualified repair shop or dealer . Hooking up a factory scan tool to see what the wiper switch inputs to the BCM are correct and outputs to relays are good .

Feb 11, 2017 | GMC Cars & Trucks

1 Answer

How do I find out if the wipers on my 2006 H3 Hummeris on a relay?


The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Low Speed Operation
When the wiper switch is in the Low position, voltage is supplied through an internal resistor to the signal circuit. The body control module (BCM) monitors the windshield wiper switch signal 1 circuit, and energizes the wiper micro relay which will operate the windshield wiper motor. The wiper motor will operate at low speed, since the wiper 2 relay is de-energized. Low speed can also be commanded with a scan tool, by commanding Wiper Relay Cmd. ON and OFF. Refer to Scan Tool Output Controls .
High Speed Operation
In the High position, the windshield wiper/washer switch supplies voltage to both the wiper micro relay and wiper 2 relay coils. This energizes both relays and allows battery voltage from the wiper micro relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor. The windshield wiper motor will operate at high speed. During high speed wiper motor operation the wiper switch signal circuit is at the low speed signal voltage, and the body control module (BCM) supplies redundant voltage to the wiper relay via the wiper diode.

This info is out of hummer factory service manual !

Dec 10, 2016 | 2006 Hummer H3

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

1 Answer

2007 Pontiac g6 wipers stay in upright position


Hey Derek , here is how the wipers park position is suppose to work !
Windshield wiper motor park operation is controlled by the body control module (BCM) using an input from the park switch within the wiper motor assembly. The BCM monitors the windshield wiper motor park switch circuit to determine if the windshield wiper blades are at the bottom of the glass. The circuit will be pulled to ground by the wiper motor park switch while the windshield wiper motor is operating. When the wiper switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the BCM will continue to operate the motor until the wipers reach the park position. If the ignition is turned OFF while the wipers are in mid-cycle, the wipers will stop immediately where they are. The BCM will park the wipers the next time the ignition is turned ON.
The wipers will not park when they are commanded ON and OFF with a scan tool. The BCM will park the wipers the next time the wiper switch is turned ON and OFF.
The BCM provides stall protection for the wiper motor by monitoring the park switch. If the park switch does not transition for 3 seconds while the wipers are operating, the BCM will assume that the wiper motor is stalled, and will de-energize the wiper relay until the wiper switch is cycled OFF and ON again.
Check for a voltage signal on the yellow wire at the wiper motor assembly , this is signal to the BCM ! If there is no signal you need to replace the windshield wiper motor assembly ? If there is a signal need to have Tech 2 scan tool hooked up to see if The BCM is the problem ! Relay #39 an #40 are the high an low wiper relays in the under hood fuse block ! Do you have a volt meter ,do you know how to do electrical testing ?

Sep 21, 2015 | Pontiac Cars & Trucks

1 Answer

Wipers stop in the middle of my wishield,will not park properly


Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jan 31, 2018 | 2005 Buick Century

1 Answer

Turn signal handle broke off and is hanging by wires


You can buy the turn signal switch at Napa or other auto parts stores. It's a combination switch. Remove the steering wheel and remove the 2 screws that hold the turn signal switch on, unplug the wires and installation is reverse of removal.

Apr 02, 2010 | 1992 Ford F150 SuperCab

1 Answer

Need to get a programmer dont know where its at


  • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
  • Damaged turn signal and windshield wiper switch .
  • Damaged windshield wiper motor .
  • Damaged windshield wiper control module.
7fd52e7.gif
efd7dbe.gif
Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :
  • Windshield wiper motor (17508) (F-type).
  • Washer system.
  • Windshield wiper control module.
  • Turn signal and windshield wiper switch (13K359).
The windshield wiper control module is:
  • Located at the instrument panel fuse panel.
The windshield wiper motor is:
  • Attached to the cowl top extension (021A36) .
  • Connected to windshield wiper mounting arm and pivot shaft (17566) .
The turn signal and windshield wiper switch features a:
  • Rotary wiper switch.
  • Push type washer actuator.
OFF/Low/High Speed
  • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
  • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
  • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
  • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
  • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
  • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
  • When the park switch contacts open, the windshield wiper motor stops in the park position.
Interval
When the turn signal and windshield wiper switch is in the interval position:
  • The wipers make single wipes separated by pauses.
  • The rotary switch is on the end of turn signal and windshield wiper switch .
  • The length of the pause can be set from approximately 1 to 17 seconds.
  • Length of pause decreases as the rotary switch is rotated away from off.
  • Length of pause increases as the rotary switch is rotated toward off.
While in the interval wiper mode:
  • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

May 27, 2009 | 1994 Ford Mustang

1 Answer

Ignition switch


  1. Remove the turn signal and windshield wiper switch.
  2. Disconnect the ignition switch electrical connector.
  3. Remove the two ignition key reminder switch screws.
  4. Remove the ignition switch screws and remove the ignition switch.
Installation

To install, reverse the removal procedure. Check for proper operation of the ignition switch.

Nov 04, 2008 | 1992 Mercury Tracer

Not finding what you are looking for?
1994 Buick Park Avenue Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...